2007 PONTIAC GRAND PRIX clock

7. Locate the vertical headlamp aiming screws,
which are under the hood, near the
headlamps. Turn the vertical aiming screw
until the headlamp beam is aimed to the
horizontal tape line.
The adjustment screws can be turned with a
6 mm hex key bit socket ora6mmhexkey.8. Turn the vertical aiming screw until the
headlamp beam is aimed to the horizontal
tape line. Turn it clockwise or
counterclockwise to raise or lower the angle
of the beam.
9. Make sure that the light from the headlamp is
positioned at the bottom edge of the horizontal
tape line. The lamp on the left (A) shows
the correct headlamp aim. The lamp on the
right (B) shows the incorrect headlamp aim.
10. Repeat Steps 7 through 9 for the opposite
headlamp.
Driver’s Side shown
390

A. High-Beam Headlamp
B. Low-Beam Headlamp
C. Sidemarker Lamp5. Turn the bulb socket ring one-quarter of a turn
counterclockwise to remove it from the
headlamp assembly.
6. Pull the old bulb from the socket.
7. Place the new bulb into the socket.
8. Turn the bulb socket ring one-quarter turn
clockwise to reinstall it back into the
headlamp assembly.
9. Carefully reinstall the headlamp assembly.
10. Push down on the metal retaining clip
while pushing rearward on the headlamp,
making sure the headlamp assembly is
secure.
11. Reinstall the bolt and tighten to secure.
393

3. Turn the bulb socket one-quarter of a turn
counterclockwise to remove it from its
assembly.
4. Pull the old bulb from the socket and replace
it with a new one.
5. Turn the bulb socket a quarter turn clockwise
to reinstall it.
6. Reinstall the headlamp assembly.
7. Push down on the metal retaining clip while
pushing rearward on the headlamp, making
sure the headlamp assembly is secure.
8. Reinstall the bolt and tighten to secure.Taillamps, Turn Signal, and
Stoplamps
A. Taillamp
B. Taillamps, Turn
Signal and Stoplamps
1. Open the trunk. SeeTrunk on page 96for
more information.
2. Remove the convenience net, if equipped, by
removing the net hook attachments.
3. Remove the plastic cap from the trunk trim.
4. Pull the trunk trim and carpet away from
the back of the trunk.
5. Remove the bottom bolt and two nuts.
395

6. Remove the taillamp
assembly by pulling
it out from the
vehicle.7. Turn the appropriate
lamp socket a
quarter turn
counterclockwise
and remove it.
8. Remove the old bulb.
9. Replace with a new bulb into the socket and
turn the lamp socket clockwise to install it.
10. Reinstall the taillamp assembly by reversing
Steps 2 through 5.
396

Back-Up Lamps
The back-up lamps are located on the trunk lid.
To replace the back-up lamp bulb(s), do the
following:
1. Open the trunk. SeeTrunk on page 96for
more information.
2. Turn the appropriate lamp socket a quarter
turn counterclockwise and remove it.
3. Remove the old bulb.
4. Put the new bulb into the lamp socket.
5. Turn the bulb a quarter turn clockwise to
reinstall it.
397

License Plate Lamp
To replace one of these bulbs, do the following:
1. Open the trunk. SeeTrunk on page 96
2. Turn the appropriate lamp socket a quarter
turn counterclockwise and remove it.
3. Remove the old bulb.
4. Put the new bulb into the lamp socket.
5. Turn the bulb a quarter turn clockwise to
reinstall it.
Replacement Bulbs
Exterior Lamps Bulb Number
Back-Up Lamp 3157
Front Parking/Turn Signal Lamp3757 NAK* or
5702 KA**
Front Sidemarker and License
Plate Lamp194
Headlamps
High-Beam Halogen 9005
Low-Beam Halogen 9006
Stop/Taillamp/Turn Signal Lamps 3057
* GT and Base Models with the Optional Fog Lamps
** For Lamps Not Equipped with the Fog Function and
GXP Models
For replacement bulbs not listed here, contact
your dealer.
398

If the at tire is due to a slow leak caused by a
nail or other similar road hazard, the tire inator
kit may be used to temporarily repair the
damaged tire.
After temporarily repairing a tire using the tire
inator kit, it is recommended to take your vehicle
to an authorized GM dealer within 100 miles
(161 kilometers) of driving to have the tire
inspected and repaired. If the sealant isn’t
removed from the tire within a 100 miles
(161 kilometers) of driving, it is more likely
that the tire and tire pressure monitoring sensor
may get damaged and have to be replaced.Accessing the Tire Inator Kit
To access the tire inator kit, do the following:
1. Open the trunk. SeeTrunk on page 96
for more information.
2. Locate the tire inator kit by lifting up the
carpet.
3. Remove the inator
kit cover by turning
the center nut
counterclockwise.
425

Using the Tire Inator Kit
To use the tire inator kit, do the following:
1. Place the inator kit on the ground and unwrap
the sealant lling hose from the compressor.
2. Remove the air compressor accessory plug
from the unit. To do this, pull the top portion
of the wrapped cord out rst, then the bottom,
then unsnap the plug. Do not insert the
plug into an accessory outlet yet.
3. Remove the valve stem cap from the at tire
by turning it counterclockwise.
If an object, such as a nail, has penetrated the
tire, do not remove it.
4. Attach the sealant lling hose (A) onto the tire
valve stem. Turn it clockwise until it is tight.
Make sure the inator kit on/off switch (B) is in
the O (off) position.
5. Plug the air compressor accessory plug (C)
into an accessory power outlet in the vehicle.
SeeAccessory Power Outlet(s) on page 156
for more information.
427