2007 TOYOTA FJ CRUISER transmission

1202007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:gear km/h (mph) “H” or “HL” “LL”
1 48 (30) 18 (11)
2 93 (58) 35 (22)
3 138 (86) 53 (33)
4 172 (107) 66 (41)
5 175 (109) 80 (50)
NOTICE
Do not downshift if you are going
faster than the maximum allowable
speed for the next lower gear.
Good driving practice
If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use sixth gear.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.
NOTICE
 Make sure the vehicle is completely
stopped before shifting into reverse.
 Do not use any gears other than
first gear when starting off and
moving forward. Doing so may dam-
age the clutch.
TS17005
Use the fourwheel drive control lever
to select the following transfer modes.
“H” (high speed position): Lever at “H”
Use this for normal driving on dry hard −
surfaced roads. This position gives greater
economy, quietest ride and least wear.
“HL” (high speed position, center differ-
ential locked): Lever at “HL”
Use this for normal driving on wet, icy or
snow −covered roads.
“N” (neutral position): Lever at “N”
No power is delivered to the wheels. The
vehicle must be stopped.
Fourwheel drive system
(fulltime fourwheel drive
models)—
(a) Fourwheel drive control

1232007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
SHIFTING BETWEEN “H2” AND “H4”
To shift from “H2” to “H4”, reduce your
speed to less than 80 km/h (50 mph) and
move the front drive control lever.
If you have trouble shifting in cold weath-
er, reduce your speed or stop the vehicle
and reshift.
CAUTION
Never move the front drive control
lever if wheels are slipping. Stop the
slipping or spinning before shifting.
To shift from “H4” to “H2”, simply move
the front drive control lever.
This can be done at any vehicle speed.
If the indicator light does not go off when
you shift the transfer into “H2”, drive
straight ahead while accelerating or decel-
erating, or drive in reverse.
SHIFTING BETWEEN “H4” AND “L4”
Stop the vehicle, put the transmission into
“N” and move the front drive control lever. The traction control system automatical-
ly helps prevent the spinning of rear
wheels (twowheel drive models) or 4
wheels (fourwheel drive models) when
the vehicle is started or accelerated on
slippery road surfaces.
When the ignition key is turned to “ON”,
the system automatically turns on.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicle and
power to the rear wheels (twowheel
drive models) or 4 wheels (fourwheel
drive models) cannot be maintained,
even though the traction control sys-
tem is in operation. Do not drive the
vehicle under any speed or maneuver-
ing conditions which may cause the
vehicle to lose traction control. In si-
tuations where the road surface is
covered with ice or snow, your ve-
hicle should be fitted with snow tires
or tire chains. Always drive at an ap-
propriate and cautious speed for the
present road conditions.
TS17007
NORMAL DRIVING MODE
Leave the system on during the ordi-
nary driving so that it can operate
when needed.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the trac-
tion control system is in the self
−check
mode, but does not indicate a malfunction.
When the traction control system is oper-
ating, the following conditions occur:
(c) Shifting procedure Traction control system

1332007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
Part−time four −wheel drive models—
Before using the rear differential lock sys-
tem, first shift the four −wheel drive control
lever into “L4” to see if this is sufficient.
If this has no effect, additionally use the
rear differential lock system.
CAUTION
Do not use the rear differential lock
in the conditions other than above.
Large steering effort and careful cor-
nering control will be required.
TS17016
To lock the rear differential, push the
switch.
Be sure to stop the wheels before locking
the differential.
For easy locking on vehicle with manual
transmission, depress the clutch pedal,
push the lock switch and slowly release
the clutch pedal. On vehicle with automat-
ic transmission, push the lock switch and
gently depress the accelerator pedal.
The indicator light will blink when the
switch is turned on. Wait a few seconds
for the system to complete operation. Af-
ter the differential is locked, the light will
stop blinking and remain on. The following systems do not operate
when the rear differential is locked. It is
normal operation for the “ABS” warning
light, “VSC OFF” indicator light and slip
indicator light to be on at this time.
Anti
−lock brake system
Brake assist system
Vehicle stability control system
Traction control system
CAUTION
Do not lock the differential until the
wheels have stopped spinning.
Otherwise, the vehicle may move in
an unexpected direction when the
differential lock is engaged, result-
ing in an accident. This may also
lead to possible damage to differen-
tial lock component parts.
Do not drive over 8 km/h (5 mph)
when the differential is locked.

1352007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
The cruise control is designed to main-
tain a set cruising speed without requir-
ing the driver to operate the accelera-
tor. Cruising speed can be set to any
speed above 40 km/h (25 mph).
Within the limits of the engine’s capabili-
ties, cruising speed can be maintained up
or down grades. However, changes in ve-
hicle speed may occur on steeper grades.
CAUTION
To help maintain maximum control
of your vehicle, do not use the
cruise control when driving in
heavy or varying traffic, or on slip-
pery (rainy, icy or snowcovered) or
winding roads.
Avoid vehicle speed increases when
driving downhill. If the vehicle
speed is too fast in relation to the
cruise control set speed, cancel the
cruise control then downshift the
transmission to use engine braking
to slow down.
TS17013
TURNING THE SYSTEM ON AND OFF
To turn the cruise control on, press the
“ON−OFF” button. The “CRUISE” indicator
light on the instrument panel will come on
to indicate that the cruise control is opera-
tional. Pressing the “ON −OFF” button
again turns the system off.
When the system is turned off, cruising
speed must be reset when the cruise con-
trol is turned on again.
CAUTION
Due to the cruise control switch be-
ing located just behind the steering
wheel, there is a possibility that it
may be touched accidentally. To avoid
accidentally engaging the cruise con-
trol, turn the system off when it is
not in use. Make sure the “CRUISE”
indicator light is off.
Cruise control

1362007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS17014
SETTING THE CRUISING SPEED
On vehicles with automatic transmission,
the transmission must be in “D” or “4”
before you set the cruising speed.
Bring your vehicle to the desired speed,
push the lever down in the “− SET” direc-
tion and release it. This sets the vehicle
at that speed. If the speed is not satisfac-
tory, tap the lever up for a faster speed,
or tap it down for a slower speed. Each
tap changes the set speed by 1.6 km/h
(1.0 mph). You can now take your foot off
the accelerator pedal. If you need acceleration—for example,
when passing—depress the accelerator
pedal enough for the vehicle to exceed
the set speed. When you release it, the
vehicle will return to the speed set prior
to the acceleration.
CAUTION
For manual transmission:
While driving with the cruise control
on, do not shift to neutral without
depressing the clutch pedal, as this
may cause engine racing or overrev-
ving.
CANCELLING THE CRUISE CONTROL
The cruise control may be temporarily
cancelled by the driver or by the system
itself under certain circumstances. Tempo-
rary cancellation allows the set cruising
speed to remain in memory.
The cruise control can be temporarily can-
celled by doing the following:
Pulling the lever in the “CANCEL” di-
rection and releasing it
Depressing the brake pedal
Depressing the clutch pedalUnder certain circumstances, the cruise
control is temporarily cancelled:
When vehicle speed falls below 40
km/h (25 mph)
When vehicle stability control is acti-
vated
When vehicle speed drops 16 km/h (10
mph) below the set speed, the cruise con-
trol is cancelled and the set speed is
erased from memory.
The “CRUISE” indicator light remains on
to indicate that the system is still in op-
eration.
To turn the cruise control off, press the
“ON −OFF” button. Make sure the
“CRUISE” indicator light is off.
If the cruise control automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.
RESUMING THE CRUISE CONTROL
If the cruise control is temporarily can-
celled, the cruising speed can be resumed
by pushing the lever up in the “+ RES”
direction.
Vehicle speed must be above 40 km/h (25
mph).

1372007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
RESETTING TO A FASTER SPEED
Push the lever up in the “+ RES” direction
and hold it. Release the lever when the
desired speed is attained. While the lever
is held up, the vehicle will gradually gain
speed.
However, a faster way to reset is to ac-
celerate the vehicle and then push the
lever down in the “− SET” direction.
RESETTING TO A SLOWER SPEED
Push the lever down in the “− SET” direc-
tion and hold it. Release the lever when
the desired speed is attained. While the
lever is held down, the vehicle speed will
gradually decrease.
However, a faster way to reset is to de-
press the brake pedal and then push the
lever down in the “− SET” direction.
On vehicles with automatic transmission,
even if you downshift from “D” to “4”, with
the cruise control on, engine braking will
not be enabled because the cruise control
is not cancelled. To decrease the vehicle
speed, reset to a slower speed with the
cruise control lever or depress the brake
pedal. If you use the brake pedal, cruise
control is cancelled. CRUISE CONTROL FAILURE WARNING
If the “CRUISE” indicator light flashes
when using the cruise control, press the
“ON
−OFF” button to turn the system off
and then press it again to turn it on.
If any of the following conditions then oc-
curs, there is some trouble in the cruise
control system.
The indicator light does not come on.
The indicator light flashes again.
The indicator light goes out after it
comes on.
If this is the case, contact your Toyota
dealer and have your vehicle inspected.
TS17019
To crank the engine without depressing
the clutch pedal, push the switch with
the ignition on.
The switch stays on as long as the igni-
tion is on. And it will automatically turn off
when the ignition is off. An indicator light
will illuminate to indicate the system is
operating.
This switch cancels the clutch start sys-
tem, which is designed to keep the starter
motor from operating if the clutch pedal is
not depressed all the way down.
The switch allows the vehicle to be driven
out of difficult situations by cranking the
engine with the clutch engaged.
Clutch start cancel switch

1922007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
NOTICE
To prevent the fuse from being
blown, do not use the electricity
over the total capacity of 12
VDC/120W.
 To prevent the battery from being
discharged, do not use the power
outlets longer than necessary when
the engine is not running.
 Close the power outlet lids when
the power outlets are not in use.
Inserting anything other than an ap-
propriate plug that fits the outlet,
or allowing any liquid to get into
the outlet may cause electrical fail-
ure or short circuits.
TS10002
This power outlet is designed for use
as a power supply for electric ap-
pliances.
The power outlet must only be used after
the engine is started.
If the engine is started with the power
outlet main switch on, the maximum ca-
pacity of the power supply may decrease
to below the standard, or may be cut off
completely, even when the vehicle is sta-
tionary.
While the vehicle is being driven, the
maximum capacity of the power outlet is
always 115 VAC/100W. When the vehicle
is stationary, the maximum capacity of the
power outlet varies depending on the fol-
lowing conditions (a) or (b): (a) The maximum capacity is 115
VAC/400W when the following condi-
tion applies:
Automatic transmission models: The
selector lever is in the “P” or “N” posi-
tion.
Manual transmission models: The shift
lever is in the neutral position and the
clutch pedal is not depressed.
(b) The maximum capacity is 115 VAC/100W when the following condi-
tion applies:
Automatic transmission models: The
selector lever is moved to any posi-
tions other than “P” and “N”.
Manual transmission models: The
clutch pedal is depressed.
A maximum capacity of 400W can only be
restored by turning the power outlet main
switch off and then on again under condi-
tion (a) described above.
Power outlet (115 VAC)

1932007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
The protection circuit may be activated to
cut the power supply if any of the follow-
ing conditions apply:
The engine is started with the power
outlet switch on.
Use of electrical appliances exceeding
the maximum capacity is attempted.
A sound may be heard when the
protection circuit is activated. This is
normal and does not indicate a mal-
function.
Electrical appliances, which consume
power exceeding 100W, have been
used continuously for a long time per-
iod.
The total power usage by all electrical
features (headlights, air conditioning,
etc.) has exceeded the total vehicle
maximum for an extended period of
time.
If the protection circuit is activated and
the power supply is cut, conduct the fol-
lowing procedure:
1. Park the vehicle in a safe area, and then securely apply the parking brake.
2. Check and ensure the following condi- tions: Automatic transmission models: The
selector lever is in the “P” or “N” posi-
tion.
Manual transmission models: The shift
lever is in the neutral position and the
clutch pedal is not depressed.
3. Make sure that the power consumption of the electric appliance is within the
maximum capacity of the power outlet
and the appliance is not broken.
4. Push the power outlet main switch again.
When the cabin temperature is high, open
the windows to cool the temperature
down. Once it reaches the normal temper-
ature, turn the power outlet main switch
on again.
If the power supply is not resumed even
after performing the above procedure,
have the vehicle inspected by a Toyota
dealer.
TS10003
Indicator light
(green)
Indicator light
(yellow)
To use the power outlet, push the main
switch located on the instrument panel.
The color of the indicator light changes
according the maximum available capacity,
as follows: Illumination color
Maximum capacity
Green and yellow115 VAC/400W
Ye l l o w115 VAC/100W
To turn the power outlet off, push the
main switch again. When the power outlet
is not in use, make sure that the main
switch is off and that the indicator light is
not illuminated.