2007 PONTIAC VIBE flat tire

Windshield Wiper Blade Replacement....... 321
Tires............................................................ 322
Tire Sidewall Labeling............................... 323
Tire Terminology and Denitions............... 326
Ination - Tire Pressure............................. 329
Tire Pressure Monitor System................... 330
Tire Inspection and Rotation...................... 333
When It Is Time for New Tires.................. 335
Buying New Tires...................................... 336
Different Size Tires and Wheels................ 337
Uniform Tire Quality Grading..................... 338
Wheel Alignment and Tire Balance............ 339
Wheel Replacement.................................. 340
Tire Chains............................................... 341
If a Tire Goes Flat.................................... 342
Changing a Flat Tire................................. 343
Removing the Spare Tire and Tools.......... 344
Removing the Flat Tire and Installing the
Spare Tire............................................. 346
Storing a Flat or Spare Tire and Tools...... 351
Compact Spare Tire.................................. 354Appearance Care........................................ 354
Cleaning the Inside of Your Vehicle.......... 354
Fabric/Carpet............................................. 356
Leather...................................................... 356
Instrument Panel, Vinyl, and Other
Plastic Surfaces..................................... 357
Care of Safety Belts.................................. 357
Weatherstrips............................................ 358
Washing Your Vehicle............................... 358
Cleaning Exterior Lamps/Lenses................ 358
Finish Care............................................... 358
Windshield, Backglass, and
Wiper Blades......................................... 359
Aluminum Wheels...................................... 359
Tires......................................................... 360
Sheet Metal Damage................................. 360
Finish Damage.......................................... 361
Underbody Maintenance............................ 361
Chemical Paint Spotting............................ 361
Vehicle Care/Appearance Materials............ 362
Section 5 Service and Appearance Care
270

(E) Uniform Tire Quality Grading (UTQG):Tire
manufacturers are required to grade tires
based on three performance factors: treadwear,
traction and temperature resistance. For more
information seeUniform Tire Quality Grading on
page 338.
(F) Maximum Cold Ination Load
Limit:Maximum load that can be carried and the
maximum pressure needed to support that
load. For information on recommended tire
pressure seeInation - Tire Pressure on page 329
andLoading Your Vehicle on page 253.
(A) Temporary Use Only:The compact spare
tire or temporary use tire has a tread life of
approximately 3,000 miles (5 000 km) and should
not be driven at speeds over 65 mph (105 km/h).
The compact spare tire is for emergency use when
a regular road tire has lost air and gone at.
SeeCompact Spare Tire on page 354andIf a
Tire Goes Flat on page 342.
Compact Spare Tire Example
324

This light, on the
instrument panel cluster,
comes on when the
tire pressure monitoring
system detects a
low-tire condition.
This light also comes on for a few seconds and
then go off when you turn the ignition to ON. This
indicates that the TPMS is functioning properly.
If the low-tire pressure warning light comes
on while driving your vehicle, the system may
have detected a low-tire condition. You need to
stop as soon as possible and check your tires
for damage. If a tire is at, seeIf a Tire Goes Flat
on page 342andChanging a Flat Tire on
page 343. Also check the tire pressure in all four
tires, and set them to the specied level shown
on the Tire and Loading Information label.SeeInation - Tire Pressure on page 329and
Loading Your Vehicle on page 253for additional
information.
Note:The tire pressure monitoring system on your
vehicle warns you when one of the tires is
signicantly under-inated and when some
combinations of the tires are signicantly
under-inated. However, there are other
combinations of signicantly under-inated tires for
which the tire pressure monitoring system might not
give a warning. These other combinations are
relatively common, accounting for approximately
half the instances in which vehicles have
signicantly under-inated tires. For example, the
system might not warn you when both tires on the
same side or on the same axle of your vehicle are
signicantly under-inated. It is particularly
important, therefore, to check the tire pressure in all
of the tires regularly and maintain proper pressure.
In order for the tire pressure monitoring system to
work properly you need to reset (initialize) the
tire pressure monitoring system. Any time
you check and/or adjust a tire’s pressure, repair or
replace a tire or wheel, or rotate the tires the
tire pressure monitor system needs to be reset.
331

When rotating your tires, always use the correct
rotation pattern shown here.
Tires should only be moved from front to rear and
rear to front on the same side of the vehicle.
Do not include the compact spare tire in your tire
rotation.
After the tires have been rotated, adjust the front
and rear ination pressures to the amounts
shown on the Tire and Loading Information label.Make certain that all wheel nuts are properly
tightened. See “Wheel Nut Torque” under
Capacities and Specications on page 369.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When
you change a wheel, remove any rust or
dirt from places where the wheel attaches
to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt
off. SeeChanging a Flat Tire on page 343.
Vehicles equipped with a tire pressure monitoring
system will need to reset (initialize) the system
after each tire rotation. SeeTire Pressure Monitor
System on page 330.
334

Wheel Replacement
Replace any wheel that is bent, cracked, or badly
rusted or corroded. If wheel nuts keep coming
loose, the wheel, wheel bolts, and wheel
nuts should be replaced. If the wheel leaks air,
replace it (except some aluminum wheels,
which can sometimes be repaired). See your
dealer if any of these conditions exist.
Your dealer will know the kind of wheel you need.
Each new wheel should have the same
load-carrying capacity, diameter, width, offset
and be mounted the same way as the one
it replaces.
If you need to replace any of your wheels, wheel
bolts, or wheel nuts, replace them only with
new GM original equipment parts. This way, you
will be sure to have the right wheel, wheel
bolts, and wheel nuts for your vehicle.{CAUTION:
Using the wrong replacement wheels,
wheel bolts, or wheel nuts on your vehicle
can be dangerous. It could affect the
braking and handling of your vehicle,
make your tires lose air and make you
lose control. You could have a collision in
which you or others could be injured.
Always use the correct wheel, wheel bolts,
and wheel nuts for replacement.
Notice:The wrong wheel can also cause
problems with bearing life, brake cooling,
speedometer or odometer calibration,
headlamp aim, bumper height, vehicle ground
clearance, and tire or tire chain clearance
to the body and chassis.
SeeChanging a Flat Tire on page 343for more
information.
340

If a Tire Goes Flat
It is unusual for a tire to blowout while you are
driving, especially if you maintain your vehicle’s
tires properly. If air goes out of a tire, it is
much more likely to leak out slowly. But if you
should ever have a blowout, here are a few tips
about what to expect and what to do:
If a front tire fails, the at tire will create a drag
that pulls the vehicle toward that side. Take your
foot off the accelerator pedal and grip the
steering wheel rmly. Steer to maintain lane
position, and then gently brake to a stop well out
of the traffic lane.
A rear blowout, particularly on a curve, acts much
like a skid and may require the same correction
you would use in a skid. In any rear blowout
remove your foot from the accelerator pedal. Get
the vehicle under control by steering the way
you want the vehicle to go. It may be very bumpy
and noisy, but you can still steer. Gently brake
to a stop, well off the road if possible.{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
If a tire goes at, the next part shows how to use
the jacking equipment to change a at tire safely.
342

Changing a Flat Tire
If a tire goes at, avoid further tire and wheel
damage by driving slowly to a level place. Turn on
your hazard warning ashers.
{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire. To
help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put an automatic transaxle shift lever
in PARK (P), or shift a manual
transaxle to FIRST (1) or REVERSE (R).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
CAUTION: (Continued)
CAUTION: (Continued)
To be even more certain the vehicle will
not move, you should put blocks at the
front and rear of the tire farthest away
from the one being changed. That would
be the tire on the other side, at the
opposite end of the vehicle.
When you have a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you how to use
the jack and change a tire.
343

Removing the Flat Tire and
Installing the Spare Tire
1. Attach the jack handle to the jack.
2. Turn the jack handle clockwise to raise the lift
head a little.
3. Using the wheel wrench, loosen all the wheel
nuts. Do not remove them yet.4. Position the jack and raise the jack lift head to
t over the car ange between the two
notches.
346