2007 RENAULT SCENIC check engine

Fault finding - Dealing with command modes23A
23A - 125V5 MR-372-J84-23A100$754.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Dealing with command modes
COMMANDS AND CLEARING:
Before using these clearing commands, engine and vehicle speeds must be zero and the selector lever must be in
position P or N.
AC024 Sequential actuator control
This command activates sequence solenoids EVS1 to EVS6 simultaneously to check that they operate correctly.
RZ004 Fault memory
This command clears present and stored faults from the automatic transmission computer.
RZ005 Self-adapting programs
This command is used to clear the automatic transmission computer auto-adaptives following reprogramming, or
after transmission components have been replaced.
After running this command, carry out a road test with the vehicle before returning it to the customer. This is because
the automatic transmission may malfunction during the time taken for the self-adapting programs to re-install.
AFTER REPAIRRepeat the conformity check from the start.
MR-372-J84-23A100$754.mif

Fault finding - Interpretation of commands23A
23A - 126V5 MR-372-J84-23A100$812.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Interpretation of commands
AC024
ACTUATOR SEQUENTIAL CONTROL
NOTESCheck the 30 A permanent computer supply fuse in the Protection and Switching Unit.
Check the 5 A computer after ignition feed fuse in the Protection and Switching Unit.
Replace the fuses if necessary.
Check the cleanliness and condition of the connections.
Engine speed zero and gear lever in position P or N.
This command enables all the automatic transmission solenoid valve actuators to be operated.
Check the insulation, continuity and absence of interference resistance on the following connections:
●connection code 5DN, between components 119 and 1019,
●connection code 5BA, between components 119 and 754,
●connection code 5AU, between components 119 and 754.
If any of the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Control of solenoid valve EVS1:
●connection code 5AV, between components 119 and 754.
Control of solenoid valve EVS2:
●connection code 5AW, between components 119 and 754.
Control of solenoid valve EVS3:
●connection code 5AX, between components 119 and 754.
Control of solenoid valve EVS4:
●connection code 5AY, between components 119 and 754.
Control of solenoid valve EVS5:
●connection code 5DL, between components 119 and 754.
Control of solenoid valve EVS6:
●connection code 5DM, between components 119 and 754.
If any of the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Test the solenoid valves then check for faults on the computer.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_AC024/DP0TA2005_V18_AC024
MR-372-J84-23A100$812.mif

Fault finding - Customer complaints23A
23A - 127V5 MR-372-J84-23A100$870.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Customer complaints
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
NO DIALOGUE WITH THE COMPUTER ALP1
ENGINE STARTING FAULTSALP2
AUTOMATIC TRANSMISSION OPERATING FAULTS ALP3
AUTOMATIC TRANSMISSION MALFUNCTIONING ON GEAR CHANGING ALP4
ERRATIC GEAR CHANGESALP5
REVERSING LIGHTS DO NOT WORK ALP6
OIL UNDER THE VEHICLEALP7
MR-372-J84-23A100$870.mif

Fault finding - Fault Finding Chart23A
23A -128V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart
ALP1 No dialogue with the computer
NOTESNone.
Try the diagnostic tool on another vehicle.
Check:
–the connection between the diagnostic tool and the diagnostic socket (connection and cable in good condition),
–the power supply to the computer,
–the engine and passenger compartment fuses.
Check that the CLIP sensor is supplied by connections BP32, MAN and NAM of component 225, displayed when
both red indicator lights on the sensor illuminate.
Make sure that the CLIP sensor is connected to the computer's USB port.
Make sure the CLIP sensor is communicating properly with the vehicle's computers; this can be seen by the two
green diodes on the sensor lighting up.
Check the following connections on component 225:
●connection code AP43 (+ after ignition feed),
●connection code BP32 (+ battery feed),
●connection code MAN (earth).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Disconnect the automatic transmission computer connector to check the insulation, continuity and the absence
of interference resistance of the following connections:
●connection code AP4, between components 119 and 1337,
●connection code BP42, between components 119 and 1337,
●connection code N, between components 119 and 107,
●connection code 3MT, between components 119 and 120,
●connection code 3MS, between components 119 and 120,
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP01/DP0TA2005_V18_ALP01
MR-372-J84-23A100$928.mif

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -129V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP2 Engine starting faults
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Make sure that the diagnostic tool report, gear lever positions and instrument panel all indicate the same gear
engaged.
Adjust the gear lever cable if it is faulty.
The engine will only start when the gear lever is at P or N.
Check the battery charge and the condition of the terminals (oxidation).
Check the multifunction switch mounting and that it is working.
Check the gear lever control cable and adjust if necessary (see MR 364 Mechanical, 23A, Automatic
transmission, Multifunction switch, Removal - Refitting (for Mégane II) and MR 370 Mechanical, 23A,
Automatic transmission, Multifunction switch, Adjustment (for Scénic II)).
Ensure that the ignition switch is working properly.
Check the power circuit of the starter relay and the starter.
Carry out fault finding on the injection system.
If the engine still doesn't start, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP02/DP0TA2005_V18_ALP02

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -130V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
Start with the ALP1 cycle
ALP3 Automatic transmission operating faults
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
If the engine races when shifting from 1/2 when cold (automatic transmission oil
temperature less than 15˚C), replace the pressure modulating solenoid valve
(EVM).
Use the diagnostic tool to check the
consistency between the display and the gear
lever positions (ignition on and engine
stopped).Adjust the control settings following the
instructions provided (see MR 370, Mechanical,
23 A, Automatic Transmission, Automatic
transmission control unit (for Mégane II and
Scénic II)).
Are they consistent?
Check the oil level and the condition of the oil
(colour, odour, etc.).Replace the automatic transmission (see MR 364,
Mechanical, 23A, Automatic transmission,
Removal-Refitting (for Mégane II) and MR 370,
Mechanical, 23A, Automatic transmission,
Removal-Refitting (for Scénic II)). Does the condition of the oil suggest there
is an internal fault in the automatic
transmission?
With the engine stopped, check the line
pressure information provided by the pressure
sensor (PR003 Oil pressure).Replace the pressure sensor (see MR 364,
Mechanical, 23A, Automatic transmission,
Pressure sensor (for Mégane II) and MR 370,
Mechanical, 23A, Automatic transmission,
Pressure sensor (for Scénic II)).
Is the value higher than 0.2 bar?
NO
YES
YES
NO
YES
NO
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP03/DP0TA2005_V18_ALP03

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -131V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP3
CONTINUED 1
Check the oil level.
Check the oil pressure using PR003 Oil pressure:
Warm engine with gearbox oil temperature between 65 and 90˚C.
Measure the line pressure under the 3 following conditions:
IMPORTANT
The vehicle must be stationary: handbrake on and brake pedal depressed, no accessories operating
(e.g.: air conditioning)
1engine speed idling:
Shift the gear lever to R, N and D, the pressure reading must be greater than 2.5 bars.
2engine speed at 1200 rpm:
–gear lever in R position, the pressure reading must be greater than 4 bars.
–gear lever in D position, the pressure reading in first gear must be greater than 5.5 bars.
3engine speed at 2200 rpm:
–gear lever in R position, the pressure reading must be greater than 11 bars.
–gear lever in D position, the pressure reading in first gear must be greater than 11 bars.
Do the recorded values correspond to the specified values?
Shift the gear lever into position D and monitor
PR007 Turbine speed when accelerating.Replace the pressure modulating solenoid valve
and the oil. Repeat the check after replacement.
If the fault is still present, replace the hydraulic
distributor and all the solenoid valves (see MR 364
Mechanical, 23A, Automatic transmission,
Hydraulic distributor (for Mégane II) and MR 370
Mechanical, 23A, Automatic transmission,
Hydraulic distributor (for Scénic II)).
Does the turbine speed change?

Replace the automatic transmission (see MR 364, Mechanical, 23A,
Automatic transmission, Removal-Refitting (for Mégane II) and MR
370, Mechanical, 23A, Automatic transmission, Removal-Refitting
(for Scénic II)).
A
YESNO
NOYES
B
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -132V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP3
CONTINUED 2
Refer to the procedure and the safety instructions for carrying out a setting point check on the torque converter.
Theoretical engine speed at setting point: 2300 ± 150 rpm
Is the value of the setting point wrong or is there an internal noise in the converter?
Carry out a road test, observing the engine speed
on the instrument panel and the information
displayed on the diagnostic tool (PR006 Engine
speed)Replace the torque converter, the lock-up solenoid
valve and the oil. If the oil is burnt, also replace the
hydraulic distributor and all the solenoid valves
(see MR 364 Mechanical, 23A, Automatic
transmission, Hydraulic distributor
(for Mégane II) and MR 370 Mechanical, 23A,
Automatic transmission, Hydraulic distributor
(for Scénic II)).
When replacing the torque converter, ensure that the
reaction shaft is securely attached to the hub of the
oil pump (flanged shaft).
Note:
A setting point which is too low may be due to a lack
of engine power. Does the engine speed change each time
there is a gear change?

The checks carried out have not provided any
evidence of a fault and the automatic
transmission appears to be working correctly.
If the vehicle does show the customer complaint
selected, continue with the entire fault finding
procedure.Replace the hydraulic distributor and all the solenoid
valves. (see MR 364 Mechanical, 23A, Automatic
transmission, Hydraulic distributor
(for Mégane II) and MR 370 Mechanical, 23A,
Automatic transmission, Hydraulic distributor
(for Scénic II)).
B
NO
NOYES
YESNO
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.