2007 RENAULT SCENIC light

80C-22V2 MR-372-J84-80C000$060.mif
XENON BULBS
Fault finding – Interpretation of faults80C
Program No.: V010
Vdiag No.: 05
AFTER REPAIRTurn on the dipped headlights and check that initialisation is performed.
If there is no initialisation, deal with the system faults.
Adjust the headlights manually after each computer calibration.
Carry out a road test followed by a check with the diagnostic tool.
DF009
CONTINUED 1
1.DEFNOTESNone.
Check the condition of the contacts and connections of the xenon bulb computer and rear height sensor.
Check the continuity and absence of interference resistance between:
Track 6 of the rear level sensor connectorTrack 3 of the xenon bulb computer connector
Track 5 of the rear level sensor connectorTrack 8 of the xenon bulb computer connector
Track 1 of the rear level sensor connector Vehicle earth
If the problem is still present, contact the Techline.
2.DEF
NOTESNone.
Check the condition of the rear sensor linkage and that it is correctly fitted.
Replace if necessary.
Check the condition of the contacts and connections of the xenon bulb computer and rear level sensor.
Check the continuity and absence of interference resistance between:
Track 6 of the rear level sensor connectorTrack 3 of the xenon bulb computer connector
Track 5 of the rear level sensor connectorTrack 8 of the xenon bulb computer connector
Next check the insulation of these connections against earth, and then against + 12 V.
If the problem is still present, contact the Techline.

80C-23V2 MR-372-J84-80C000$060.mif
XENON BULBS
Fault finding – Interpretation of faults80C
Program No.: V010
Vdiag No.: 05
AFTER REPAIRTurn on the dipped headlights and check that initialisation is performed.
If there is no initialisation, deal with the system faults.
Adjust the headlights manually after each computer calibration.
Carry out a road test followed by a check with the diagnostic tool.
DF009
CONTINUED 2
3.DEFNOTESNone.
Check the condition of the rear sensor linkage and that it is correctly fitted.
Replace if necessary.
Check the condition of the contacts and connections of the xenon bulb computer and rear level sensor.
Check the continuity and absence of interference resistance between:
Track 6 of the rear level sensor connectorTrack 3 of the xenon bulb computer connector
Track 5 of the rear level sensor connectorTrack 8 of the xenon bulb computer connector
Next check the insulation of these connections against earth, and then against + 12 V.
If the problem is still present, contact the Techline.
4.DEF
NOTESNone.
Check the condition of the rear sensor linkage and that it is correctly fitted.
Replace if necessary.
Check the condition of the contacts and connections of the xenon bulb computer and rear level sensor.
Check the continuity and absence of interference resistance between:
Track 6 of the rear level sensor connectorTrack 3 of the xenon bulb computer connector
Track 5 of the rear level sensor connectorTrack 8 of the xenon bulb computer connector
Next check the insulation of these connections against earth, and then against + 12 V.
If the problem is still present, contact the Techline.

80C-24V2 MR-372-J84-80C000$060.mif
XENON BULBS
Fault finding – Interpretation of faults80C
Program No.: V010
Vdiag No.: 05
AFTER REPAIRTurn on the dipped headlights and check that initialisation is performed.
If there is no initialisation, deal with the system faults.
Adjust the headlights manually after each computer calibration.
Carry out a road test followed by a check with the diagnostic tool.
DF009
CONTINUED 3
5.DEFNOTESNone.
Check the condition of the rear level sensor linkage.
Replace if necessary.
Check the condition of the contacts and connections of the xenon bulb computer and rear level sensor.
Check the continuity and absence of interference resistance between:
Track 6 of the rear level sensor connectorTrack 3 of the xenon bulb computer connector
Track 5 of the rear level sensor connectorTrack 8 of the xenon bulb computer connector
Next check the insulation of these connections against earth, and then against + 12 V.
If the problem is still present, contact the Techline.

80C-25V2 MR-372-J84-80C000$060.mif
XENON BULBS
Fault finding – Interpretation of faults80C
Program No.: V010
Vdiag No.: 05
AFTER REPAIRTurn on the dipped headlights and check that initialisation is performed.
If there is no initialisation, deal with the system faults.
Adjust the headlights manually after each computer calibration.
Carry out a road test followed by a check with the diagnostic tool.
DF018
PRESENT
OR STOREDACTUATOR1.DEF: Actuator motor fault
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault appears as present after:
–the fault has been cleared,
–the ignition is switched off and on again, then the dipped headlights are switched on.
Park the vehicle facing a wall. Switch off the ignition. Switch on the ignition and turn on the dipped headlights.
Run command AC012 Check actuator high and low positions to make sure that the actuators are working
properly.
Check the lens unit which does not initialise by doing the following.
Check the condition of the computer connections and the actuator connections in the headlights.
Check the continuity and for the absence of interference resistance between:
computer connector track 7track 2 of the actuator connector in the right-
hand headlight
computer connector track 7track 2 of the actuator connector in the right-
hand headlight
Track 1 of the actuator connector vehicle earth
Track 3 of the actuator connector + after ignition feed
If one or more of these checks fails, replace the defective adjustment motor(s).
LAD_V05_DF018

80C-26V2 MR-372-J84-80C000$070.mif
80C
Program No.: V010
Vdiag No.: 05
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Prerequisite: dipped headlights on.
Parameter
or Status Checked
or ActionFunction Display and notes Fault finding
ET001 Computer calibrationCompleted Normal operating mode
Not completed Run CF001 Computer calibration
PR020 Actuator positions15 steps < PR020
< 520 stepsIf the value is incorrect, refer to the
interpretation of fault DF018 Actuator
and run command AC012 Check
actuator high and low position,
to see if they work properly
PR019 Vehicle speed0 mph (0 km/h)
< PR019 < 132 mph
(220 km/h)If the value is incorrect, see the
interpretation of fault
DF001 Computer
LAD_V05_CCONF
XENON BULBS
Fault finding – Conformity check

80C-27V2 MR-372-J84-80C000$070.mif
XENON BULBS
Fault finding – Conformity check80C
Program No.: V010
Vdiag No.: 05
SUB-FUNCTION: LIGHTING POSITION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Prerequisite: dipped headlights on.
Parameter
or Status
Checked
or ActionFunction Display and notes Fault finding
PR017 Front height 8° < PR117 < 115.5°
If the value is incorrect, consult the
interpretation of faults DF008 Front height
sensor circuit and DF009 Rear height
sensor circuit
PR018 Rear height 9° < PR018 < 110°
PR020 Actuator positions15 steps < PR020
< 520 stepsIf the value is incorrect, refer to the
interpretation of fault DF018 Actuator
and run command AC012 Check actuator
high and low position, to see if they work
properly
PR032Front reference
height23° < PR032 < 85.6°
If the value is incorrect, refer to the
interpretation of faults DF008 Front height
sensor circuit and DF009 Rear height
sensor circuit status 4.DEF
PR033Rear reference
height23° < PR032 < 89.5°
PR019 Vehicle speed0 mph (0 km/h)
< PR019 < 132 mph
(220 km/h)If the value is incorrect, see the interpretation
of fault DF001 Computer

80C-28V2 MR-372-J84-80C000$070.mif
XENON BULBS
Fault finding – Conformity check80C
Program No.: V010
Vdiag No.: 05
SUB-FUNCTION: LIGHTING CONTROL
SUB-FUNCTION: LIGHTING MANAGEMENT
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Prerequisite: dipped headlights on.
Parameter or Status
Checked or ActionFunction Display and notes Fault finding
PR020 Actuator positions 15 steps < PR020 < 520 steps If the value is incorrect, refer to
the interpretation of fault
DF018 Actuator and run
command AC012 Check
actuator high and low position,
to see if they work properly
Parameter or Status
Checked or ActionFunction Display and notes Fault finding
ET001 Computer
calibrationCompleted Normal operating mode
Not completed Run CF001 Computer
calibration

80C-34V2 MR-372-J84-80C000$110.mif
80C
Program No.: V010
Vdiag No.: 05
NOTESOnly refer to the customer complaints after a full check with the diagnostic tool.
NO COMMUNICATION WITH THE COMPUTER ALP 1
NO HEIGHT ADJUSTMENT ON EITHER OR BOTH HEADLIGHTS, REGARDLESS
OF VEHICLE LOADALP 2
GLARE OR BEAM TOO HIGHALP 3
THE LEFT AND RIGHT LOW-BEAM HEADLIGHTS DO NOT LIGHT AT THE SAME
HEIGHTALP 4
XENON BULBS
Fault finding – Customer complaints