Page 606 of 2896
INTELLIGENT KEY SYSTEM
BL-117
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
Symptom Diagnosis/service procedure Reference page
Door lock/unlock do not operate by all request
switch.1. Check door switch.BL-129
2. Check key switch.BL-124
3. Check ignition knob switch.BL-127
4. Replace Intelligent Key unit.BL-160
Door lock/unlock does not operate by request
switch (driver side).1. Check door request switch (driver side).BL-1322. Check outside key antenna (driver side).BL-139
3. Replace Intelligent Key unit.BL-160
Door lock/unlock does not operate by request
switch (passenger side).1. Check door request switch (passenger side).BL-1322. Check outside key antenna (passenger side).BL-139
3. Replace Intelligent Key unit.BL-160
Door lock/unlock does not operate by back door
request switch.1. Check back door request switch.BL-1342. Check outside key antenna (rear bumper).BL-141
3. Replace Intelligent Key unit.BL-160
Auto lock function does not operate.1.Check “AUTO RELOCK TIMER” setting in “WORK
SUPPORT”.BL-113
2. Replace Intelligent Key unit.BL-160
Key reminder function does not operate.1. Check door switch.BL-129
2. Check inside key antenna.BL-143
3. Check unlock sensor.BL-136
4. Check Intelligent Key battery.BL-159
5. Replace Intelligent Key unit.BL-160
Page 607 of 2896
BL-118
INTELLIGENT KEY SYSTEM
Revision: June 20062007 Versa
REMOTE KEYLESS ENTRY FUNCTION MALFUNCTION
NOTE:
Before performing the diagnosis in the following table, check “Trouble Diagnosis Procedure”. Refer to BL-
109, "Trouble Diagnosis Procedure" .
Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.
If the following “symptoms” are detected, check systems shown in the “Diagnosis/service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)
Ignition switch is not depressed.
All doors are closed.
Symptom Diagnosis/service procedureReference
page
All of the remote keyless entry functions
do not operate.1. Check Intelligent Key unit power supply and ground circuit.BL-123
2. Check key switch (BCM input).BL-126
3. Check Intelligent Key battery.BL-159
4. Remote Keyless Entry function inspection.BL-159
5. Replace Intelligent Key unit.BL-160
Auto lock function does not operate.1. Check “AUTO RELOCK TIMER” setting in “WORK SUPPORT”.BL-1132. Replace Intelligent Key unit.BL-160
Key reminder function does not operate.1. Check door switch.BL-129
2. Check inside key antenna.BL-143
3. Check unlock sensor.BL-136
4. Check Intelligent Key battery.BL-159
5. Replace Intelligent Key unit.BL-160
Panic alarm function does not operate.1. Check “PANIC ALARM DELAY” setting in “WORK SUPPORT”.BL-113
2. Check Intelligent Key battery inspection.BL-159
3. Check horn function.BL-157
4. Check headlamp function.BL-158
5. Check key switch.BL-124
6. Check ignition knob switch.BL-127
7. Replace Intelligent Key unit.BL-160
Page 608 of 2896
INTELLIGENT KEY SYSTEM
BL-119
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
HAZARD AND BUZZER REMINDER FUNCTION MALFUNCTION
NOTE:
Before performing the diagnosis in the following table, check “Trouble Diagnosis Procedure”. Refer to BL-
109, "Trouble Diagnosis Procedure" .
Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.
If the following “symptoms” are detected, check systems shown in the “Diagnosis/service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)
Ignition switch is not depressed.
All doors are closed.
Symptom Diagnosis/service procedure Reference page
Hazard reminder does not operate by request
switch.
(Buzzer reminder operate).1.Check “HAZARD ANSWER BACK” setting in “WORK
SUPPORT”.BL-113
2. Check hazard function with hazard switch.BL-157
3. Replace Intelligent Key unit.BL-160
Buzzer reminder does
not operate by request
switch.
(Hazard reminder oper-
ates).Intelligent Key
warning buzzer
does not operate.1.Check “ANSER BACK WITH I-KEY LOCK” or “ANSER
BACK WITH I-KEY UNLOCK” setting in “WORK SUP-
PORT”.BL-113
2. Check Intelligent Key warning buzzer.BL-138
3. Replace Intelligent Key unit.BL-160
Hazard reminder does not operate by Intelli-
gent Key (door lock/unlock button).
(Buzzer reminder operate properly).1.Check “HAZARD ANSWER BACK” setting in “WORK
SUPPORT”.BL-113
2. Check hazard function with hazard switch.BL-157
3. Replace Intelligent Key.BL-160
Buzzer reminder does
not operate by Intelligent
Key (door lock/unlock
button).
(Hazard reminder oper-
ates).Intelligent Key
warning buzzer
does not operate.1.Check “HORN WITH KEYLESS LOCK” setting in “WORK
SUPPORT”.BL-113
2. Check Intelligent Key warning buzzer.BL-138
3. Replace Intelligent Key unit.BL-160
Page 610 of 2896
INTELLIGENT KEY SYSTEM
BL-121
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
Take away warning chime (through window)
does not operate.1.Check “TAKE OUT FROM WINDOW WARN” setting in
“WORK SUPPORT”.BL-113
2. Check inside key antenna.BL-143
3. Check key switch.BL-124
4. Check Intelligent Key battery.BL-159
5. Check Intelligent Key warning chime.BL-156
6. Replace Intelligent Key unit.BL-160
Door lock operation warning buzzer does not
operate.1. Check door switch.BL-129
3. Check ignition knob switch.BL-127
4. Check door request switch.BL-132
5. Check back door request switch.BL-134
6. Check outside key antenna (driver side and passenger side).BL-139
7. Check outside key antenna (rear bumper).BL-141
8. Check inside key antenna.BL-143
9. Check Intelligent Key warning buzzer.BL-138
10 Replace Intelligent Key unit.BL-160
Symptom Diagnosis/service procedure Reference page
Page 619 of 2896
BL-130
INTELLIGENT KEY SYSTEM
Revision: June 20062007 Versa
2. CHECK DOOR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door switch and BCM.
3. Check continuity between door switch connector (B) B8 (front LH), B108 (front RH) terminal 2 or (C) B6
(rear LH), B116 (rear RH) terminal 1 or back door lock assembly connector (D) D405 terminal 3 and BCM
connectors (A) M18, M19 terminals 12, 13, 43, 47 and 48.
4. Check continuity between door switch connector (B) B8 (front
LH), B108 (front RH) terminal 2 or (C) B6 (rear LH), B116 (rear
RH) terminal 1 or back door lock assembly connector (D) D405
terminal 3 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR SWITCHES
FRONT AND REAR DOORS
Check continuity between front door switch terminal 2 or rear door
switch terminal 1 and exposed metal of switch while pressing and
releasing switch.
BACK DOOR
Check continuity between back door lock assembly connector (back
door switch) terminals 3 and 4 while pressing (closing back door)
and releasing (opening back door) switch.
OK or NG
OK1 >> (Front and rear doors) Switch circuit is OK.
OK2 >> (Back door) GO TO 4.
NG >> Replace door switch.1 - 13 : Continuity should exist.
1 - 48 : Continuity should exist.
2 - 12 : Continuity should exist.
2 - 47 : Continuity should exist.
3 - 43 : Continuity should exist.
1 - Ground : Continuity should not exist.
2 - Ground : Continuity should not exist.
3 - Ground : Continuity should not exist.
WIIA1244E
Door switch is released : Continuity should exist.
Door switch is pushed : Continuity should not exist.
PIIB6899E
When back door is open : Continuity should exist.
When back door is closed : Continuity should not exist.
WIIA1245E
Page 620 of 2896
INTELLIGENT KEY SYSTEM
BL-131
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
4. CHECK BACK DOOR SWITCH GROUND
Check continuity between back door lock assembly connector D405
terminal 4 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness.
5. CHECK BACK DOOR SWITCH SIGNAL FOR SHORT
1. Disconnect Intelligent Key unit.
2. Check continuity between BCM connector M18 terminal 30 and ground.
OK or NG
OK >> Back door switch circuit is OK.
NG >> Repair or replace harness.4 - Ground : Continuity should exist.
WIIA1246E
30 - Ground : Continuity should not exist.
WIIA1299E
Page 625 of 2896
BL-136
INTELLIGENT KEY SYSTEM
Revision: June 20062007 Versa
5. CHECK INTELLIGENT KEY UNIT OUTPUT SIGNAL
1. Connect Intelligent Key unit connector.
2. Check voltage between Intelligent Key unit connector M52 terminal 29 and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Replace Intelligent Key unit. Refer to BL-160, "
Removal
and Installation of Intelligent Key Unit" .
Unlock Sensor CheckEIS0092I
1. CHECK UNLOCK SENSOR INPUT SIGNAL
Check voltage between Intelligent Key unit connector and ground.
OK or NG
OK >> Unlock sensor circuit is OK.
NG >> GO TO 2.
2. CHECK UNLOCK SENSOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect Intelligent Key unit and front door lock actuator LH (door unlock sensor) connector.
3. Check continuity between Intelligent Key unit connector (A) terminal 28 and front door lock actuator LH
(door unlock sensor) connector (B) terminal 4.
4. Check continuity between Intelligent Key unit connector and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between Intelligent Key unit and front door lock actuator LH (door
unlock sensor).
Te r m i n a l s
Voltage (V)
(Approx.) (+)
(–)
Intelligent Key unit
connectorTerminal
M52 29 Ground 5
PIIB6617E
Te r m i n a l s
Front door
lock
(driver side)
conditionVoltage (V)
(Approx.) (+)
(–)
Intelligent Key
unit connectorTerminal
M52 28 GroundLocked 5
Unlocked 0
PIIB6638E
AB
Continuity
Intelligent Key
unit connectorTe r m i n a l Front door lock
actuator LH (door
unlock sensor)
connectorTe r m i n a l
M52 28 D3 4 Yes
A
GroundContinuity
Intelligent Key unit
connectorTe r m i n a l
M52 28 No
PIIB6639E
Page 626 of 2896
INTELLIGENT KEY SYSTEM
BL-137
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
3. CHECK UNLOCK SENSOR OPERATION
Check unlock sensor.
OK or NG
OK >> GO TO 4.
NG >> Replace unlock sensor.
4. CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock actuator LH (door unlock sensor) connector and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness.
5. CHECK INTELLIGENT KEY UNIT OUTPUT SIGNAL
1. Connect Intelligent Key unit harness connector.
2. Check voltage between Intelligent Key unit connector and ground.
OK or NG
OK >> Replace front door lock actuator LH (door unlock sen-
sor). Refer to BL-169, "
Removal and Installation" .
NG >> Replace Intelligent Key unit. Refer to BL-160, "
Removal
and Installation of Intelligent Key Unit" .
Terminal
Driver side door
conditionContinuity
Unlock sensor
45Lock No
Unlock Yes
PIIB6643E
Front door lock actua-
tor LH (door unlock
sensor) connectorTe r m i n a l
GroundContinuity
D3 5 Yes
PIIB6644E
Te r m i n a l s
Voltage (V)
(Approx.) (+)
(–)
Intelligent Key unit
connectorTe r m i n a l
M52 28 Ground 5
PIIB6638E
