2007 SUZUKI XL7 warning

5-37 SERVICE AND APPEARANCE CARE
78J00-03E
Wheel ReplacementReplace any wheel that is bent, cracked,
or badly rusted or corroded. If wheel nuts
keep coming loose, the wheel, wheel bolts,
and wheel nuts should be replaced. If the
wheel leaks air, replace it (except some
aluminum wheels, which can sometimes
be repaired). See your dealer if any of
these conditions exist.
Your dealer will know the kind of wheel you
need.
Each new wheel should have the same
load-carrying capacity, diameter, width,
offset, and be mounted the same way as
the one it replaces.
If you need to replace any of your wheels,
wheel bolts or wheel nuts, replace them
only with new original equipment parts.
This way, you will be sure to have the right
wheel, wheel bolts, and wheel nuts for
your vehicle.Refer to “Changing a Flat Tire” in this sec-
tion for more information.
Used Replacement Wheels
Tire Chains
If a Tire Goes FlatIt is unusual for a tire to blowout while you
are driving, especially if you maintain your
vehicle’s tires properly. If air goes out of a
tire, it is much more likely to leak out
slowly. But if you should ever have a blow-
out, here are a few tips about what to
expect and what to do:
WARNING
Using the wrong replacement wheels,
wheel bolts, or wheel nuts on your
vehicle can be dangerous. It could
affect the braking and handling of
your vehicle, make your tires lose air
and make you lose control. You
could have a collision in which you
or others could be injured. Always
use the correct wheel, wheel bolts,
and wheel nuts for replacement.
CAUTION
The wrong wheel can also cause
problems with bearing life, brake
cooling, speedometer or odometer
calibration, headlamp aim, bumper
height, vehicle ground clearance, and
tire or tire chain clearance to the
body and chassis.
WARNING
Putting a used wheel on your vehicle
is dangerous. You cannot know how
it has been used or how far it has
been driven. It could fail suddenly
and cause a crash. If you have to
replace a wheel, use a new original
equipment wheel.
WARNING
Do not use tire chains. There is not
enough clearance. Tire chains used
on a vehicle without the proper
amount of clearance can cause dam-
age to the brakes, suspension or
other vehicle parts. The area dam-
aged by the tire chains could cause
you to lose control of your vehicle
and you or others may be injured in a
crash.
Use another type of traction device
only if its manufacturer recommends
it for use on your vehicle and tire size
combination and road conditions.
Follow that manufacturer’s instruc-
tions. To help avoid damage to your
vehicle, drive slowly, readjust or
remove the device if it is contacting
your vehicle, and do not spin your
vehicle’s wheels. If you do find trac-
tion devices that will fit, install them
on the front tires.

5-38 SERVICE AND APPEARANCE CARE
78J00-03E
If a front tire fails, the flat tire will create a
drag that pulls the vehicle toward that side.
Take your foot off the accelerator pedal
and grip the steering wheel firmly. Steer to
maintain lane position, and then gently
brake to a stop well out of the traffic lane.
A rear blowout, particularly on a curve,
acts much like a skid and may require the
same correction you would use in a skid. In
any rear blowout remove your foot from
the accelerator pedal. Get the vehicle
under control by steering the way you want
the vehicle to go. It may be very bumpy
and noisy, but you can still steer. Gently
brake to a stop, well off the road if possi-
ble.
If a tire goes flat, the next part shows how
to use the jacking equipment to change a
flat tire safely.
Changing a Flat TireIf a tire goes flat, avoid further tire and
wheel damage by driving slowly to a level
place. Turn on your vehicle’s hazard warn-
ing flashers. Refer to “Hazard Warning
Flashers” in “Instrument Panel Overview”
in the “Instrument Panel” section for more
information.
When your vehicle has a flat tire, use the
following example as a guide to assist you
in the placement of wheel blocks.
809231
The following information will tell you next
how to use the jack and change a tire.
Removing the Spare Tire and Tools
To access the tools, do the following:
1) Locate the jack and wheel wrench,
which are located on the passenger’s
side of the rear cargo area, behind an
access door. Pull out the access door
to reach them.
WARNING
Lifting a vehicle and getting under it
to do maintenance or repairs is dan-
gerous without the appropriate safety
equipment and training. The jack pro-
vided with your vehicle is designed
only for changing a flat tire. If it is
used for anything else, you or others
could be badly injured or killed if the
vehicle slips off the jack. Use the jack
provided with your vehicle only for
changing a flat tire.
WARNING
Changing a tire can be dangerous.
The vehicle can slip off the jack and
roll over or fall on you or other peo-
ple. You and they could be badly
injured or even killed. Find a level
place to change your tire. To help
prevent the vehicle from moving:
1) Set the parking brake firmly.
2) Put the shift lever in PARK (P).
3) Turn off the engine and do not
restart while the vehicle is raised.
4) Do not allow passengers to
remain in the vehicle.
To be even more certain the vehicle
will not move, you should put blocks
at the front and rear of the tire far-
thest away from the one being
changed. That would be the tire, on
the other side, at the opposite end of
the vehicle.

5-41 SERVICE AND APPEARANCE CARE
78J00-03E
5) Put the compact spare tire near the flat
tire.
988777
6) Raise the vehicle by turning the jack
handle clockwise. Raise the vehicle far
enough off the ground so there is
enough room for the road tire to clear
the ground.
806071
7) Remove all of the wheel nuts.
8) Remove the flat tire.
WARNING
Getting under a vehicle when it is
jacked up is dangerous. If the vehicle
slips off the jack you could be badly
injured or killed. Never get under a
vehicle when it is supported only by
a jack.
WARNING
Raising your vehicle with the jack
improperly positioned can damage
the vehicle and even make the vehi-
cle fall. To help avoid personal injury
and vehicle damage, be sure to fit the
jack lift head into the proper location
before raising the vehicle.
WARNING
Lifting a vehicle and getting under it
to do maintenance or repairs is dan-
gerous without the appropriate safety
equipment and training. The jack pro-
vided with your vehicle is designed
only for changing a flat tire. If it is
used for anything else, you or others
could be badly injured or killed if the
vehicle slips off the jack. Use the jack
provided with your vehicle only for
changing a flat tire.
WARNING
Rust or dirt on the wheel, or on the
parts to which it is fastened, can
make the wheel nuts become loose
after time. The wheel could come off
and cause an accident. When you
change a wheel, remove any rust or
dirt from the places where the wheel
attaches to the vehicle. In an emer-
gency, you can use a cloth or a paper
towel to do this; but be sure to use a
scraper or wire brush later, if needed,
to get all the rust or dirt off.

5-42 SERVICE AND APPEARANCE CARE
78J00-03E
811105
9) Remove any rust or dirt from the wheel
bolts, mounting surfaces, and spare
wheel.
10)Place the compact spare tire on the
wheel-mounting surface.
11)Reinstall the wheel nuts. Tighten each
nut by hand until the wheel is held
against the hub.
1152288
12)Lower the vehicle by turning the jack
handle counterclockwise.
808642
13)Tighten the wheel nuts firmly in a criss-
cross sequence, as shown.
14)Lower the jack all the way and remove
the jack from under the vehicle.
15)Tighten the wheel nuts firmly with the
wheel wrench.
WARNING
Never use oil or grease on studs or
nuts. If you do, the nuts might come
loose. Your wheel could fall off, caus-
ing a serious accident.
WARNING
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the
wheel to come loose and even come
off. This could lead to an accident. Be
sure to use the correct wheel nuts. If
you have to replace them, be sure to
get new SUZUKI original equipment
wheel nuts. Stop somewhere as soon
as you can and have the nuts tight-
ened with a torque wrench to the
proper torque specification. Refer to
“Capacities and Specifications” in
this section for wheel nut torque
specification.
CAUTION
Improperly tightened wheel nuts can
lead to brake pulsation and rotor
damage. To avoid expensive brake
repairs, evenly tighten the wheel nuts
in the proper sequence and to the
proper torque specification. Refer to
“Capacities and Specifications” in
this section for the wheel nut torque
specification.

5-43 SERVICE AND APPEARANCE CARE
78J00-03E
Secondary Latch System
Your vehicle has an underbody mounted
tire hoist assembly equipped with a sec-
ondary latch system. It is designed to stop
the compact spare tire from suddenly fall-
ing off your vehicle if the cable holding the
spare tire is damaged. For the secondary
latch to work, the tire must be stowed with
the valve stem pointing down. Refer to
“Storing a Flat or Spare Tire and Tools” in
this section for instructions on storing the
spare tire correctly.To release the spare tire from the second-
ary latch, do the following:
1) If the cable is not visible, start this pro-
cedure at Step 3.
806961
2) If the cable is visible, place the wrench
on the hoist drive nut and turn the
wrench counterclockwise until approxi-
mately 6 inches (15 cm) of cable is
exposed.
3) Attach the wheel wrench to the jack and
raise the jack at least 10 turns.
4) Place the jack under the vehicle, ahead
of the rear bumper. Position the center
lift point of the jack under the center of
the spare tire.
806546
5) Turn the wheel wrench clockwise to
raise the jack until it lifts the secondary
latch spring.
6) Keep raising the jack until the spare tire
stops moving upward and is held firmly
in place, this lets you know that the sec-
ondary latch has released.
7) Lower the jack by turning the wheel
wrench counterclockwise. Keep lower-
ing the jack until the spare tire is resting
on the wheel wrench.
WARNING
Before beginning this procedure read
all the instructions. Failure to read
and follow the instructions could
damage the hoist assembly and you
and others could get hurt. Read and
follow the instructions listed next.
WARNING
Someone standing too close during
the procedure could be injured by the
jack. If the spare tire does not slide
off the jack completely, make sure no
one is behind you or on either side of
you as you pull the jack out from the
under spare.

5-44 SERVICE AND APPEARANCE CARE
78J00-03E
806548
8) Grasp the spare tire with both hands
and pull it out from under the vehicle.
9) Reach under the vehicle and remove
the wheel wrench and jack.
1613524
10)Tilt the retainer and slip it through the
wheel opening when the spare tire has
been completely lowered.
11)Turn the wrench clockwise to raise the
cable back up if the cable is hanging.
Have the hoist assembly inspected as
soon as you can. You will not be able to
store a spare tire using the hoist assembly
until it has been repaired or replaced.Storing a Compact Spare Tire
WARNING
Storing a jack, a tire, or other equip-
ment in the passenger compartment
of the vehicle could cause injury. In a
sudden stop or collision, loose
equipment could strike someone.
Store all these in the proper place.
WARNING
The underbody-mounted spare tire
needs to be stored with the valve
stem pointing down. If the spare tire
is stored with the valve stem pointing
upward, its secondary latch will not
work properly and the spare tire
could loosen and suddenly fall from
your vehicle. If this happened when
your vehicle was being driven, the
tire might contact a person or
another vehicle, causing injury and,
of course, damage to itself as well.
Be sure the underbody-mounted
spare tire is stored with its valve
stem pointing down.

5-49 SERVICE AND APPEARANCE CARE
78J00-03E
 For solid dry soils: remove as much as
possible and then vacuum.
To clean, use the following instructions:
1) Saturate a lint-free, clean white cloth
with water or club soda.
2) Wring the cloth to remove excess mois-
ture.
3) Start on the outside edge of the soil and
gently rub toward the center. Continue
cleaning, using a clean area of the cloth
each time it becomes soiled.
4) Continue to gently rub the soiled area
until the cleaning cloth remains clean.
5) If the soil is not completely removed,
use a mild soap solution and repeat the
cleaning process that was used with
plain water.
If any of the soil remains, a commercial
fabric cleaner or spot lifter may be neces-
sary. When a commercial upholstery
cleaner or spot lifter is to be used, test a
small hidden area for colorfastness first. If
the locally cleaned area gives any impres-
sion that a ring formation may result, clean
the entire surface.
After the cleaning process has been com-
pleted, a paper towel can be used to blot
excess moisture from the fabric or carpet.LeatherA soft cloth dampened with water may be
used to remove dust. If a more thorough
cleaning is necessary, a soft cloth damp-ened with a mild soap solution can be
used. Allow the leather to dry naturally. Do
not use heat to dry. Never use steam to
clean leather. Never use spot lifters or spot
removers on leather. Many commercial
leather cleaners and coatings that are sold
to preserve and protect leather may per-
manently change the appearance and feel
of your leather and are not recommended.
Do not use silicone or wax-based prod-
ucts, or those containing organic solvents
to clean your vehicle’s interior because
they can alter the appearance by increas-
ing the gloss in a non-uniform manner.
Never use shoe polish on your leather.
Instrument Panel, Vinyl, and Other
Plastic SurfacesA soft cloth dampened with water may be
used to remove dust. If a more thorough
cleaning is necessary, a clean soft cloth
dampened with a mild soap solution can
be used to gently remove dust and dirt.
Never use spot lifters or removers on plas-
tic surfaces. Many commercial cleaners
and coatings that are sold to preserve and
protect soft plastic surfaces may perma-
nently change the appearance and feel of
your interior and are not recommended.
Do not use silicone or wax-based prod-
ucts, or those containing organic solvents
to clean your vehicle’s interior because
they can alter the appearance by increas-
ing the gloss in a non-uniform manner.Some commercial products may increase
gloss on your instrument panel. The
increase in gloss may cause annoying
reflections in the windshield and even
make it difficult to see through the wind-
shield under certain conditions.
Care of Safety BeltsKeep belts clean and dry.WeatherstripsSilicone grease on weatherstrips will make
them last longer, seal better, and not stick
or squeak. Apply silicone grease with a
clean cloth. During very cold, damp
weather frequent application may be
required. Refer to “Recommended Fluids
and Lubricants” in “Maintenance Sched-
ule” in the “Maintenance Schedule” sec-
tion.Washing Your VehicleThe paint finish on the vehicle provides
beauty, depth of color, gloss retention, and
durability.
WARNING
Do not bleach or dye safety belts. If
you do, it may severely weaken them.
In a crash, they might not be able to
provide adequate protection. Clean
safety belts only with mild soap and
lukewarm water.

6-1 MAINTENANCE SCHEDULE
78J00-03E
Maintenance ScheduleIntroductionImportant: Keep engine oil at the proper
level and change as recommended.Maintenance RequirementsYour Vehicle and the Environment
Proper vehicle maintenance not only helps
to keep your vehicle in good working condi-
tion, but also helps the environment. All
recommended maintenance is important.
Improper vehicle maintenance can even
affect the quality of the air we breathe.
Improper fluid levels or the wrong tire infla-
tion can increase the level of emissions
from your vehicle. To help protect our envi-
ronment, and to keep your vehicle in good
condition, be sure to maintain your vehicle
properly.Using the Maintenance ScheduleWe want to help you keep your vehicle in
good working condition. But we do not
know exactly how you will drive it. You may
drive very short distances only a few times
a week. Or you may drive long distances
all the time in very hot, dusty weather. You
may use your vehicle in making deliveries.
Or you may drive it to work, to do errands,
or in many other ways.
Because of all the different ways people
use their vehicles, maintenance needs
vary. You may need more frequent checks
and replacements. So please read the fol-
lowing and note how you drive. If you have
any questions on how to keep your vehicle
in good condition, see your dealer.This schedule is for vehicles that:
 carry passengers and cargo within rec-
ommended limits. You will find these lim-
its on the Tire and Loading Information
label. Refer to “Loading Your Vehicle” in
“Your Driving, the Road, and Your Vehi-
cle” in the “Driving Your Vehicle” section.
 are driven on reasonable road surfaces
within legal driving limits.
 use the recommended fuel. Refer to
“Gasoline Octane” in “Fuel” in the “Ser-
vice and Appearance Care” section.
The services in “Scheduled Maintenance”
in this section should be performed when
indicated. Refer to “Additional Required
Services” in this section for further informa-
tion.
CAUTION
Maintenance intervals, checks,
inspections, replacement parts, and
recommended fluids and lubricants
as prescribed in this manual are nec-
essary to keep your vehicle in good
working condition. Any damage
caused by failure to follow scheduled
maintenance might not be covered by
warranty.
WARNING
Performing maintenance work on a
vehicle can be dangerous. In trying to
do some jobs, you can be seriously
injured. Do your own maintenance
work only if you have the required
know-how and the proper tools and
equipment for the job. If you have any
doubt, see your dealer to have a qual-
ified technician do the work. Refer to
“Doing Your Own Service Work” in
the “SERVICE AND APPEARANCE
CARE” section.