2007 PONTIAC G6 check engine

Checking Things Under
the Hood
{CAUTION:
An electric fan under the hood can start up
and injure you even when the engine is not
running. Keep hands, clothing, and tools
away from any underhood electric fan.
{CAUTION:
Things that burn can get on hot engine
parts and start a re. These include
liquids like fuel, oil, coolant, brake uid,
windshield washer and other uids, and
plastic or rubber. You or others could be
burned. Be careful not to drop or spill
things that will burn onto a hot engine.
316

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 325.
C. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
D. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.
E. Pressure Cap. SeePressure Cap on page 342.F. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
G. Battery. SeeBattery on page 355.
H. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
I. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
319

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 349.
C. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 325.
D. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
E. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.F. Pressure Cap. SeePressure Cap on page 342.
G. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
H. Battery. SeeBattery on page 355.
I. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
J. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
321

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 349.
C. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 325.
D. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
E. Electric Engine Cooling Fans. SeeCooling
System on page 345.
F. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.
G. Pressure Cap. SeePressure Cap on page 342.H. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
I. Automatic Transaxle Fluid Dipstick (Out of
View). See “Checking the Fluid Level” under
Automatic Transaxle Fluid (2.4L L4 and 3.5L V6
Engines) on page 332orAutomatic Transaxle
Fluid (3.6L Engine) on page 332orAutomatic
Transaxle Fluid (3.9L V6 Engine) on page 335.
J. Battery. SeeBattery on page 355.
K. Underhood Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
L. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
323

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Engine Coolant Bleed Valve.
C. Power Steering Fluid. SeePower Steering
Fluid on page 349.
D. Automatic Transaxle Fluid Dipstick (Out of
View). See “Checking the Fluid Level” under
Automatic Transaxle Fluid (2.4L L4 and 3.5L V6
Engines) on page 332orAutomatic Transaxle
Fluid (3.6L Engine) on page 332orAutomatic
Transaxle Fluid (3.9L V6 Engine) on page 335.
E. Engine Oil Fill Cap. See “When to Add
Engine Oil” underEngine Oil on page 325.
F. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
G. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.
H. Pressure Cap. SeePressure Cap on page 342.
I. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
J. Battery. SeeBattery on page 355.K. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
L. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
SeeEngine Compartment Overview on page 318
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you
do not do this, the oil dipstick might not
show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
325

If you are in an area of extreme cold, where
the temperature falls below−20°F (−29°C), it is
recommended that you use either an SAE 5W-30
synthetic oil or an SAE 0W-30 oil. Both will
provide easier cold starting and better protection
for the engine at extremely low temperatures.
Engine Oil Additives
Do not add anything to the oil. The recommended
oils with the starburst symbol that meet GM
Standard GM6094M are all you will need for
good performance and engine protection.
Engine Oil Life System
When to Change Engine Oil
Your vehicle has a computer system that lets you
know when to change the engine oil and lter.
This is based on engine revolutions and engine
temperature, and not on mileage. Based on driving
conditions, the mileage at which an oil change will
be indicated can vary considerably. For the oil life
system to work properly, you must reset the system
every time the oil is changed.When the system has calculated that oil life has
been diminished, it will indicate that an oil change is
necessary. A CHANGE OIL SOON message will
come on. SeeDIC Warnings and Messages on
page 212. Change your oil as soon as possible
within the next 600 miles (1 000 km). It is possible
that, if you are driving under the best conditions, the
oil life system may not indicate that an oil change is
necessary for over a year. However, your engine oil
and lter must be changed at least once a year and
at this time the system must be reset. Your dealer
has GM-trained service people who will perform this
work using genuine GM parts and reset the system.
It is also important to check your oil regularly and
keep it at the proper level.
If the system is ever reset accidentally, you must
change your oil at 3,000 miles (5 000 km) since
your last oil change. Remember to reset the oil life
system whenever the oil is changed.
328

Automatic Transaxle Fluid
(2.4L L4 and 3.5L V6 Engines)
It is not necessary to check the transaxle uid
level. A transaxle uid leak is the only reason for
uid loss. If a leak occurs, take your vehicle to
the dealership service department and have
it repaired as soon as possible.
Change the uid and lter at the intervals listed in
Additional Required Services on page 434, and be
sure to use the transaxle uid listed in
Recommended Fluids and Lubricants on page 442.
Notice:Use of the incorrect automatic
transaxle uid may damage your vehicle, and
the damages may not be covered by your
warranty. Always use the automatic transaxle
uid listed inRecommended Fluids and
Lubricants on page 442.
Automatic Transaxle Fluid
(3.6L Engine)
When to Check and Change Automatic
Transaxle Fluid
A good time to check the automatic transaxle uid
level is when the engine oil is changed.
Change the uid at the intervals listed inAdditional
Required Services on page 434, and be sure to
use the transaxle uid listed inRecommended
Fluids and Lubricants on page 442.
How to Check Automatic Transaxle
Fluid
Because this operation can be a little difficult, you
may choose to have this done at the dealership
service department.
If you do it yourself, be sure to follow all the
instructions here, or you could get a false reading
on the dipstick.
332

Notice:Too much or too little uid can damage
the transaxle. Too much can mean that some of
the uid could come out and fall on hot engine
or exhaust system parts, starting a re. Too
little uid could cause the transaxle to overheat.
Be sure to get an accurate reading if you check
the transaxle uid.
Wait at least 30 minutes before checking the
transaxle uid level if you have been driving:
When outside temperatures are above
90°F (32°C).
At high speed for quite a while.
In heavy traffic — especially in hot weather.
While pulling a trailer.
To get the right reading, the uid should be at
normal operating temperature, which is 180°F to
200°F (82°C to 93°C).
Get the vehicle warmed up by driving about
15 miles (24 km) when outside temperatures are
above 50°F (10°C). If it is colder than 50°F (10°C),
you may have to drive longer.
Checking the Fluid Level
Prepare the vehicle as follows:
1. Park the vehicle on a level place. Keep the
engine running.
2. With the parking brake applied, place the shift
lever in PARK (P).
3. With your foot on the brake pedal, move the
shift lever through each gear, pausing for
about three seconds in each one. Then,
position the shift lever in PARK (P).
4. Let the engine run at idle for three to
ve minutes.
Then, without shutting off the engine, follow
these steps:
The transaxle uid
dipstick handle has this
symbol on it, and is
located near the front of
the engine compartment.
333