2007 PONTIAC G6 trunk

{CAUTION:
Things you put inside your vehicle can
strike and injure people in a sudden stop
or turn, or in a crash.
Put things in the trunk or rear area of
your vehicle. In a trunk, put them as
far forward as you can. Try to spread
the weight evenly. If you have
fold-down rear seats, you will nd four
anchors on the back wall of your
trunk. You can use these anchors to
tie down lighter loads. They are not
strong enough for heavy things,
however, so put them as far forward
as you can in the trunk or rear area.
Never stack heavier things, like
suitcases, inside the vehicle so that
some of them are above the tops of
the seats.
CAUTION: (Continued)
CAUTION: (Continued)

Do not leave an unsecured child
restraint in your vehicle.
When you carry something inside the
vehicle, secure it whenever you can.
Do not leave a seat folded down
unless you need to.
Towing
Towing Your Vehicle
Consult your dealer or a professional towing
service if you need to have your disabled vehicle
towed. SeeRoadside Assistance Program on
page 456.
If you want to tow your vehicle behind another
vehicle for recreational purposes (such as behind
a motorhome), see “Recreational Vehicle
Towing” following.
293

Filling a Portable Fuel Container
{CAUTION:
Never ll a portable fuel container while it
is in your vehicle. Static electricity
discharge from the container can ignite
the gasoline vapor. You can be badly
burned and your vehicle damaged if this
occurs. To help avoid injury to you and
others:
Dispense gasoline only into approved
containers.
Do not ll a container while it is inside
a vehicle, in a vehicle’s trunk, pickup
bed, or on any surface other than the
ground.
CAUTION: (Continued)
CAUTION: (Continued)

Bring the ll nozzle in contact with the
inside of the ll opening before
operating the nozzle. Contact should
be maintained until the lling is
complete.
Do not smoke while pumping
gasoline.
315

3. Pull back the front fascia then pull the
headlamp assembly forward, out of the
vehicle. You need to pry the headlamp
assembly away from the fender. This frees
the ball stud from its retainer in the fender
bracket.
You might want someone to assist you with
the removal of the headlamp assembly to avoid
possible damage to the vehicle.
4. Remove the bulb access cover by turning it
counterclockwise.
5. Turn the bulb socket counterclockwise and
pull out the bulb assembly.
6. Disconnect the bulb socket from the wiring
harness for headlamps.
For the front turn signal/parking or sidemarker
bulbs, unclip the bulb from the socket.
7. Install a new bulb.
8. Reverse Steps 1 through 4 to reinstall the
bulb assembly and headlamp assembly.Center High-Mounted
Stoplamp (CHMSL) (Sedan)
To replace a center high-mounted stoplamp
(CHMSL) bulb, do the following:
1. Open the trunk lid. SeeTrunk on page 113for
more information.
2. Locate the center high-mounted stoplamp
(CHMSL) on the inside of the trunk lid.
3. Unclip the wiring harness by using a tool to
disengage the connector.
4. Remove the cover by pressing the tabs at
either end with a tool.
363

To replace one of these bulbs, do the following:
1. Open the trunk. SeeTrunk on page 113
for more information.
2. Remove the convenience net, if the vehicle
has one.
3. Remove the wing nuts holding the trunk trim.
4. Remove the two nuts, which hold the taillamp
assembly, from inside the vehicle.
5. Remove the taillamp assembly.
6. Turn the bulb socket counterclockwise to
remove.7. Pull the bulb from the socket.
8. Install a new bulb.
9. Reverse Steps 2 through 7 to reinstall the
taillamp assembly.
Taillamps, Turn Signal,
Sidemarker, Stoplamps and
Back-up Lamps (Coupe)
A. Sidemarker Lamp
B. Stoplamp/Taillamp/Turn Signal Lamp
C. Back-up Lamp
365

To replace one of these bulbs, do the following:
1. Open the trunk. SeeTrunk on page 113
for more information.
2. Remove the convenience net, if the vehicle
has one.
3. Remove the two wing nuts from the trunk trim
to expose the hex nuts.
4. Remove the three hex nuts retaining the
taillamp assembly.5. Pull the assembly off to the side to release it
from the rear of the vehicle.
6. Turn the bulb socket counterclockwise to
remove.
7. Pull the bulb from the bulb socket.
8. Install a new bulb.
9. Reverse Steps 3 through 5 to reinstall the
taillamp assembly.
366

Taillamps, Turn Signal, Sidemarker,
Stoplamps and Back-up Lamps
(Retractable Hardtop)
A. Sidemarker Lamp
B. Stoplamp/Taillamp/Turn Signal Lamp
C. Back-up LampTo replace one of these bulbs, do the following:
1. Open the trunk. SeeTrunk on page 113
for more information.
2. Locate the three rubber covers in the trunk trim,
near the taillamp assembly and remove them.
3. Remove the two nuts and one bolt retaining
the taillamp assembly.
4. Pull off the assembly to the side to release it
from the vehicle.
5. Turn the bulb socket counterclockwise to
remove.
6. Pull the bulb from the bulb socket.
7. Install a new bulb.
8. Reverse Steps 1 through 5 to reinstall the
taillamp assembly.
367

Removing the Spare Tire and Tools
The equipment you will need is located in the
trunk.
1. If you have a retractable hardtop model, make
sure the hardtop is in the up position.
2. Open the trunk. SeeTrunk on page 113for
more information.
3. If you have a sedan or coupe model, lift the
handle on the spare tire cover. The handle
can hook on the front edge of the trunk’s
weatherstrip to hold the cover out of the way.
If you have a retractable hardtop model,
unlatch the trunk cargo cover so that it is in
the open position. Then remove the cover from
the spare tire.4. Turn the wing nut counterclockwise and
remove it. Then remove the compact
spare tire. SeeCompact Spare Tire on
page 403for more information.
5. Remove the wing nut holding the jack
in place.
6. Remove the extension bolt that is clipped to
the jack. You will need this later to store the
at tire.
7. Remove the jack and wheel wrench from the
trunk.
392

{CAUTION:
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the wheel
to come loose and even come off. This
could lead to an accident. Be sure to use
the correct wheel nuts. If you have to
replace them, be sure to get new GM
original equipment wheel nuts. Stop
somewhere as soon as you can and have
the nuts tightened with a torque wrench
to the proper torque specication. See
Capacities and Specifications on page 424
for wheel nut torque specication.
Notice:Improperly tightened wheel nuts can
lead to brake pulsation and rotor damage. To
avoid expensive brake repairs, evenly tighten
the wheel nuts in the proper sequence and to
the proper torque specication. SeeCapacities
and Specifications on page 424for the wheel
nut torque specication.13. Tighten the wheel
nuts rmly in a
crisscross sequence,
as shown, with
the wheel wrench.
Notice:Wheel covers will not t on your
compact spare. If you try to put a wheel cover
on the compact spare, you could damage
the cover or the spare.
Do not try to put a wheel cover on your compact
spare tire. It will not t. Store the wheel cover
in the trunk until you have the at repaired
or replaced.
399