2007 TOYOTA FJ CRUISER turn signal bulb

912007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS15002
HighLow beams—For high beams, turn
the headlights on and push the lever away
from you (position 1). Pull the lever to-
ward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will
tell you that the high beams are on.
Flashing the high beam headlights
(position 3)—Pull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights
with the knob turned to “OFF”.
TS15003
TURN SIGNALS
To signal a turn, push the headlight/
turn signal lever up or down to position
1.
The key must be in the “ON” position.
The lever automatically returns after you
make a turn, but you may have to return
it by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position
2) and hold it.
If the turn signal indicator lights (green
lights) on the instrument panel flash faster
than normal, a front or rear turn signal
bulb is burned out. See “Replacing light
bulbs” on page 309 in Section 7 −3.
TS15004
To turn on the emergency flashers,
push the switch.
All the turn signal lights will flash. To turn
them off, push the switch once again.
Turn on the emergency flashers to warn
other drivers if your vehicle must be
stopped where it might be a traffic hazard.
Always pull as far off the road as pos-
sible.
The turn signal light switch will not work
when the emergency flashers are operat-
ing.
Emergency flashers

3102007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
The inside of the lens of exterior lights
such as headlights may temporarily fog up
when the lens becomes wet in the rain or
in a car wash. This is not a problem
because the fogging is caused by the
temperature difference between the outside
and inside of the lens, just like the
windshield fogs up in the rain. However, if
there is a large drop of water on the
inside of the lens, or if there is water
pooled inside the light, contact your
Toyota dealer.Light bulbsBulb
No.WTy p e
Headlights—60/55A
Front turn signal/
parking and front
side marker lights
—21/5B
Outside rear view
mirror illumination
lights
—5C
Rear turn signal
lights567421D
Tail/stop and rear
side marker lights744321/5C
Back −up lights92118C
License plate
lights—5C
Interior light—8E
Luggage compart-
ment light—8E
A: HB2 halogen
B: Single end bulbs
C: Wedge base bulbs
D: Wedge base bulbs (amber)
E: Double end bulbs
TS73003
1. Open the hood. Unplug the connec-
tor. Remove the rubber cover.
If the connector is tight, wiggle it.
—Headlights

3112007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
TS73004
2. Release the bulb retaining springand remove the bulb. Install a new
bulb and the bulb retaining spring.
To install a bulb, align the tabs of the
bulb with the cutouts of the mounting
hole.
TS73005
3. Install the rubber cover as shown and fit it securely on the boss. Plug
in the connector.
Make sure the rubber cover fits securely
on the connector and the headlight body.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.
TS73006
TS73007
—Front turn signal/parking
and front side marker lights

3122007 FJ CRUISER from Oct. ’06Prod. (OM35873U)
If either the left or right outside rear
view mirror illumination light burns out,
contact your Toyota dealer.
NOTICE
Do not try to replace the outside rear
view mirror illumination light bulbs by
yourself. You may damage the ve-
hicle.TS73008
Use a flathead screwdriver which is
wrapped with a cloth.
TS73009
TS73010
a: Backup light
b: Tail/stop and rear side marker lights
c: Rear turn signal light
—Outside rear view mirror
illumination lights
(on some models)—Tail/stop and rear side
marker, rear turn signal and
backup lights