2007 RENAULT SCENIC lock

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-18V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09
DF021
PRESENT
PROGRAMMING THE STEERING WHEEL ANGLE SENSOR
DEF: Programming not carried out or incorrect
NOTESNotes:
This fault is present for as long as the steering wheel angle is not calibrated.
It is automatically cleared as soon as the programming procedure is completed.
This fault causes an absence of steering wheel recall (with warning light
continuously on).
Place the vehicle on a front axle adjusting bench.
Position the vehicle wheels in the straight line driving position (steering centre point).
Program the steering wheel angle via command VP004 Steering wheel angle sensor programming
(see Configuration and programming, section A).
Vehicle in straight line driving position (steering centre point).
Refer to parameters PR121 Steering wheel angle and PR007 Steering wheel angle offset compensation.
Both parameters must be 0˚.
Turn the steering wheel to full right lock then to full left lock, and check that the parameter varies within the
tolerances given in the conformity check.
Refer to status ET020 Steering wheel angle sensor programming, which must be STATUS 4.
Start the engine and check the operation of the EPAS by turning the steering wheel from lock to lock
(parking manoeuvres).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF021P/DAE_V09_DF021P

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-21V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF035
PRESENT
OR
STOREDVARIABLE POWER ASSISTED STEERING MOTOR
DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock.
Notes:
This fault causes a loss of assistance or an absence of steering assistance and also
illuminates the STOP warning light + Message, or assistance is limited to 30% and
the SERVICE indicator light + Message come on.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 3, 33, 34, 35, 50, 51, 112, 113, 128, 145 of PR143.
Contact Techline.
Procedure to apply for internal fault codes 4, 5, 100, 114, 115, 129, 130 and 131 of PR143.
Check the condition of the wiring inside the EPAS and make sure that the 3 white EPAS connectors are correctly
locked.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF035/DAE_V09_DF035/DAE_V0D_DF035

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-22V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09
DF038
PRESENT
OR
STOREDANGLE SENSOR
1.DEF: Sensor internal electrical fault
2.DEF: Absence of sensor signal
3.DEF: Values outside limits
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock.
Notes:
This fault causes an absence of steering wheel return (no warning light or message).
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 195 and 196 of PR143.
Position the vehicle wheels in the straight line driving position (steering centre point).
Refer to parameters PR121 Steering wheel angle and PR007 Steering wheel angle offset compensation.
Both parameters must be between - 10˚ < X < 10˚.
Turn the steering wheel to full right lock then to full left lock, and check that the parameter varies within the
tolerances given in the "Conformity check".
Refer to status ET020 Steering wheel angle sensor programming, which must be STATUS 4.
If parameters PR121, PR007 and status ET020 are not correct:
Place the vehicle on a front axle adjusting bench.
Position the vehicle wheels in the straight line driving position (steering centre point).
Program the steering wheel angle via command VP004 Steering wheel angle sensor programming (see
Configuration and programming, section A).
Remove the fault, start the engine and check that the EPAS functions correctly by turning the steering wheel from
lock to lock (parking manoeuvres).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF038/DAE_V09_DF038

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-23V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09
DF038
CONTINUED
Procedure to apply for internal fault codes 192, 193 and 194 of PR143.
Check the fault occurrence context for internal fault codes 193 and 194. If PR108 Computer supply voltage
is less than 10 V, the fault is due to a battery undervoltage.
Check the vehicle battery voltage.
Check the tightness and the condition of the battery terminals.
Check the charge circuit if necessary.
Check the condition of the 3 white EPAS connectors and check that they are locked correctly.
In the event of a fault, check the insulation, continuity and the absence of interference resistance on the
following connection:
2-track connector track 1 + 12 V before ignition feed
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-25V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF054
PRESENT
OR
STOREDTORQUE SENSOR
DEF: Sensor internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock, then returning it to the centre.
Notes:
This fault causes:
Loss or absence of steering assistance with STOP warning light + Message
lighting up.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol).
Within these values, parameter PR143 Internal fault code gives the fault finding
procedure to apply.
If, in the fault occurrence context (computer operating values frozen when fault
occurs) PR108 Computer supply voltage is less than 10 V, check the battery
voltage, the tightness and the condition of the battery terminals and check the
charging circuit.
Procedure to apply for internal fault codes 1 and 69 of PR143.
Contact Techline.
Procedure to apply for internal fault codes 48, 66, 64, 65 and 67 of PR143.
Check the condition of the 3 white EPAS connectors and check that they are locked correctly.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF054/DAE_V09_DF054/DAE_V0D_DF054

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-26V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF055
PRESENT
OR
STOREDCOMPUTER MEMORY
DEF: EEPROM irregularity
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock, then returning it to the centre.
Notes:
This fault leads to degraded assistance with no warning light or message or an
assistance that is limited to 10% with the SERVICE indicator light + Message.
–Risk of ESP fault.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 83 and 85 of PR143.
Only for Vdiag 05 and 09:
Check status ET020 Steering wheel angle programming which should be STATUS 4; if not, program the
steering wheel angle sensor VP004 Steering wheel angle programming (see Configuration and
programming).
If the fault is still present after the ignition has been switched on several times, contact the Techline.
Procedure to apply for internal fault codes 84 and 86 of PR143.
Contact Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF055/DAE_V09_DF055/DAE_V0D_DF055

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-27V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF057
PRESENT
OR
STOREDMULTIPLEX VEHICLE SPEED SIGNAL
DEF: Invalid signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Notes:
This fault causes an unsuitable level of assistance and the SERVICE indicator light
+ Message come on.
Carry out fault finding on the multiplex network, and repair if necessary.
Carry out fault finding on the ABS (see 38C, Anti-lock braking system). If the ABS signals no fault and the EPAS
is the only system signalling the fault, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF057/DAE_V09_DF057/DAE_V0D_DF057

POWER-ASSISTED STEERING
Fault finding – Interpretation of statuses
36B
36B-37V5 MR-372-J84-36B000$660_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Interpretation of statuses
ET020
PROGRAMMING THE STEERING WHEEL ANGLE SENSOR
NOTESSpecial note:
–This status is declared correct when it is STATUS 4 (normal mode); in any other
case, apply this fault finding procedure.
–The SERVICE indicator light will come on if the steering wheel angle calibration has
not been carried out.
VARIOUS POSSIBLE STATUS VALUES (with the meaning):
STATUS 1:
–Straight ahead wheel position not programmed.
–Invalid angle value.
PROGRAMMING NOT COMPLETE.STATUS 3:
–Straight ahead wheel position not programmed.
–Invalid angle value.
–Steering wheel out of range ± 120˚ when after ignition
is switched on.
PROGRAMMING COMPLETE, ANGLE TO BE
CONFIRMED.
STATUS 2:
–Straight ahead wheel position not programmed.
–Invalid angle value.
PROGRAMMING NOT COMPLETE.STATUS 4:
–Straight ahead wheel position not programmed.
–Valid angle value.
PROGRAMMING COMPLETE.
STATUS 1 or STATUS 2
If the status is STATUS 1 or STATUS 2, program the steering wheel angle (see Configuration and
programming).
STATUS 3
If the status is STATUS 3, turn the steering wheel from right lock to left lock then slowly return it to slightly beyond
the centre point (PR135 "Column rotation speed" less than 200˚/s). The status should become STATUS 4.
Note:
A present or stored fault can impede STATUS 4 (carry out the necessary operations by referring to the Fault
Finding Manual).
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ET020/DAE_V09_ET020/DAE_V0D_ET020
MR-372-J84-36B000$660_fra.mif