2007 PONTIAC GRAND PRIX clock

9. Inate the tire up to the recommended
ination pressure, found on the Tire and
Loading Information label located on
the vehicle’s center pillar (B-pillar) below the
vehicle’s door latch, using the air pressure
gage on the top of the unit as a guide.
The pressure gage reading is slightly high
while the compressor is on. Turn the
compressor off to get an accurate pressure
reading.
Notice:If the recommended pressure cannot
be reached after 15 minutes, the vehicle
should not be driven farther. Damage to the
tire is severe and the sealant will not be
effective. Remove the air compressor plug
from the accessory power outlet and unscrew
the inating hose from the tire valve. See
Roadside Assistance Program on page 498.10. Move the inator kit switch to the O (off)
position once the correct tire pressure is
obtained.
11. Turn off the engine.
12. Unplug the air compressor accessory plug
from the accessory power outlet in the
vehicle.
13. Disconnect the sealant lling hose from the
tire valve stem, by turning it counterclockwise,
and replace the tire valve stem cap.
Be careful when handling the tire inator
components as they may be hot after usage.
14. Wrap the sealant lling hose around the air
compressor channel to stow it in its original
location.
15. Stow the air compressor accessory plug back
in the air compressor. To do this, wrap the air
compressor accessory plug, snap in the
plug, and then push in the bottom and then
the top of the wrapped air compressor
accessory plug.
429

16. If the at tire was
able to inate to the
recommended
ination pressure,
remove the
maximum speed
label from the
sealant canister.
Place it in a highly visible location such as
the inside of the upper left corner of the
windshield or to the face of the radio/clock.
The maximum speed label reminds you
to drive cautiously and not to exceed
55 mph (90 km/h) until you have the
damaged tire inspected and repaired.
{CAUTION:
Storing the tire inator kit or other
equipment in the passenger compartment
of the vehicle could cause injury. In a
sudden stop or collision, loose equipment
could strike someone. Store the tire
inator kit in the proper place.
17. Return the equipment to the proper storage
location in the trunk of your vehicle.
430

4. Turn the sealant canister so the inator lling
hose is aligned with the slot in the
compressor.5. Lift the sealant canister from the air
compressor and replace with a new sealant
canister. See your GM dealer for more
information.
To install a new sealant canister, do the following:
1. Align the sealant lling hose with the slot in
the air compressor.
2. Push the sealant canister down and turn it
clockwise.
3. Wrap the sealant lling hose around the air
compressor channel to stow it in its original
location.
4. Push the air compressor inator hose onto
the sealant canister inlet and push the
lever down.
434

When your vehicle has a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.Removing the Spare Tire and Tools
The equipment needed to change a tire is
located in the trunk.
1. Open the trunk. SeeTrunk on page 96for
more information.
2. Remove the convenience net, if equipped, by
removing the net hook attachments.
3. Lift up the carpet.
4. Turn the center nut
on the compact
spare tire cover
counterclockwise to
remove it.
5. Remove the cover.
6. Remove the compact spare tire. SeeCompact
Spare Tire on page 447for more information.
436

7. Turn the nut holding the jack counterclockwise
and remove it. Then remove the jack and
wrench.8. The tools you will be using include the
jack (A), extension and protector/guide (B) and
the wheel wrench (C).
437

Removing the Flat Tire and
Installing the Spare Tire
Your vehicle may have aluminum wheels. If so,
you will see exposed stainless steel wheel
nuts. Use the wheel wrench to loosen all the
wheel nuts. Do not remove them yet.
Or, your vehicle may have steel wheel covers.To remove the steel wheel covers and wheel nut
caps, loosen the plastic nut caps with the wheel
wrench in a counterclockwise direction. If needed,
you can nish loosening them with your ngers. The
plastic nut caps will not come off.
Use the at end of the wheel wrench and pry
along the edge of the cover until it comes off. The
edge of the wheel cover could be sharp, so do
not try to remove it with your bare hands. Do not
drop the cover or lay it face down, as it could
become scratched or damaged.
438

{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
5. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off
the ground for the compact spare tire to attach
to the vehicle.
441

9. Reinstall the wheel
nuts with the
rounded end of the
nuts toward the
wheel. Tighten each
nut by hand until
the wheel is
held against
the hub.
10. Lower the vehicle by turning the jack handle
counterclockwise. Lower the jack completely.
443