2007 TOYOTA CAMRY HYBRID warning light

’07Camry hybrid_U (L/O 0610)
359
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
To check the fluid level, simply look at
the seethrough reservoir. The level
should be between the “MAX” and
“MIN” lines on the reservoir.
It is normal for the brake fluid level to go
down slightly as the brake pads wear or
when the fluid level in the accumulator is
high.
If the level is low, take your vehicle to
a Toyota dealer as soon as possible. Do
not drive your vehicle if the red brake
system warning light is on. Call a
Toyota dealer for assistance.If the fluid level goes down soon after
your vehicle is serviced, it may indicate
a serious mechanical problem. Have
your vehicle checked by a Toyota deal-
er.
CAUTION
Brake fluid can harm your hands or
eyes. If fluid gets on your hands or
in your eyes, flush the affected area
with clean water immediately. If you
still feel uncomfortable with your
hands or eyes, go to the doctor.
NOTICE
If brake fluid is spilled on the vehicle,
be sure to wipe it off to prevent dam-
age to parts or paint.
Ty p e A
Checking brake fluid
Checking tire inflation
pressure

’07Camry hybrid_U (L/O 0610)
367
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.
If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.
WHEEL SELECTION
When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.
Correct replacement wheels are available
at your Toyota dealer.
A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis.Replacement with used wheels is not rec-
ommended as they may have been sub-
jected to rough treatment or high mileage
and could fail without warning. Also, bent
wheels which have been straightened may
have structural damage and therefore
should not be used. Never use an inner
tube in a leaking wheel which is designed
for a tubeless tire.
CAUTION
Do not use wheels other than the
manufacturer ’s recommended size, as
this may cause dangerous handling
characteristics resulting in loss of
control. Otherwise, an accident may
occur resulting in death or serious
injuries.
Initial adjustment of the tire pressure
warning system is necessary after you
have replaced your wheels. See “Tire
pressure warning system” on page 168
in Section 17.
When installing aluminum wheels,
check that the wheel nuts are tight
after driving your vehicle the first 1600
km (1000 miles).
If you have rotated, repaired, or
changed your tires, check that the
wheel nuts are still tight after driving
1600 km (1000 miles).
When using tire chains, be careful not
to damage the aluminum wheels.
Use only Toyota wheel nuts and
wrench designed for your aluminum
wheels.
When balancing your wheels, use only
Toyota balance weights or equivalent
and a plastic or rubber hammer.
As with any wheel, periodically check
your aluminum wheels for damage. If
damaged, replace immediately.
Replacing wheels
Aluminum wheel precautions

’07Camry hybrid_U (L/O 0610)
387
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
26. HLP(LL) 15 A: Left−hand headlight
(low beam)
27. HLP(RH) 15 A: Right−hand headlight
(high beam)
28. HLP(LH) 15 A: Left−hand headlight
(high beam)
29. HTR 50 A: Air conditioning system
30. HTR SUB2 50 A: PTC heater
31. HTR SUB1 50 A: PTC heater
32. RR DEF 50 A: Rear window defogger,
“MIR HTR” fuse
33. CDS FAN 40 A: Electric cooling fans
34. RDI FAN 40 A: Electric cooling fans
35. DC/DC 120 A: “ABS MTR2”, “EPS”,
“ABS MTR”, “AM2”, DOOR NO.1”,
“ETCS”, “IG2”, “HAZ”, “AMP”, “ABS
MAIN1”, “ABS MAIN2”, “STR LOCK”,
“ABS MAIN3”, “BTT FAN”, “EFI MAIN”,
“EFI NO.1” and “IGCT” fuses
36. EPS 80 A: Electric power steering sys-
tem
37. ABS MTR2 40 A: Electronically con-
trolled brake system
38. ABS MTR1 50 A: Electronically con-
trolled brake system
INSTRUMENT PANEL
1. RR DOOR RH 25 A: Rear right power
window
2. RR DOOR LH 25 A: Rear left power
window
3. FUEL OPN 7.5 A: Fuel fillter door
opening system
4. FR FOG 15 A: No circuit
5. OBD 7.5 A: On−board diagnosis sys-
tem
6. ECUB NO.2 7.5 A: No circuit7. STOP 10 A:
Stop lights, high mounted
stoplight, shift lock control system,
multiport fuel injection system/sequen-
tial multiport fuel injection system, main
body ECU, electronically controlled
brake system, electronic throttle control
system
8. TI&TE 30 A: No circuit
9. AM1 7.5 A: Starting system, multiport
fuel injection system/sequential multi-
port fuel injection system
10. A/C 7.5 A: Air conditioning system
11. PWR 25 A: Power windows
12. DOOR NO.2 25 A: Main body ECU
13. S/ROOF 30 A: Electric moon roof
14. TAIL 15 A: Front side marker lights,
tail lights, rear side marker lights, li-
cense plate lights
15. PANEL 7.5 A: Navigation system, seat
heaters, emergency flashers, air condi-
tioning system, audio system, glove
box light, instrument panel lights, steer-
ing switches, clock
16. ECU IG NO.1 10 A: Main body ECU,
push start system, electric moon roof,
auto anti −glare inside rear view mirror,
tire pressure warning system, naviga-
tion system