2007 NISSAN FRONTIER ECU

steering wheel switches for audio control
(if so equipped)
 Press the POWER button to turn the audio system on or
off.
 To choose preset radio stations A, B, C, CD and AUX
press MODE repeatedly.
 The tuning up or down switch can be used to perform
the following:
• Push the
switch for less than 1.5 seconds to change to a preset station.
• Push and hold the
switch for more than 1.5 seconds to seek the next or previous

broadcasting radio station.
• Push the
switch while playing a CD (if so equipped) for less than 1.5 seconds to

change tracks on the CD.
• If the vehicle is equipped with a CD changer, push and hold the
switch for more

than 1.5 seconds to change between CDs.
utilit Y Bed with sPra Y-on B ed liner
and utili -trac K ™ sY ste M (if so equipped)
The Utili-track™ channel system allows you to move
tie-down clamps in the bed to the best location to
secure a load.
 The tie-down cleats must be installed so the
clamp is properly seated in the notches in the
rail. If the tie-down cleat is not seated in the
notches, it will not be flush with the rail and
cannot be properly tightened. The bolt in the center of the cleat must be tightened
hand-tight (20 – 40 inch pounds).
 Check the tightness of the tie-down cleat periodically during a trip to make sure the
center bolt has not become loose.
 The channel end stoppers can be used to help prevent cargo from sliding or shifting
off the end of the truck bed. They must be installed so they are properly seated in the
detents in the channel.
Refer to your Owner’s Manual for loading limits and tie-down recommendations.
instru Ment B rightness control/tri P
change B utton
The instrument brightness control operates when the
headlight control switch is in the or position.
Turn the control to adjust the brightness of the
instrument panel lights.
Press the change button to select trip computer
features. See “Trip Computer” in the next column of this
Quick Reference Guide for more information.

seat Belt warning light and chiMe
 The light and chime remind you to fasten your seat belts. The
light illuminates whenever the ignition key is turned to the ON
or START position and remains illuminated until the driver’s
seat belt is fastened. At the same time, the chime sounds
for approximately 6 seconds unless the driver’s seat belt is
securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied. For 7 seconds after the
ignition switch is in the ON position, the system does not activate the warning light
for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.
tire Pressure Monitoring s Y ste M (tPM s)
This system monitors tire pressure. Please remember, this system
does not detect a sudden drop in tire pressure (for example, a
blowout while driving). It also does not monitor the air pressure in
the spare tire.
Tire pressure is affected by temperature. Low outside temperature
causes lower tire pressure. This may cause the low tire pressure
warning light to illuminate.
If the low tire pressure warning light illuminates, check the tire pressure in all four tires.
To turn the low tire pressure warning light off, adjust the low tire pressure to the
recommended COLD tire pressure shown on the Tire and Loading Information label
located in the driver’s door opening.
If TPMS is not functioning properly, the low tire pressure warning light will flash for
approximately 60 seconds when the key is turned on. After 60 seconds, the light will
remain on. Have the system checked by a NISSAN dealer.
child safet Y rear door loc K
( c rew cab Model only)
Child safety locks help prevent the rear doors from being opened
accidentally, especially when small children are in the vehicle. The
child safety lock levers are located on the edge of the rear doors.
When the lever is in the LOCK position, the door can be opened
only from the outside.

fold flat front P assenger seat
(if so equipped)
To fold the front passenger’s seatback flat for extra
storage length when transporting long items:
 Slide the seat to the rearmost position. Lift up on
the recline lever, located on the outside edge of
the seat, and fold the seatback forward as far as
it will go. 01 Then lift up on the latch located on the upper corner of the seatback to
release the back of the seat. 02
0201
folding the rear B ench seat
( c rew cab Model only)
FOLDING THE SEATBACK DOWN :
To fold the rear bench seatback down to access the
jacking tools, pull up on the straps 01 located on the
outer edge of the seatbacks and fold the seatback
forward.
FOLDING THE SEAT BASE UP:
To fold the rear bench seat base up to access the
under-seat storage bins:
 Lift up on the lever 02 located on the side of the
seat, while lifting up the front of the seat cushion.
 Fold the bottom of the seat cushion toward the
back of the vehicle until it locks into place.
 Repeat this process to raise and secure the seat
cushion on the other side of the vehicle.
01
02