2007 NISSAN LATIO engine

WATER PUMP
CO-17
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: June 20062007 Versa
WATER P UM PPFP:21020
ComponentsEBS00U84
Removal and InstallationEBS00U85
REMOVAL
1. Drain engine coolant. Refer to CO-8, "DRAINING ENGINE COOLANT" .
CAUTION:
Perform this step when the engine is cold.
2. Remove drive belt auto-tensioner. Refer to EM-37, "
TIMING CHAIN" .
3. Remove water pump.
CAUTION:

Handle water pump vane so that it does not contact any other parts.

Water pump cannot be disassembled and should be replaced as a unit.
INSPECTION AFTER REMOVAL

Visually check that there is no significant dirt or rusting on water
pump body and vane (A).

Make sure that there is no looseness in vane shaft, and that it
turns smoothly when rotated by hand.

Replace water pump, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant. Refer to CO-8, "Inspection" .

Start and warm up the engine. Visually check if there is no leaks of engine coolant.
1. Gasket 2. Water pump
PBIC3921E
PBIC3313J

CO-18Revision: June 2006
THERMOSTAT
2007 Versa
THERMOSTATPFP:21200
ComponentsEBS00U6H
Removal and InstallationEBS00U6I
REMOVAL
1. Drain engine coolant. Refer to CO-8, "DRAINING ENGINE COOLANT" .
2. Remove water inlet.
3. Remove thermostat.
4. Remove water pump. Refer to CO-17, "
WAT ER PUM P" .
5. Remove thermostat housing.
INSPECTION AFTER REMOVAL

Place a thread (A) so that it is caught in the valves of thermostat
(1). Immerse fully in a container (B) filled with water. Heat while
stirring.

The valve opening temperature is the temperature at which the
valve opens and falls from the thread.

Continue heating. Check the full open valve lift amount.

After checking the maximum valve lift amount, lower the water
temperature and check the valve closing temperature.
1. Thermostat housing 2. Water hose (models with oil cooler) 3. Radiator hose (lower)
4. Water inlet 5. Thermostat 6. Rubber ring
7. Gasket A. To oil cooler B. To radiator
Engine front
PBIC4485E
PBIC3314J

THERMOSTAT
CO-19
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: June 20062007 Versa

If out of the specification, replace thermostat.
INSTALLATION
Installation is in the reverse order of removal.
Thermostat
CAUTION:
Replace the rubber ring with a new one.

Install thermostat while making rubber ring (1) groove fit to ther-
mostat flange (A) around the whole circumference.

Install thermostat (1) into the thermostat housing (2) with jiggle
valve (A) facing upwards.
Thermostat Housing
CAUTION:
Replace the rubber ring with a new one.

Securely insert the rubber ring into the mating groove of thermostat housing and install it.

Install the thermostat housing to the cylinder block without displacing the gasket from the gasket position.
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant. Refer to CO-8, "CHECKING COOLING SYSTEM FOR LEAKS" .

Start and warm up the engine. Visually check for engine coolant leaks.
ItemsThermostat
Valve opening temperature 80.5 - 83.5°C (177 - 182°F)
Maximum valve lift 8 mm/ 95°C (0.315 in/ 203°F)
Valve closing temperature 77°C (171°F)
PBIC3315J
PBIC3548J

CO-20Revision: June 2006
WATER OUTLET AND WATER CONTROL VALVE
2007 Versa
WATER OUTLET AND WATER CONTROL VALVEPFP:11060
ComponentsEBS00U86
Removal and InstallationEBS00U87
REMOVAL
1. Drain engine coolant. Refer to CO-8, "DRAINING ENGINE COOLANT" .
CAUTION:
Perform this step when the engine is cold.
2. Remove air duct. Refer to EM-16, "
Components" .
3. Remove radiator hose (upper). Refer to CO-11, "
Components" .
4. Remove heater hoses and water hoses.
5. Remove water outlet.
6. Remove water control valve.
7. Remove engine coolant temperature sensor, if necessary.
CAUTION:

Handle carefully to avoid any shock to engine coolant temperature sensor.

Replace the gasket with a new one.
1. Engine coolant temperature sensor 2. Rubber ring 3. Water control valve
4. Gasket 5. Water hose 6. Gasket
7. Water hose 8. Water outlet 9. Heater hose
10. Heater hose 11. Radiator hose (upper) Front
A. To heater B. To electric throttle control actuator C. To radiator
PBIC4699E

CO-22Revision: June 2006
WATER OUTLET AND WATER CONTROL VALVE
2007 Versa
Water H oses
Install water hoses (3),(5) as shown.

Electric throttle control actuator (1)

Clamp (2)

Water outlet (4)

Paint mark (A)

Clamp shall not interfere with the bulged area (B)
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant. Refer to CO-8, "Inspection" .

Start and warm up the engine. Visually check if there is no leaks of engine coolant.
PBIC4703E

SERVICE DATA AND SPECIFICATIONS (SDS)
CO-23
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: June 20062007 Versa
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitEBS00T7Q
CAPACITY
Unit: (US qt, lmp qt)
THERMOSTAT
WATER CONTROL VALVE
RADIATOR
Unit: kPa (bar, kg/cm2 , psi)
Engine coolant capacity (with reservoir tank at “MAX” level) Approx. 6.8 (7 1/4, 6.0)
Valve opening temperature 80.5 - 83.5°C (177 - 182°F)
Maximum valve lift 8 mm/ 95°C (0.315 in/ 203°F)
Valve closing temperature 77°C (171°F)
Valve opening temperature 93.5 - 96.5°C (200 - 206°F)
Maximum valve lift 8 mm/ 108°C (0.315 in/ 226°F)
Valve closing temperature 90°C (194°F)
Cap relief pressureStandard 78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11- 14)
Limit 59 (0.59, 0.6, 9)
Leakage test pressure 157 (1.57, 1.6, 23)

CVT-1
CVT
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION CVT
A
B
CVT
Revision: June 20062007 Versa INDEX FOR DTC ........................................................ 6
Alphabetical Index .................................................... 6
DTC No. Index ......................................................... 7
PRECAUTIONS .......................................................... 8
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 8
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 8
OPERATION PROCEDURE ................................. 8
Precautions for On Board Diagnostic (OBD) System
of CVT and Engine ................................................... 9
Service After Replacing TCM and Transaxle
Assembly .................................................................. 9
SERVICE AFTER REPLACING TCM AND
TRANSAXLE ASSEMBLY ..................................... 9
PATTERN A .......................................................... 9
PATTERN B .......................................................... 9
PATTERN C .........................................................11
Removal and Installation Procedure for CVT Unit
Connector ................................................................11
REMOVAL ............................................................11
INSTALLATION ................................................... 12
Precautions ............................................................ 13
Service Notice or Precautions ................................ 13
CVT FLUID COOLER SERVICE ......................... 13
OBD-II SELF-DIAGNOSIS .................................. 14
PREPARATION ......................................................... 15
Special Service Tools ............................................. 15
Commercial Service Tools ...................................... 15
CVT FLUID ............................................................... 16
Checking CVT Fluid ............................................... 16
FLUID LEVEL CHECK ........................................ 16
FLUID CONDITION CHECK ............................... 17
Changing CVT Fluid ............................................... 17
CVT Fluid Cooler Cleaning .................................... 18
CVT FLUID COOLER CLEANING PROCEDURE
... 18
CVT FLUID COOLER DIAGNOSIS PROCE-DURE .................................................................. 19
CVT FLUID COOLER INSPECTION PROCE-
DURE .................................................................. 20
CVT FLUID COOLER FINAL INSPECTION ........ 20
CVT SYSTEM ............................................................ 21
Cross-sectional View - RE0F08A ........................... 21
Control System ....................................................... 22
Hydraulic Control System ....................................... 23
TCM Function ......................................................... 24
CONTROL SYSTEM OUTLINE .......................... 24
CONTROL SYSTEM DIAGRAM ......................... 24
CAN Communication .............................................. 25
SYSTEM DESCRIPTION .................................... 25
Input/Output Signal of TCM .................................... 25
Line Pressure and Secondary Pressure Control .... 26
NORMAL CONTROL .......................................... 26
FEEDBACK CONTROL ...................................... 26
Shift Control ............................................................ 26
“D” POSITION ..................................................... 27
OVERDRIVE-OFF MODE ................................... 27
“L” POSITION ...................................................... 27
DOWNHILL ENGINE BRAKE CONTROL (AUTO
ENGINE BRAKE CONTROL) .............................. 27
ACCELERATION CONTROL .............................. 27
Lock-up and Select Control .................................... 28
TORQUE CONVERTER CLUTCH AND SELECT
CONTROL VALVE CONTROL ............................ 28
Control Valve .......................................................... 29
FUNCTION OF CONTROL VALVE ..................... 29
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 30
Introduction ............................................................. 30
OBD-II Function for CVT System ........................... 30
One or Two Trip Detection Logic of OBD-II ............ 30
ONE TRIP DETECTION LOGIC ......................... 30
TWO TRIP DETECTION LOGIC ......................... 30
OBD-II Diagnostic Trouble Code (DTC) ................. 30
HOW TO READ DTC AND 1ST TRIP DTC ......... 30
HOW TO ERASE DTC ........................................ 31
HOW TO ERASE DTC (WITH CONSULT-II) ....... 32

CVT-2Revision: June 20062007 Versa HOW TO ERASE DTC (WITH GST) ................... 32
Malfunction Indicator Lamp (MIL) ........................... 33
DESCRIPTION .................................................... 33
TROUBLE DIAGNOSIS ............................................ 34
DTC Inspection Priority Chart ................................. 34
Fail-safe .................................................................. 34
FAIL-SAFE FUNCTION ....................................... 34
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 35
INTRODUCTION ................................................. 35
WORK FLOW ...................................................... 36
DIAGNOSTIC WORKSHEET .............................. 37
CVT Electrical Parts Location ................................. 40
Circuit Diagram ....................................................... 42
Inspections before Trouble Diagnosis .................... 43
CVT FLUID CHECK ............................................ 43
STALL TEST ........................................................ 43
LINE PRESSURE TEST ...................................... 45
Road Test ............................................................... 46
DESCRIPTION .................................................... 46
CONSULT-II OPERATION PROCEDURE ........... 47
Check before Engine Is Started .............................. 49
Check at Idle ........................................................... 49
Cruise Test .............................................................. 50
Vehicle Speed When Shifting Gears ...................... 53
TCM Input/Output Signal Reference Values ........... 54
TCM TERMINAL CONNECTOR LAYOUT .......... 54
TCM INSPECTION TABLE .................................. 54
CONSULT-II Function (TRANSMISSION) .............. 57
FUNCTION .......................................................... 57
CONSULT-II REFERENCE VALUE ..................... 57
CONSULT-II SETTING PROCEDURE ................ 59
WORK SUPPORT MODE ................................... 59
SELF-DIAGNOSTIC RESULT MODE ................. 60
DATA MONITOR MODE ...................................... 64
CAN DIAGNOSTIC SUPPORT MONITOR
MODE .................................................................. 66
Diagnostic Procedure without CONSULT-II ............ 67
OBD-II SELF-DIAGNOSTIC PROCEDURE
(WITH GST) ......................................................... 67
DTC U1000 CAN COMMUNICATION LINE .............. 68
Description .............................................................. 68
On Board Diagnosis Logic ...................................... 68
Possible Cause ....................................................... 68
DTC Confirmation Procedure ................................. 68
WITH CONSULT-II .............................................. 68
WITH GST ........................................................... 68
Wiring Diagram — CVT — CAN ............................. 69
Diagnostic Procedure ............................................. 70
DTC U1010 TRANSMISSION CONTROL MODULE
(CAN) ......................................................................... 71
Description .............................................................. 71
On Board Diagnosis Logic ...................................... 71
Possible Cause ....................................................... 71
DTC Confirmation Procedure ................................. 71
WITH CONSULT-II .............................................. 71
WITH GST ........................................................... 71
Diagnostic Procedure ............................................. 71
DTC P0615 START SIGNAL CIRCUIT ..................... 72Description ..............................................................72
CONSULT-II Reference Value .................................72
On Board Diagnosis Logic ......................................72
Possible Cause .......................................................72
DTC Confirmation Procedure ..................................72
WITH CONSULT-II ...............................................72
Wiring Diagram — CVT — STSIG ..........................73
Diagnostic Procedure ..............................................74
DTC P0703 STOP LAMP SWITCH CIRCUIT ............76
Description ..............................................................76
CONSULT-II Reference Value .................................76
On Board Diagnosis Logic ......................................76
Possible Cause .......................................................76
DTC Confirmation Procedure ..................................76
WITH CONSULT-II ...............................................76
Diagnostic Procedure ..............................................77
DTC P0705 PARK/NEUTRAL POSITION SWITCH ...78
Description ..............................................................78
CONSULT-II Reference Value .................................78
On Board Diagnosis Logic ......................................78
Possible Cause .......................................................78
DTC Confirmation Procedure ..................................78
WITH CONSULT-II ...............................................79
WITH GST ...........................................................79
Wiring Diagram — CVT — PNP/SW .......................80
Diagnostic Procedure ..............................................82
Component Inspection ............................................84
PNP SWITCH ......................................................84
DTC P0710 CVT FLUID TEMPERATURE SENSOR
CIRCUIT ....................................................................85
Description ..............................................................85
CONSULT-II Reference Value .................................85
On Board Diagnosis Logic ......................................85
Possible Cause .......................................................85
DTC Confirmation Procedure ..................................85
WITH CONSULT-II ...............................................85
WITH GST ...........................................................85
Wiring Diagram — CVT — FTS ..............................86
Diagnostic Procedure ..............................................87
Component Inspection ............................................89
CVT FLUID TEMPERATURE SENSOR ..............89
DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI
SPEED SENSOR) .....................................................90
Description ..............................................................90
CONSULT-II Reference Value .................................90
On Board Diagnosis Logic ......................................90
Possible Cause .......................................................90
DTC Confirmation Procedure ..................................90
WITH CONSULT-II ...............................................90
WITH GST ...........................................................90
Wiring Diagram — CVT — PRSCVT ......................91
Diagnostic Procedure ..............................................92
DTC P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) .....................................95
Description ..............................................................95
CONSULT-II Reference Value .................................95
On Board Diagnosis Logic ......................................95
Possible Cause .......................................................95
DTC Confirmation Procedure ..................................95