2007 SATURN VUE lock

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 324.
B. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 318.
C. Engine Oil Fill Cap (Out of View). See “When
to Add Engine Oil” underEngine Oil on
page 318.
D. Remote Negative (−) Terminal. SeeJump
Starting on page 348.
E. Brake Fluid Reservoir. SeeBrakes on
page 343.F. Battery. SeeBattery on page 347.
G. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 411.
H. Remote Positive (+) Terminal (Out of View).
SeeJump Starting on page 348.
I. Engine Coolant Surge Tank. See “Checking
Coolant” underEngine Coolant on page 331.
J. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 341.
317
ProCarManuals.com

1. You can remove the coolant surge tank
pressure cap when the cooling system,
including the coolant surge tank pressure cap
and upper radiator hose, is no longer hot.
Turn the pressure cap slowly counterclockwise
about one-quarter of a turn.
If you hear a hiss, wait for that to stop.
This will allow any pressure still left to be
vented out the discharge hose.
2. Then keep turning the pressure cap slowly,
and remove it.3. Fill the coolant surge tank with the proper
DEX-COOL®coolant mixture, to the COLD
FILL line.
340
ProCarManuals.com

Notice:If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles.
Unplug unnecessary accessories plugged into
the cigarette lighter or the accessory power
outlet. Turn off the radio and all lamps that are
not needed. This will avoid sparks and help
save both batteries. And it could save
the radio!
4. Open the hood on the other vehicle and
locate the positive (+) and negative (−)
terminal locations on that vehicle.
Open the hood on your vehicle and nd the
remote positive (+) and remote negative (−)
jump starting terminals.A. Remote Positive
B. Remote Negative
Vehicles equipped with the 2.2L L4 engine,
the remote positive (+) terminal is located
in the engine compartment on the driver’s side
of the vehicle, on the underhood fuse block.
SeeEngine Compartment Overview on
page 314for more information on location.
Access the remote positive (+) terminal
by removing the fuse block cover.
The remote negative (−) terminal is the lift
hook, which is located towards the rear of the
engine on the driver’s side.
2.2L L4 Engine
349
ProCarManuals.com

6. Connect the red positive (+) cable to the
positive (+) terminal on the vehicle with
the dead battery. Use a remote positive (+)
terminal if the vehicle has one.
7. Do not let the other end touch metal. Connect
it to the positive (+) terminal of the good
battery. Use a remote positive (+) terminal if
the vehicle has one.
8. Now connect the black negative (−) cable to
the negative (−) terminal of the good battery.
Use a remote negative (−) terminal if the
vehicle has one.
Do not let the other end touch anything
until the next step. The other end of the
negative (−) cable does not go to the dead
battery. It goes to a heavy, unpainted
metal engine part or to a remote negative (−)
terminal on the vehicle with the dead
battery.9. Connect the other end of the negative (−)
cable away from the dead battery, but not
near engine parts that move. The electrical
connection is just as good there, and the
chance of sparks getting back to the battery is
much less.
Your vehicle has a remote negative (−)
terminal for this purpose.
10. Now start the vehicle with the good battery
and run the engine for a while.
11. Press the unlock symbol on the remote
keyless entry transmitter to disarm your
security system, if equipped.
12. Try to start the vehicle that had the dead
battery. If it will not start after a few tries, it
probably needs service.
352
ProCarManuals.com

Notice:If the jumper cables are connected or
removed in the wrong order, electrical shorting
may occur and damage the vehicle. The repairs
would not be covered by your warranty. Always
connect and remove the jumper cables in the
correct order, making sure that the cables do
not touch each other or other metal.
A. Heavy, Unpainted Metal Engine Part or
Remote Negative (−) Terminal
B. Good Battery or Remote Positive (+) and
Remote Negative (−) Terminals
C. Dead Battery or Remote Positive (+) TerminalTo disconnect the jumper cables from both
vehicles, do the following:
1. Disconnect the black negative (−) cable from
the vehicle that had the dead battery.
2. Disconnect the black negative (−) cable from
the vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the
other vehicle.
5. Return the underhood fuse block cover to its
original position, if applicable.
All-Wheel Drive
If you have an all-wheel-drive vehicle, be sure to
perform the lubricant checks described in this
section. There are two additional systems
that need lubrication.
Jumper Cable Removal
353
ProCarManuals.com

7. Locate the vertical headlamp aiming screws,
which are under the hood near each headlamp
assembly.
The adjustment screw can be turned with a
6 mm socket.
8. Turn the vertical aiming screw until
the headlamp beam is aimed to the
horizontal tape line. Turn it clockwise or
counterclockwise to raise or lower the angle
of the beam.9. Make sure that the light from the headlamp is
positioned at the bottom edge of the horizontal
tape line. The lamp on the left (A) shows
the correct headlamp aim. The lamp on the
right (B) shows the incorrect headlamp aim.
10. Repeat Steps 7 through 9 for the opposite
headlamp.
357
ProCarManuals.com

4. Insert a at blade tool through the opening in
the top. Make sure the tool ts through the
opening in the headlamp bracket lower arm.5. Push the locking tab toward the rear of the
vehicle with the tool to lift the headlamp
bracket lower arm.
6. Pull back on the front fascia and then pull the
headlamp assembly out from the vehicle. You
may need someone to assist you with this step.
7. Disconnect the electrical connector from the
bulb assembly.
8. Turn the bulb assembly counterclockwise to
remove it from the housing.
9. Replace the old bulb with a new one.
10. Reverse Steps 1 through 8 to reinstall.
360
ProCarManuals.com

Front Turn Signal and
Parking Lamps
To replace a front turn signal or parking lamp
bulb, do the following:
1. Follow Steps 1 through 6 underHeadlamps
on page 358to access the front turn signal
or parking lamp.
2. Turn the bulb to be replaced counterclockwise
to remove it from the headlamp assembly.
3. Pull the bulb out of the bulb socket assembly.
4. Push the new bulb into the bulb socket
assembly.
5. Insert the bulb assembly into the headlamp
assembly.
6. Turn the bulb assembly clockwise until
seated.
7. Reverse the steps to reinstall the headlamp
assembly.
361
ProCarManuals.com