2007 PONTIAC TORRENT flat tire

When It Is Time for New Tires.................. 401
Buying New Tires...................................... 401
Different Size Tires and Wheels................ 403
Uniform Tire Quality Grading..................... 403
Wheel Alignment and Tire Balance............ 405
Wheel Replacement.................................. 405
Tire Chains............................................... 406
If a Tire Goes Flat.................................... 407
Changing a Flat Tire................................. 408
Removing the Spare Tire and Tools.......... 409
Removing the Flat Tire and Installing the
Spare Tire............................................. 411
Storing a Flat or Spare Tire and Tools...... 418
Compact Spare Tire.................................. 420
Appearance Care........................................ 420
Cleaning the Inside of Your Vehicle.......... 420
Fabric/Carpet............................................. 422
Leather...................................................... 423
Instrument Panel, Vinyl, and Other Plastic
Surfaces................................................ 424
Care of Safety Belts.................................. 424
Weatherstrips............................................ 425Washing Your Vehicle............................... 425
Cleaning Exterior Lamps/Lenses................ 425
Finish Care............................................... 425
Windshield and Wiper Blades.................... 426
Aluminum or Chrome-Plated Wheels......... 426
Tires......................................................... 427
Sheet Metal Damage................................. 427
Finish Damage.......................................... 428
Underbody Maintenance............................ 428
Chemical Paint Spotting............................ 428
Vehicle Care/Appearance Materials............ 429
Vehicle Identication.................................. 430
Vehicle Identication Number (VIN)........... 430
Service Parts Identication Label............... 430
Electrical System........................................ 431
Add-On Electrical Equipment..................... 431
Windshield Wiper Fuses............................ 431
Fuses and Circuit Breakers....................... 431
Instrument Panel Fuse Block..................... 432
Engine Compartment Fuse Block............... 434
Capacities and Specications.................... 436
Section 5 Service and Appearance Care
338

(D) Tire Identication Number (TIN):The letters
and numbers following DOT (Department of
Transportation) code is the Tire Identication
Number (TIN). The TIN shows the manufacturer
and plant code, tire size, and date the tire
was manufactured. The TIN is molded onto both
sides of the tire, although only one side may have
the date of manufacture.
(E) Tire Ply Material:The type of cord and
number of plies in the sidewall and under the tread.
(F) Uniform Tire Quality Grading (UTQG):Tire
manufacturers are required to grade tires
based on three performance factors: treadwear,
traction, and temperature resistance. For more
information seeUniform Tire Quality Grading
on page 403.
(G) Maximum Cold Ination Load
Limit:Maximum load that can be carried and the
maximum pressure needed to support that load.(A) Temporary Use Only:The compact spare
tire or temporary use tire has a tread life of
approximately 3,000 miles (5 000 km) and should
not be driven at speeds over 65 mph (105 km/h).
The compact spare tire is for emergency use when
a regular road tire has lost air and gone at. If
your vehicle has a compact spare tire, see
Compact Spare Tire on page 420andIf a Tire
Goes Flat on page 407.
Compact Spare Tire Example
388

Do not include the compact spare tire in your tire
rotation.
After the tires have been rotated, adjust the
front and rear ination pressures as shown on
the Tire and Loading Information label. See
Ination - Tire Pressure on page 393andLoading
Your Vehicle on page 321.
Reset the Tire Pressure Monitor System. See
“TPMS Sensor Matching Process” under
Tire Pressure Monitor System on page 395.
Make certain that all wheel nuts are properly
tightened. See “Wheel Nut Torque” under
Capacities and Specications on page 436.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When
you change a wheel, remove any rust or
dirt from places where the wheel attaches
to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt
off. SeeChanging a Flat Tire on page 408.
400

Notice:The wrong wheel can also cause
problems with bearing life, brake cooling,
speedometer or odometer calibration,
headlamp aim, bumper height, vehicle ground
clearance, and tire or tire chain clearance
to the body and chassis.
SeeChanging a Flat Tire on page 408for more
information.
Used Replacement Wheels
{CAUTION:
Putting a used wheel on your vehicle is
dangerous. You cannot know how it has
been used or how far it has been driven. It
could fail suddenly and cause a crash. If
you have to replace a wheel, use a new
GM original equipment wheel.
Tire Chains
{CAUTION:
Do not use tire chains. There is not enough
clearance. Tire chains used on a vehicle
without the proper amount of clearance
can cause damage to the brakes,
suspension or other vehicle parts. The area
damaged by the tire chains could cause
you to lose control of your vehicle and you
or others may be injured in a crash.
Use another type of traction device only if
its manufacturer recommends it for use on
your vehicle and tire size combination and
road conditions. Follow that
manufacturer’s instructions. To help avoid
damage to your vehicle, drive slowly,
readjust or remove the device if it is
contacting your vehicle, and do not spin
your vehicle’s wheels. If you do nd
traction devices that will t, install them on
the front tires.
406

If a Tire Goes Flat
It is unusual for a tire to blowout while you are
driving, especially if you maintain your vehicle’s
tires properly. If air goes out of a tire, it is
much more likely to leak out slowly. But if you
should ever have a blowout, here are a few tips
about what to expect and what to do:
If a front tire fails, the at tire will create a drag
that pulls the vehicle toward that side. Take your
foot off the accelerator pedal and grip the
steering wheel rmly. Steer to maintain lane
position, and then gently brake to a stop well out
of the traffic lane.
A rear blowout, particularly on a curve, acts much
like a skid and may require the same correction
you would use in a skid. In any rear blowout
remove your foot from the accelerator pedal. Get
the vehicle under control by steering the way
you want the vehicle to go. It may be very bumpy
and noisy, but you can still steer. Gently brake
to a stop, well off the road if possible.{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
If a tire goes at, the next part shows how to use
the jacking equipment to change a at tire safely.
407

Changing a Flat Tire
If a tire goes at, avoid further tire and wheel
damage by driving slowly to a level place. Turn on
your vehicle’s hazard warning ashers. See
Hazard Warning Flashers on page 150for more
information.{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire. To
help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
To be even more certain the vehicle will
not move, you should put blocks at the
front and rear of the tire farthest away
from the one being changed. That would
be the tire, on the other side, at the
opposite end of the vehicle.
408

Removing the Flat Tire and
Installing the Spare Tire
You must take off the wheel cover or center cap, if
the vehicle has one, to reach the wheel bolts.
1. Loosen all ve
plastic caps by
turning the wheel
wrench
counterclockwise.
Do not try to remove
plastic caps from
the cover or
center cap.
2. Pull the cover or center cap away from the
wheel.
3. Use the wheel wrench to loosen all the wheel
nuts. Do not remove them yet.4. Attach the wheel wrench to the jack bolt head
and turn the wheel wrench clockwise. That
will raise the lift head a little.
5. Place the jack near the at tire.
Notice:Make sure that the jack lift head is in
the correct position or you may damage
your vehicle. The repairs would not be covered
by your warranty.
411

Notice:Wheelcovers will not t on your
compact spare. If you try to put a wheel cover
on the compact spare, you could damage
the cover or the spare.
Do not try to put a wheel cover on your compact
spare tire. It will not t. Store the wheel cover in the
cargo area until you have the at tire repaired or
replaced.
Storing a Flat or Spare Tire and
Tools
{CAUTION:
Storing a jack, a tire, or other equipment
in the passenger compartment of the
vehicle could cause injury. In a sudden
stop or collision, loose equipment could
strike someone. Store all these in the
proper place.To store the at tire or the spare tire and tools, do
the following:
1. Place the wheel wrench into the bag.
2. Use the hook and loop fastener straps to
secure the bag to the jack.
3. Install the jack in the
left side panel of
cargo area and
secure it with the
wing bolt.
4. Remove the wheel stow rod from the left side
of the oor compartment.
418