2007 PONTIAC GRAND PRIX instrument panel

The main components of the instrument panel are the following:
A. Side Window Defogger Outlets. SeeOutlet
Adjustment on page 166.
B. Air Outlets. SeeOutlet Adjustment on page 166.
C. Turn Signal/Multifunction Lever and Cruise
Controls. SeeTurn Signal/Multifunction Lever
on page 135andCruise Control on page 140.
D. TAP-Shift
®Control (If Equipped). See
Automatic Transaxle Operation on page 110.
E. Hazard Warning Flashers Button. See
Hazard Warning Flashers on page 134.
F. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 169.
G. Windshield Wiper Lever. SeeWindshield Wiper
Lever on page 138.
H. Ignition. SeeIgnition Positions on page 105.
I. Driver Information Center (DIC) (If Equipped).
SeeDriver Information Center (DIC) on
page 186.
J. Audio System. SeeAudio System(s) on
page 233.K. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 277.
L. Hood Release. SeeHood Release on page 345.
M. Tilt Steering Wheel Lever, on Steering Column.
SeeTilt Wheel on page 135.
N. Interior Lamps Brightness Control. SeeInterior
Lamps on page 146.
O. Passenger Air Bag Status Indicator. See
Passenger Airbag Status Indicator on page 173.
P. Climate Controls. SeeClimate Control
System on page 157.
Q. Shift Lever. SeeAutomatic Transaxle Operation
on page 110.
R. Traction Control Button (If Equipped). See
Traction Control System (TCS) on page 292.
S. Head Up Display (HUD) Control (If Equipped).
SeeHead-Up Display (HUD) on page 151.
T. Glove Box. SeeGlove Box on page 126.
U. Instrument Panel Fuse Block. SeeInstrument
Panel Fuse Block on page 460.
133

Flash-to-Pass Feature. SeeFlash-to-Pass on
page 137.
ICruise Control. SeeCruise Control on
page 140.
PExterior Lamps Control. SeeExterior
Lamps on page 144.
Turn and Lane-Change Signals
To signal a turn, move the turn signal lever located
on the left side of the steering column all the
way up or down. The lever returns automatically
when the turn is complete.
An arrow on the
instrument panel cluster
will ash in the
direction of the turn or
lane change.
If the vehicle is equipped with the Head-Up-Display
(HUD), a right or left turn signal will appear in
the HUD area when making turns or lane changes.
SeeHead-Up Display (HUD) on page 151for
more information.Raise or lower the lever until the arrow starts to
ash to signal a lane change. Hold it there until the
lane change is complete. The lever returns to its
original position when it is released.
Arrows that ash rapidly when signaling for a turn
or lane change may be caused by a burned-out
signal bulb. Other drivers will not see the signal.
Replace burned-out bulbs to help avoid possible
accidents. SeeReplacement Bulbs on page 398,
Front Turn Signal, Parking and Fog Lamps on
page 394, andTaillamps, Turn Signal, and
Stoplamps on page 395. Also, check the fuse for
burned-out bulbs if a turn signal arrow fails to
work when signaling a turn. SeeFuses and Circuit
Breakers on page 460for location information.
Turn Signal On Chime
If the turn signal is left on for more than
0.75 of a mile (1.21 km), a warning chime will
sound and the TURN SIGNAL ON warning
message will appear on the Driver Information
Center (DIC) display. See “Turn Signal On” under
DIC Warnings and Messages on page 200.
136

Headlamp High/Low-Beam Changer
Push forward on the exterior lamps control
lever to change the headlamps from low to
high-beam. Pull the lever back and then release it
to change from high to low-beam.
This symbol appears on
the instrument panel
cluster when the
high-beam headlamps
are on.
When the high-beam headlamps are on, the fog
lamps will not be on. If the vehicle is equipped with
the Head-Up-Display (HUD) an arrow will appear
in the HUD area indicating that the high-beams
are on. SeeHead-Up Display (HUD) on page 151
for more information.
Flash-to-Pass
This feature allows the use of the high-beam
headlamps to signal the driver in front of you that
you want to pass.
Pull and hold the exterior lamps control lever to
use this feature. When this is done, the following
will occur:
The high-beam headlamps will turn on, while
the headlamps are off, in low-beam, or in
Daytime Running Lamps (DRL) mode. They
will stay on as long as the lever is held in this
position. Release the lever to turn them off.
The headlamps will switch to low beam if the
headlamps had been in the high-beam
mode. To return to high-beam, push the lever.
If the vehicle is equipped with the Head-Up Display
(HUD), an arrow will appear on the display to
indicate that the high beams are on.
137

6(Low Speed):Push the lever up to the
second position for steady wiping cycles at a slow
speed.
1(High Speed):Push the lever up to the
third position for steady wiping cycles at a high
speed.
7(Mist):For a single wiping cycle, push the
lever down once and let go. The wipers will
stop after one cycle. For additional cycles, hold
the lever down.
About 30 seconds after the wipers are on, the
headlamps, taillamps, and instrument panel
lighting will come on, and the Driver Information
Center (DIC) back lighting will decrease to
the night time mode. About ten seconds after the
wipers are turned off, all the lamps will go back
to the AUTO (Automatic) mode. SeeExterior
Lamps on page 144.
Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
The windshield washer button is located at the
end of the windshield wiper lever.
K(Washer Fluid):Press this button to activate
the washer uid to spray onto the windshield.
The wipers will run for a few cycles to clear the
windshield. For more wash cycles, press and hold
the button.
If the vehicle is low on washer uid, the LOW
WASHER FLUID message will appear on
the Driver Information Center (DIC) display. See
“LOW WASHER FLUID” underDIC Warnings
and Messages on page 200for more information.
139

The CRUISE SET message will also appear
briey on the Head-Up Display (HUD), if your
vehicle has one, when the cruise control lever is
pushed to the minus (set) or the plus
(resume/accelerate) positions.
A cruise control light will also appear on the
instrument panel cluster when the cruise control is
on. This light will disappear when the brakes
are applied or the cruise control is cancelled. It will
reappear when the set cruise speed is resumed.
The light will go out when the cruise control is
turned off. SeeCruise Control Light on page 185.
Resuming a Set Speed
Once you are going about 25 mph (40 km/h) or
more, you can move the cruise control switch
briey from on to resume/accelerate.
Your vehicle will go back up to your previously
chosen speed and stay there.
If you hold the switch at resume/accelerate the
vehicle will keep going faster until you release the
switch or apply the brake. Do not hold the
switch at resume/accelerate, unless you want the
vehicle to go faster.
Increasing Speed While Using
Cruise Control
There are two ways to go to a higher speed:
Use the accelerator pedal to get to the higher
speed. Press the set button at the end of the
lever, then release the button and the
accelerator pedal. You will now cruise at the
higher speed. If the accelerator pedal is
held longer than 60 seconds, cruise control
will turn off.
Move the cruise switch from on to resume/
accelerate. Hold it there until you get up to the
speed desired, and then release the switch.
To increase the vehicle speed in very small
amounts, move the switch briey to resume/
accelerate. Each time you do this, your vehicle
will go about 1 mph (1.6 km/h) faster.
The acceleration feature will only work after the
cruise control speed has been set by pushing the
cruise control set button.
142

Exterior Lamps
The exterior lamp control is located to the left of
the steering wheel on the multifunction lever.
O(Exterior Lamp Control):Turn the band with
this symbol on it to operate the exterior lamps.
The exterior lamp band has four positions:
O(Off):Turning the band to this position turns
off all lamps.
AUTO (Automatic):Turning the band to this
position sets the exterior lamps in automatic mode.
AUTO mode will turn the exterior lamps on and
off depending on how much light is available
outside the vehicle.To override AUTO mode, turn the control to off.
To reset to AUTO mode turn the control to exterior
lamps and then back to AUTO. Automatic mode
will also reset when your vehicle is turned off
and then back on again when the control is left in
the AUTO position.
;(Parking Lamp):Turning the band to this
position turns on the parking lamps together with
the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
The parking brake indicator light will come on and
stay on when the parking lamps are on with the
engine off and the ignition to ACC.
5(Headlamps):Turning the control to this
position turns on the headlamps, together with the
previously listed lamps and lights.
144

Headlamps on Reminder
A warning chime will sound if the vehicle’s ignition
is off and the driver’s door is opened when the
exterior lamp control is left on in either the
headlamp or parking lamp position.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Daytime running lamps are required to
function at all times on all vehicles rst sold
in Canada.
A light sensor on top of the instrument panel
makes the DRL work, so be sure it is not covered.
The DRL system will make the low-beam
headlamps come on at reduced brightness when
the following conditions are met:
The ignition is on.
The exterior lamps control is off.
The parking brake is released.While the DRL are on, only the vehicle’s low-beam
headlamps will be on at reduced brightness.
The turn signal, taillamps, sidemarker and other
lamps will not be on. The instrument panel cluster
will not be lit up either.
When it is dark enough outside, the DRL will turn
off and the vehicle’s headlamps and parking
lamps will turn on. The other lamps that come on
with the headlamps will also come on.
When it is bright enough outside, the headlamps
will go off and the DRL will come on.
To idle the vehicle with the DRL off, turn the
exterior lamp control off and then do one of the
following:
Turn the exterior lamp control to the parking
lamp position.
Turn the exterior lamp control to the headlamp
position.
Turn the exterior lamp control from AUTO to
off and back to AUTO.
This feature is not available for vehicles rst sold
in Canada.
145

To turn off the automatic headlamp feature when it
is dark outside, move the exterior lamp control
to the parking lamp position. The parking lamps
will remain illuminated and the headlamps will turn
off. The fog lamps will also go on if they were
on previously.
As with any vehicle, the regular headlamp system
should be turned on when needed.
Fog Lamps
If equipped, fog lamps provide brighter roadway
lighting for better vision in foggy or misty
conditions.
-(Fog Lamps):Turn the second band on the
exterior lamps control lever to this position to
turn the fog lamps on. The band will return to its
original position.
This symbol appears on
the instrument panel
cluster when the
fog lamps are on.To turn the fog lamps off, turn the band up to the
fog lamp symbol and release it. The band will
return to its original position. If the high-beam
headlamps are on, the fog lamps will turn off. The
fog lamps will go on again when the low-beam
headlamps are turned back on.
The parking lamps must be on for the fog lamps
to work.
Some localities have laws that require the
headlamps to be on along with the fog lamps.
Exterior Lighting Battery Saver
If the parking lamps or headlamps have been left
on after the ignition has been turned to off, the
exterior lamps will turn off after about 10 minutes.
This protects the battery from being drained.
Use the exterior lamp control to turn the lamps
back on, if they are still needed.
Interior Lamps
The interior lamps can be controlled, or
automatically turn on or off under certain conditions.
They are explained in the following text.
146