2007 RENAULT SCENIC warning

AUTOMATIC TRANSMISSION
Fault finding - Introduction
23A
23A - 2V5 MR-372-J84-23A100$058.mif
123A
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. RECAP
Procedure
To run fault finding on the vehicle computers, switch on the ignition.
Proceed as follows:
–Connect the diagnostic tool and perform the required operations. Vehicle(s): MEGANE II and SCENIC II
Function concerned: Automatic transmissionName of computer: Siemens TA 2005
Vdiag No.: 14-18
Special tooling required
Multimeter
Elé. 1681Universal bornier
WARNING
Computer supply for the fault finding procedure:
To run fault finding on the vehicle computers, proceed as follows:
–Place the vehicle's card in the card reader (keyless vehicle scenario 1 (entry level, not hands-free) and
scenario 2 (top of the range, hands-free),
–Press and hold the Start button (more than 5 seconds) outside start-up conditions,
–Then connect the diagnostic tool and perform the required operations.
DP0TA2005_V14_PRELI/DP0TA2005_V18_PRELI
MR-372-J84-23A100$058.mif

AUTOMATIC TRANSMISSION
Fault finding - System operation
23A
23A - 11V5 MR-372-J84-23A100$116.mif
SIEMENS TA2005
Vdiag No.: 14-18
COMPUTER INPUTS AND OUTPUTS
INPUTS OUTPUTS
Diagnostic socket
Automatic
transmission
computer
Solenoid valve control
+ battery feed
+ after ignition feed + warning lights display
Intersystem signals + diagnostic
socketIntersystem signal + diagnostic
socket
Driver actions (brake light switch,
gear selector, multifunction
switch)Gear lever lock
AUTO sensors (turbine speed, oil
pressure, oil temperature)Reversing lights
Earth
Wire connection
Multiplex connection

Fault finding - Configurations and programming23A
23A - 13V5 MR-372-J84-23A100$232.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Configurations and programming
PROGRAMMING
●VP001 Enter VIN:
As it is necessary to enter the VIN each time dialogue is established with the diagnostic tool, it must be
programmed into each vehicle computer whenever a computer is replaced.
Programming procedure:
–Connect the diagnostic tool.
–Consult the fault finding procedure for the automatic transmission.
–Select configuration VP001 Enter VIN.
–Enter the VIN.
–Exit fault finding mode.
–Switch off the ignition.
–Wait for the end of Power-latch: over 10 seconds.
●VP009 Enter last After-Sales operation date:
Every time work is carried out on the automatic transmission in the workshop, enter the date of the
operation.
Select command VP009 Enter last After-Sales operation date on the diagnostic tool, then use the tool's
keypad to enter the date of the operation.
●VP015 Transfer oil condition meter:
Transfer the oil wear counter code from the old computer.
Select command VP015 Transfer oil wear counter on the diagnostic tool, then use the keypad to enter
the code found on the replaced computer.
●VP016 Enter gearbox oil service date:
Select command VP016 Enter gearbox oil service date on the diagnostic tool, then use the keypad to
enter the date found on the replaced computer.
* The immobiliser warning light will flash a few seconds after the ignition is switched off.
MR-372-J84-23A100$232.mif

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A-59V5 MR-372-J84-23A100$406.mif
SIEMENS TA2005
Vdiag No.: 14-18
* The immobiliser warning light will flash for a few seconds after the ignition is switched off.DF232
PRESENT
OR
STORED
COMPUTER
1.DEF: Internal electronic fault
NOTESSpecial note:
The fault relates to an internal computer fault.
If the fault is stored, clear the fault from the computer memory.
Switch off the ignition, wait until the end of power latch* then switch the ignition back on and re-establish dialogue:
Check for + 12 V on connection AP4 of component 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check for earth on connection N of component 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the problem is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
DP0TA2005_V14_DF232/DP0TA2005_V18_DF232

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A-60V5 MR-372-J84-23A100$406.mif
SIEMENS TA2005
Vdiag No.: 14-18
* The immobiliser warning light will flash for a few seconds after the ignition is switched off.DF233
PRESENT
OR
STORED
COMPUTER
1.DEF: Internal electronic fault
NOTESSpecial note:
The fault relates to an internal computer fault.
If the fault is stored, clear the fault from the computer memory.
Switch off the ignition, wait until the end of power latch* then switch the ignition back on and re-establish dialogue:
Check for + 12 V on connection AP4 of component 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check for earth on connection N of component 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the problem is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
DP0TA2005_V14_DF233/DP0TA2005_V18_DF233

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A-61V5 MR-372-J84-23A100$406.mif
SIEMENS TA2005
Vdiag No.: 14-18
* The immobiliser warning light will flash a few seconds after the ignition is switched off.DF234
PRESENT
OR
STORED
COMPUTER
1.DEF: Internal electronic fault
NOTESSpecial note:
The fault relates to an internal computer fault.
If the fault is stored, clear the fault from the computer memory.
Switch off the ignition, wait until the end of power latch* then switch the ignition back on and re-establish dialogue:
Check for + 12 V on connection AP4 of component 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check for earth on connection N of component 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the problem is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
DP0TA2005_V14_DF234/DP0TA2005_V18_DF234