2007 NISSAN TIIDA sensor

SELF-DIAGNOSIS CANNOT BE PERFORMED
HAC-311
< SYMPTOM DIAGNOSIS >[AUTO AIR CONDITIONER (W/NAVI)]
C
D
E
F
G
H
J
K
L
MA
B
HAC
N
O
P
SELF-DIAGNOSIS CANNOT BE PERFORMED
Self-DiagnosisINFOID:0000000001679728
SYMPTOM: Self-diagnosis cannot be performed.
INSPECTION FLOW
1.CONFIRM SYMPTOM BY PERFORMING OPERATIONAL CHECK - AUTO MODE
1. Press the AUTO switch.
2. Display should indicate AUTO. Discharge air and blower speed will depend on ambient, in-vehicle and set
temperatures.
Can a symptom be duplicated?
YES >> GO TO 2.
NO >> Perform a complete operational check. Refer to XX-XX, "*****"
.
2.CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 3.
3.CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and ground circuit. Refer to XX-XX, "*****"
.
Is the inspection result normal?
YES >> Cause cannot be confirmed by self-diagnosis.
NO >> GO TO 4.
4.CHECK AMBIENT SENSOR CIRCUIT
Check ambient sensor circuit. Refer to XX-XX, "*****"
.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace as necessary.
5.CHECK IN-VEHICLE SENSOR CIRCUIT
Check in-vehicle sensor circuit. Refer to XX-XX, "*****"
.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace as necessary.
6.CHECK INTAKE SENSOR CIRCUIT
Check intake sensor circuit. Refer to XX-XX, "*****"
.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace as necessary.
7.CHECK AIR MIX DOOR MOTOR PBR CIRCUIT
Check air mix door motor PBR circuit. Refer to XX-XX, "*****"
.
Is the inspection result normal?
OK >> Perform a complete operational check and check for other symptoms. Refer to XX-XX, "*****".
NG >> Repair or replace as necessary.

INT-28
< ON-VEHICLE REPAIR >
FLOOR TRIM
6. Disconnect floor harness connector.
7. Remove diagnosis sensor unit. Refer to SR-15, "
Removal and
Installation".
8. Remove key interlock cable. Refer to TM-206, "
Removal and
Installation".
9. Remove floor carpet hook.
10. Cut floor trim using a blade knife first between openings (1),
then at front edge (2) as shown.
NOTE:
LHD shown, RHD similar
11. Release floor trim metal clips after cutting, then pull out floor trim through door opening.
12. Remove floor spacer RH/LH.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When replacing the floor trim with a new one, prepare for installation by cutting it like the old one.
Make sure there is a quality fit between floor trim and instrument lower cover by tucking the cut edge
completely.
PIIB6046E
PIIB2580J
PIIB6047E

LAN
HOW TO USE THIS SECTION
LAN-27
< HOW TO USE THIS MANUAL >[CAN]
C
D
E
F
G
H
I
J
K
L B A
O
P N
HOW TO USE THIS MANUAL
HOW TO USE THIS SECTION
CautionINFOID:0000000001162766
 This section describes information peculiar to a vehicle and inspection procedures.
 For trouble diagnosis procedure, refer to LAN-22, "
Trouble Diagnosis Procedure".
Abbreviation ListINFOID:0000000001162767
Unit name abbreviations in CONSULT-III CAN diagnosis and in this section are as per the following list.
Abbreviation Unit name
ABS ABS actuator and electric unit (control unit)
AV NAVI control unit
BCM BCM
DLC Data link connector
ECM ECM
EPS EPS control unit
I-KEY Intelligent Key unit
IPDM-E IPDM E/R
M&A Combination meter
STRG Steering angle sensor
TCM TCM

LAN-34
< FUNCTION DIAGNOSIS >[CAN]
CAN COMMUNICATION SYSTEM
Buzzer output signalTR
TR
Day time running light request signal T R
Door lock/unlock signal T R
Door switch signal T R R
Front fog light request signal T R R
Front wiper request signal T R
High beam request signal T R R
Ignition switch signal T R
Low beam request signal T R
Position light request signal T R R
Rear fog lamp status signal T R
Rear window defogger switch signal T R
Sleep wake up signalTRR R
RT
RT
RT
Trunk open/close status signal T R
Turn indicator signal T R
EPS operation signal
*3RT
EPS warning lamp signal T R
Door lock/unlock trunk open request signal R T
Hazard request signal R T
Key warning lamp signal T R
LOCK warning lamp signal T R
Distance to empty signal T R
Fuel level sensor signal R T
Overdrive control signal T R
P/N renge signal T R
Stop lamp switch signalTR
RT
Vehicle speed signalRRRRT R
RRR TR
Steering angle sensor signal
*1TR
ABS warning lamp signal R T
Brake warning lamp signal R T
ESP OFF indicator lamp signal
*1RT
A/T check indicator signal R T
A/T self-diagnosis signal R T
OD OFF indicator lamp signal R T
Output shaft revolution signal R T
Shift position indicator signal R
R
*1T Signal name/Connecting unit
ECM
BCM
EPS
I-KEY
M&A
STRG
AV
ABS
TCM
IPDM-E

LAN-36
< COMPONENT DIAGNOSIS >[CAN]
CAN COMMUNICATION SYSTEM
COMPONENT DIAGNOSIS
CAN COMMUNICATION SYSTEM
Component Parts LocationINFOID:0000000001162774
LHD MODELS
RHD MODELS
1. BCM M18 2. ABS actuator and electric unit (con-
trol unit) E333. IPDM E/R E46
4. ECM E16 5. EPS control unit M53 6. TCM E31
7. Combination meter M24 8. Data link connector M22 9. Steering angle sensor M80
10. NAVI control unit B68 11. Intelligent Key unit M52
AWMIA0004ZZ

LAN
CAN COMMUNICATION SYSTEM
LAN-37
< COMPONENT DIAGNOSIS >[CAN]
C
D
E
F
G
H
I
J
K
L B A
O
P N
1. Data link connector M22 2. Combination meter M24 3. EPS control unit M53
4. Intelligent Key unit M52 5. IPDM E/R E46 6. ECM E16
7. ABS actuator and electric unit (con-
trol unit) E338. TCM E31 9. BCM M18
10. NAVI control unit B68 11. Steering angle sensor M80
AWMIA0005ZZ

LAN-42
< COMPONENT DIAGNOSIS >[CAN]
MALFUNCTION AREA CHART
MALFUNCTION AREA CHART
Main LineINFOID:0000000001162777
Branch LineINFOID:0000000001162778
Short CircuitINFOID:0000000001162779
Malfunction Area Reference
Main line between data link connector and ABS actuator and
electric unit (control unit)LAN-43, "
Diagnosis Procedure"
Main line between data link connector and NAVI control unitLAN-44, "Diagnosis Procedure"
Main line between NAVI control unit and ABS actuator and elec-
tric unit (control unit)LAN-45, "Diagnosis Procedure"
Malfunction Area Reference
ECM branch line circuit LAN-47, "
Diagnosis Procedure"
BCM branch line circuit LAN-48, "Diagnosis Procedure"
Data link connector branch line circuit LAN-49, "Diagnosis Procedure"
EPS control unit branch line circuit LAN-50, "Diagnosis Procedure"
Intelligent Key unit branch line circuit LAN-51, "Diagnosis Procedure"
Combination meter branch line circuit LAN-52, "Diagnosis Procedure"
Steering angle sensor branch line circuit LAN-53, "Diagnosis Procedure"
NAVI control unit branch line circuit LAN-54, "Diagnosis Procedure"
ABS actuator and electric unit (control unit) branch line circuit LAN-55, "Diagnosis Procedure"
TCM branch line circuitLAN-56, "Diagnosis Procedure"
IPDM E/R branch line circuit LAN-57, "Diagnosis Procedure"
Malfunction Area Reference
CAN communication circuitLAN-58, "
Diagnosis Procedure"

LAN
STRG BRANCH LINE CIRCUIT
LAN-53
< COMPONENT DIAGNOSIS >[CAN]
C
D
E
F
G
H
I
J
K
L B A
O
P N
STRG BRANCH LINE CIRCUIT
Diagnosis ProcedureINFOID:0000000001162797
INSPECTION PROCEDURE
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the steering angle sensor for damage, bend and loose connection
(unit side and connector side).
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the terminal and connector.
2.CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of steering angle sensor.
2. Check the resistance between the steering angle sensor harness connector terminals.
Is the measurement value within the specification?
YES >> GO TO 3.
NO >> Repair the steering angle sensor branch line.
3.CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the steering angle sensor. Refer to BRC-142, "
Diagnosis
Procedure".
Is the inspection result normal?
YES (Present error)>>Replace the steering angle sensor. Refer to BRC-186, "Removal and Installation".
YES (Past error)>>Error was detected in the steering angle sensor branch line.
NO >> Repair the power supply and the ground circuit.
Steering angle sensor harness connector
Resistance (Ω)
Connector No. Terminal No.
M80 4 8 Approx. 54 – 66