2007 SATURN RELAY garage door opener

4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release both
buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for
two seconds and then turns to a constant light,
continue with Steps 6 through 8 following to
complete the programming of a rolling-code
device, most commonly, a garage door opener.6. Locate in the garage, the garage door
opener receiver (motor-head unit). Locate the
“Learn” or “Smart” button. This can usually
be found where the hanging antenna wire is
attached to the motor-head unit.
7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release. Repeat
the press/hold/release sequence a second
time, and depending on the brand of the
garage door opener, or other rolling code
device, repeat this sequence a third time to
complete the programming.
The Universal Home Remote should now
activate the rolling-code device.
To program the remaining two Universal
Home Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.”
Do not repeat Step 1, as this will erase all
previous programming from the Universal
Home Remote buttons.
165
ProCarManuals.com

Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to time out or quit after several seconds
of transmission. This may not be long enough
for Universal Home Remote to pick up the signal
during programming. Similarly, some U.S. gate
operators are manufactured to time out in
the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator or garage door
opener by using the “Programming Universal
Home Remote” procedures, regardless of where
you live, replace Step 3 under “Programming
Universal Home Remote” with the following:
Continue to press and hold the Universal Home
Remote button while you press and release every
two seconds (cycle) the hand-held transmitter
button until the frequency signal has been
successfully accepted by the Universal Home
Remote. The Universal Home Remote indicator
light will ash slowly at rst and then rapidly.
Proceed with Step 4 under “Programming
Universal Home Remote” to complete.
Using Universal Home Remote
Press and hold the appropriate Universal Home
Remote button for at least half of a second.
The indicator light will come on while the signal is
being transmitted.
Erasing Universal Home Remote
Buttons
To erase programming from the three Universal
Home Remote buttons do the following:
1. Press and hold down the two outside buttons
until the indicator light begins to ash, after
20 seconds. Do not hold the two outside
buttons for longer than 30 seconds.
2. Release both buttons.
The Universal Home Remote is now in the
train (learning) mode and can be programmed
at any time beginning with Step 2 under
“Programming Universal Home Remote” shown
earlier in this section.
Individual buttons cannot be erased, but they
can be reprogrammed. See “Reprogramming a
Single Universal Home Remote Button” following
this section.
166
ProCarManuals.com

G
Gage
Engine Coolant Temperature.................... 228
Fuel......................................................... 233
Speedometer........................................... 221
Tachometer.............................................. 221
Garage Door Opener..........................156, 157
Gasoline
Octane..................................................... 414
Specications........................................... 414
Glove Box................................................... 167
GM Mobility Reimbursement Program.......... 543
H
Hazard Warning Flashers............................ 182
Head Restraints............................................ 13
Headlamp Wiring......................................... 511
Headlamps
Bulb Replacement.................................... 455
Daytime Running Lamps/Automatic
Headlamp System................................ 193Headlamps (cont.)
Flash-to-Pass........................................... 185
Halogen Bulbs......................................... 455
Headlamps and Sidemarker Lamps.......... 456
High/Low Beam Changer......................... 185
On Reminder........................................... 193
Wiper Activated........................................ 193
Headlamps and Sidemarker Lamps............. 456
Heated Seats................................................ 10
Heater................................................205, 209
Hideaway Rear Storage Bins....................... 174
Highbeam On Light..................................... 233
High-Speed Operation, Tires........................ 471
Highway Hypnosis....................................... 383
Hill and Mountain Roads............................. 384
Hood
Checking Things Under............................ 420
Release................................................... 421
Horn............................................................ 182
How to Use This Manual ................................ 4
How to Wear Safety Belts Properly............... 38
561
ProCarManuals.com