2007 NISSAN MURANO Screen

the vehicle, doors can be locked with an-
other Intelligent Key.
Unlocking doors and fuel-filler door1. Push the door handle request switch or lift
gate request switch once.
Driver’s side:

The driver door and fuel-filler door unlock.
Front passenger side or lift gate:

Only corresponding door unlocks.
2. The hazard indicator flashes once and out-
side buzzer sounds once if all doors are
completely closed with the ignition key in any
position except the ON position.
3. Push the door handle request switch or lift
gate request switch again within 5 seconds.

All doors and the fuel-filler door unlock.

The hazard indicator flashes once and out-
side buzzer sounds once if all doors are
completely closed.
All doors will be locked automatically after push-
ing the door handle request switch or lift gate
request switch unless one of the following op-
erations is performed within 1 minute.

any door is opened
the ignition switch is pushed

the mechanical key or the valet key is inserted
into the ignition switch
Re-lock time can be adjusted or cancelled with
the vehicle electronic systems on the monitor
(see “4. Display screen, heater, air conditioner
and audio systems”).
The room light will come on for 30 seconds
when the door is unlocked using the request
switch.
The room light can be turned off without waiting
for 30 seconds by turning the ignition switch to
the ON position or by locking the doors.
OPERATING THE ENGINE
Ignition switch positionsPush in the ignition switch in the range (
A
to
B) when you turn it.
LOCK (Normal parking position)
A:
The ignition switch can only be locked in the
A
position.
The ignition switch will be unlocked when it is
pushed in, and turned to the ACC position
C
while carrying the Intelligent Key.
SSD0417
Pre-driving checks and adjustments
3-13


06.7.5/Z50-D/V5.0


Display screen, heater, air conditioner and
audio systems”.
For buzzer operation, refer to the following chart.
In hazard indicator and horn (buzzer) mode,
when the LOCK button
Ais pushed, the hazard
indicator flashes twice and the horn chirps once
(refer to the “operation guide” chart for the
Intelligent Key request switch mode). When the
UNLOCK button
B
is pushed, the hazard indi-
cator flashes once.
If hazard indicator and horn mode is not neces-
sary, you can switch to hazard indicator only
mode by following the switching procedure.In hazard indicator only mode, when the LOCK
button
Ais pushed, the hazard indicator flashes
twice. When the UNLOCK button
Bis pushed,
neither the hazard indicator nor the horn oper-
ates.
(Switching procedure)
Push the LOCK
Aand UNLOCK
Bbuttons on
the Intelligent key simultaneously for more than 2
seconds to switch from one mode to the other.
When pushing the buttons to set hazard indica-
tor mode, the hazard indicator flashes 3 times.
When pushing the buttons to set hazard indica-
tor and horn mode, the hazard indicator flashesonce and the horn chirps once.
Locking doors and fuel-filler door:
1. Remove the mechanical key or the valet key if
any key is in the ignition switch.*1
2. Close all the doors.*2
3. Push the LOCK button
A
on the Intelligent
Key.
4. All the doors (including lift gate) and fuel-filler
door will lock.
All of the doors will lock when the LOCK
button
A
on the Intelligent Key is pushed
SPA1950A
Pre-driving checks and adjustments
3-21


06.7.5/Z50-D/V5.0


The automatic drive positioner system has two
features:

Entry/exit function

Memory storageENTRY/EXIT FUNCTIONThis system is designed so that the driver’s seat
and outside mirror will automatically move when
the selector lever is in the P (Park) position. This
allows the driver to get into and out of the
driver’s seat more easily.
The driver’s seat will slide backward:
The driver’s seat will slide backward when the
driver’s door is opened with the ignition switch
(knob) in the LOCK position.
The driver’s seat will return to the previous
position:

When the key is inserted into the ignition
switch after closing the driver’s door, or when
the driver’s door is closed after inserting the
key into the ignition switch.

When the ignition switch is pushed with the
driver’s door closed. (Intelligent Key
equipped model)

When the key or ignition switch is turned to
the ON position.
The driver’s seat will not return to the previ-
ous positions if the seat adjusting switch is
operated when the seat is at the exit position.
The entry/exit feature can be canceled. See “4.
Display screen, heater, air conditioner and audio
systems” section of this manual.
The entry/exit function can be activated or can-
celled by pressing and holding the SET switch
for more than 10 seconds while the ignition key
is in the LOCK position. The indicator light will
blink once when the function is cancelled, and
the indicator light will blink twice when the
function is activated. If the battery cable is
disconnected, or if the fuse opens, the entry/exit
function will be cancelled. In such a case, after
connecting the battery or replacing with a new
fuse, open and close the driver’s door more than
two times with the ignition key or ignition switch
in the LOCK position to activate the entry/exit
function.
MEMORY STORAGETwo positions for the driver’s seat, pedals (Brake
and Accelerator) and outside mirrors can be
stored in the automatic drive positioner memory.
Follow these procedures to use the memory
system.
1. Set the selector lever to the P (Park) position.
2. Adjust the driver’s seat, pedals (Brake and
Accelerator) and outside mirrors to the de-
sired positions by manually operating each
adjusting switch. For additional information,
see “Seats” in the “1. Safety — seats, seat
belts and supplemental restraint system”
SPA2185
AUTOMATIC DRIVE POSITIONER
(if so equipped)
Pre-driving checks and adjustments
3-33


06.7.5/Z50-D/V5.0


4 Display screen, heater, air conditioner and
audio systemsSafety note .............................................................................. 4-2
Control panel buttons — without navigation system .... 4-2
How to use joystick and “ENTER” button ................. 4-3
How to use “BACK” button .......................................... 4-3
How to use “TRIP” button ............................................. 4-3
How to use “FUEL ECON” button .............................. 4-3
Clock ................................................................................... 4-4
How to use “E/M” button .............................................. 4-4
How to use “MAINT” (Maintenance) button ............. 4-4
Maintenance notice ......................................................... 4-5
How to use “SETTING” button .................................... 4-6
“DAY/NIGHT” button.................................................... 4-10
Control panel buttons — with navigation system ....... 4-11
How to use joystick and “ENTER” button .............. 4-11
How to use “BACK” button........................................ 4-11
Setting up the start-up screen................................... 4-12
How to use the “TRIP” button ................................... 4-12
Maintenance notice ....................................................... 4-14
How to use the “SETTING” button .......................... 4-15
“DAY/NIGHT” button.................................................... 4-19
RearView Monitor (if so equipped) ................................. 4-19
How to read the displayed lines................................ 4-20RearView Monitor setting ............................................ 4-20
Operating tips................................................................. 4-20
Ventilators .............................................................................. 4-21
Heater and air conditioner (Automatic) ......................... 4-23
Automatic operation ...................................................... 4-24
Manual operation ........................................................... 4-25
Operating tips................................................................. 4-25
In-cabin microfilter ......................................................... 4-26
Servicing air conditioner .................................................... 4-26
Audio system ........................................................................ 4-27
FM radio reception ........................................................ 4-27
AM radio reception ....................................................... 4-28
Satellite radio reception ............................................... 4-28
Audio operation precautions....................................... 4-28
FM-AM-SAT radio with CD player .......................... 4-34
FM-AM-SAT radio with cassette player and CD
changer ............................................................................ 4-38
CD care and cleaning .................................................. 4-43
Steering switch for audio control (if so
equipped)......................................................................... 4-43
Antenna ............................................................................ 4-44
Car phone or CB radio .................................................... 4-45


06.7.5/Z50-D/V5.0


WARNING

Do not disassemble or modify this
system. If you do, it may result in
accidents, fire, or electrical shock.

Do not use this system if you notice
any abnormality, such as a frozen
screen or lack of sound. Continued
use of the system may result in acci-
dent, fire or electric shock.

In case you notice any foreign object
in the system hardware, spill liquid
on it, or notice smoke or smell com-
ing from it, stop using the system
immediately and contact a NISSAN
dealer. Ignoring such conditions may
lead to accidents, fire, or electrical
shock.
1. “TRIP” button
2. “FUEL ECON” button
3. Clock adjust button
4. “TRIP RESET” button5. “E/M” button
6. “DAY/NIGHT” button
7. “BACK” button
8. JOYSTICK and “ENTER” button
SAA1352
SAFETY NOTE
CONTROL PANEL BUTTONS —
WITHOUT NAVIGATION SYSTEM4-2
Display screen, heater, air conditioner and audio systems


06.7.5/Z50-D/V5.0


9. “SETTING” button
10. “MAINT” maintenance button
Make sure the engine is running before using
this system.
If you use the system with the engine not
running (ignition ONor ACC) for a long
time, it will use up all the battery power,
and the engine will not start.HOW TO USE JOYSTICK AND
“ENTER” BUTTONChoose an item on the display using the joystick.
Push the “ENTER” button only when the use of
it is instructed on the display.HOW TO USE “BACK” BUTTONFinish setup:
If you push the “BACK” button after the setup is
completed, the display will return to the previous
screen.
HOW TO USE “TRIP” BUTTONWhen the “TRIP” button is pushed, the following
modes will display on the screen.
TRIP 1 (TIME, DIST, AVG)→TRIP 2 (TIME,
DIST, AVG)→OFF
Elapsed Time, Driving Distance and Average
Speed will be displayed.
To reset, select the “Reset” key using the joy-
stick and push the “ENTER” button, or push the
“TRIP RESET” or “TRIP” button for more than
approximately 1.5 seconds.
HOW TO USE “FUEL ECON”
BUTTONAverage Fuel Economy and Distance to Empty
will be displayed for reference when the “FUEL
ECON” button is pushed.
To reset, select the “Reset” key using the joy-
stick and push the “ENTER” button, or push the
“TRIP RESET” or “TRIP” button for more than
approximately 1.5 seconds.
SAA1317
SAA1318
Display screen, heater, air conditioner and audio systems
4-3


06.7.5/Z50-D/V5.0


CLOCKThe digital clock displays time when the ignition
switch is in ACC or ON.
If the battery cable is disconnected, the
clock will not indicate the correct time.
Readjust the time.Adjusting the timeTo adjust the time, push the “H” or “M” button for
more than approximately 1.5 seconds. The time
indicator will flash.
Push theHbutton to adjust the hour.
Push theMbutton to adjust the minute.To finish the adjusting, push the “BACK” button
or the screen will return to normal after 10
seconds.
The clock can be adjusted on the setting display.
See the “HOW TO USE “SETTING” BUTTON”
later in this section.
HOW TO USE “E/M” BUTTONYou can change the unit as follows using the
“E/M” (English/Metric) button.
Unit: US — Mile, °F, MPG
Metric — km, °C, L/100 km
HOW TO USE “MAINT”
(Maintenance) BUTTONMaintenance and tire pressure information (if so
equipped) will be displayed when the “MAINT”
button is pushed.
To display the setting of the maintenance inter-
val, select the “Engine Oil” or “Tire Rotation” key
using the joystick and push the “ENTER” button.
To set the maintenance interval, select the
“Maintenance Schedule” key by using the joy-
stick and move the joystick to the right or left.
To reset the maintenance interval, select the
SAA1353
SAA1319
4-4
Display screen, heater, air conditioner and audio systems


06.7.5/Z50-D/V5.0


“Reset” key using the joystick and push the
“ENTER” button.
To display the MAINTENANCE NOTICE, auto-
matically when setting trip distance is reached,
select the “Display Maintenance Notification”
key and push the “ENTER” button.
MAINTENANCE NOTICEThe “MAINTENANCE NOTICE” screen (“EN-
GINE OIL” or “TIRE ROTATION”) will be auto-
matically displayed as shown when both of the
following conditions are met:

the vehicle is driven the set distance and the
ignition switch is turned OFF.

the ignition key is turned ON the next time the
vehicle will be driven.
To return to the previous display after the
“MAINTENANCE NOTICE” screen is displayed,
push the “BACK” button.The “MAINTENANCE NOTICE” screen displays
each time the key is turned ON until one of the
following conditions are met:

“RESET” is selected.

“Display Maintenance Notification” is set
OFF.

the maintenance interval is set again.
SAA1320
SAA1354
Display screen, heater, air conditioner and audio systems
4-5


06.7.5/Z50-D/V5.0