2007 SAAB 9-7X remote control

If you do not know if your garage door opener is a
xed code or rolling code device, open your
garage door opener’s remote control battery cover.
Your garage door opener is a xed code device
if there is a panel of switches. If not, your
garage door opener is a rolling code device.
Programming Universal Home
Remote — Fixed Code
Fixed Code garage door openers are used for
garage doors produced prior to 1996. Fixed code
uses the same coded signal every time, which
is manually programmed by setting DIP switches
for a unique personal code.
Follow these steps to program up to three channels:
1. Remove the battery cover of the hand-held
transmitter.
131
ProCarManuals.com

5. After entering the switch settings, press and
release all three buttons at the same time.
The indicator lights will turn on.
6. Press and hold the button you would like to use
to control the garage door until the garage door
moves. The indicator light above the selected
button should slowly blink. You may need to
hold the button from ve to 55 seconds.
7. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
8. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or
home lighting, repeat Steps 1 through 8, choosing
a different function button in Step 7 than what
you used for the garage door opener.Programming Universal Home
Remote — Rolling Code
Rolling code garage door openers are used for
garage doors produced after 1996 and are
code protected. Rolling code means the coded
signal is changed every time your remote control
garage door opener is used.
Programming a rolling code garage door opener
involves time-sensitive actions, so read the
entire procedure before you begin. If you do not
follow these actions, the device will time out
and you will have to repeat the procedure.
Follow these steps to program up to three channels:
1. Press the two outside buttons at the same
time for one to two seconds, and immediately
release them.
133
ProCarManuals.com

2. Go to the garage. Locate the garage door
motor head and press and release the
“learn” button.
After pressing the “learn” button, you have
10 to 30 seconds to complete Step 4
depending on your garage control unit. If you
cannot locate the “learn” button, refer to
the owner’s guide for your garage door opener.3. Press and hold the button you would like to
use to control the garage door until the
garage door moves. The indicator light, above
the selected button, should slowly blink.
You may need to hold the button from ve to
20 seconds.
4. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
5. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or
home lighting, repeat Steps 1 through 6, choosing
a different function button in Step 4 than what
you used for the garage door opener.
Using Universal Home Remote
Press and hold the appropriate button for at least
half of a second. The indicator light will come
on while the signal is being transmitted.
134
ProCarManuals.com

Overhead Console
Your vehicle may have this feature. The overhead
console may include reading lamps, a Universal
Home Remote, and a moonroof switch. See
the following for more information:
Reading Lamps on page 164.
Universal Home Remote System
(With Three Round LED) on page 128or
Universal Home Remote System
(With One Triangular LED) on page 129.
Moonroof on page 144.
Center Console Storage Area
Grasp the front lever on the center console while
lifting the top to open it.
The console may contain one or more of the
following components:
Rear Seat Audio Controls. SeeRear Seat
Audio (RSA) on page 257for more
information.
Rear Climate Control. SeeRear Climate
Control System on page 173for more
information.
Accessory Power Outlets. SeeAccessory
Power Outlet(s) on page 166for more
information.
Ignition Switch. SeeIgnition Positions on
page 107.
If your vehicle has the center armrest
compartment, lift the cover by pulling up on the
latch handle located underneath the front edge of
the armrest.
140
ProCarManuals.com

Instrument Panel Brightness
Turn the knob to adjust
the instrument panel
lights. Turn the
knob clockwise or
counterclockwise to
brighten or dim
the interior lamps.
Dome Lamps
The dome lamps will automatically come on when
you open a door, unless the dome lamp override
button is pressed in.
You can also turn on the dome lamps by turning the
instrument panel brightness control all the way
clockwise to the detent position. In this position, the
dome lamps will remain on until they are turned off.
Dome Lamp Override
The dome override
button is located to the
left of the steering
column on the
instrument panel.
To turn the dome lamps off, press the button.
The dome lamps will remain off when a door is
open. This will override the illuminated entry
feature unless you use your remote keyless entry
transmitter to unlock the vehicle.
To return the lamps to automatic operation, press
the button again. The dome lamps will come
on when you open any door.
163
ProCarManuals.com

Rear Climate Control System
The lower buttons on the rear seat audio are used
to adjust the rear seat climate controls. The
temperature of the air coming through the rear
outlets is determined by the front passenger’s
temperature setting.
z9y(Fan)Press this button to adjust the
fan speed.
z\y(Mode)Press this button to change the
direction of airow in the rear seat area to
either vent, bi-level or oor mode.
P(On/Off)Press this button to turn the rear
climate controls on or off.
The rear control will only turn on if the front is on
and not in defrost mode.
Climate Controls Personalization
Your vehicle is equipped with a Driver Information
Center (DIC). You can store and recall the
climate control settings for temperature, air delivery
mode and fan speed for two different drivers.
The personal choice settings recalled are
determined by the transmitter used to enter the
vehicle. After the button with the unlock symbol on
a remote keyless entry transmitter is pressed,
the climate control will adjust to the last settings of
the identied driver. The settings can also be
changed by pressing one of the memory
buttons (1 or 2) located on the driver’s door.
When adjustments are made, the new settings
are automatically saved for the driver.
173
ProCarManuals.com

Navigation/Radio System
Your vehicle may have a navigation radio system.
The navigation system has built-in features
intended to minimize driver distraction. Technology
alone, no matter how advanced, can never
replace your own judgment. See the Navigation
System manual for some tips to help you
reduce distractions while driving.
Rear Seat Entertainment System
Your vehicle may have a DVD Rear Seat
Entertainment (RSE) system. The RSE system
includes a DVD player, a video display screen,
two sets of wireless headphones, and a remote
control.
Parental Control
This button is located behind the video screen.
Press this button while a DVD or CD is playing to
freeze the video and mute the audio. The video
screen will display Parental Control ON and the
power indicator light on the DVD player will ash. It
will also disable all other button operations from the
remote control and the DVD player, with the
exception of the eject button. Press this button
again to restore operation of the DVD player.
This button may also be used to turn the DVD
player power on and automatically resume play if
the ignition is in RUN, ACC, or if RAP is active.
Before You Drive
The RSE system is for rear seat passengers only.
The driver cannot safely view the video screen
while driving and should not try to do so.
243
ProCarManuals.com

Stereo RCA Jacks
The RCA jacks are located behind the video
screen. The RCA jacks allow audio and video
signals to be connected from an auxiliary device
such as a camcorder or a video game unit to
the RSE system. Standard RCA cables, not
included, are needed to connect the auxiliary
device to the RCA jacks. The yellow connector
inputs video and the red and white connectors
input right and left audio. Refer to the
manufacturer’s instructions for proper connection
of the auxiliary device.
To use the auxiliary inputs on the RSE system,
connect an external auxiliary device to the
color-coded RCA jacks and turn both the auxiliary
device and the RSE system power on. If the
RSE system had been previously in the DVD
player mode, pressing the SRCE button on
the faceplate or the remote control will switch the
RSE system between the auxiliary device and
the DVD player.
How to Change the Video Format when in
the Auxiliary Mode
The auxiliary input video format is preset to NTSC.
In some countries, the video format may be in
the PAL system. To change the video format,
perform the following:
1. Press the display menu button.
2. Press the down arrow button to highlight the
Video Format option.
3. Press the enter button to select Video Format.
4. Press the right or left arrow button to select
the desired video format.
5. Press the enter button to accept the change.
Audio Output
Audio from the DVD player or auxiliary inputs may
be heard through the following possible sources:
Wireless Headphones
Vehicle Speakers
Vehicle wired headphone jacks on the Rear
Seat Audio system (if equipped)
245
ProCarManuals.com