2007 NISSAN 350Z battery

SRS-48
CRASH ZONE SENSOR
Revision: 2006 November2007 350Z
CRASH ZONE SENSORPFP:98531
Removal and InstallationNHS0000X
REMOVAL
CAUTION:

Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.

Do not use air tools or electric tools for servicing.
1. Remove crash zone sensor connector.
2. Remove crash zone sensor fixing nuts.
CAUTION:

Replace crash zone sensor if it has been dropped or sustained an impact.

Do not disassemble crash zone sensor.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Check crash zone sensor for proper installation.

After the work is complete, perform self-diagnosis to make sure that no malfunction is detected.
Refer to SRS-27, "
SRS Operation Check (USER MODE)" .
PHIA0172E

SIDE AIR BAG (SATELLITE) SENSOR
SRS-49
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: 2006 November2007 350Z
SIDE AIR BAG (SATELLITE) SENSORPFP:98830
Removal and InstallationNHS0000Y
REMOVAL
CAUTION:

Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.

Do not use air tools or electric tools for servicing.
1. Remove seat belt pre-tensioner. Refer to SB-4, "
Removal and Installation of Seat Belt (Coupe)" or SB-6,
"Removal and Installation of Seat Belt (Roadster)" .
2. Remove side air bag (Satellite) sensor fixing nuts.
3. Remove the side air bag (Satellite) sensor connector.
CAUTION:

Do not use old nuts; replace with new ones.

Check side air bag (Satellite) sensor to ensure it is free of deformities, dents, cracks or rust. If it
shows any visible signs of damage, replace it with new one.

Do not attempt to disassemble side air bag (Satellite) sensor.

Replace side air bag (Satellite) sensor if it has been dropped or sustained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Check side air bag (Satellite) sensor for proper installation.

After replacement of side air bag (Satellite) sensor, perform self-diagnosis to make sure that no
malfunction is detected. Refer to SRS-27, "
SRS Operation Check (USER MODE)" .
PHIA0176E

DIAGNOSIS SENSOR UNIT
SRS-51
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: 2006 November2007 350Z
DIAGNOSIS SENSOR UNITPFP:28556
Removal and InstallationNHS00010
REMOVAL
CAUTION:

Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.

Do not use air tools or electric tools for servicing.
1. Disconnect each harness connector for the air bag module and seat belt pre-tensioner.
2. Remove center console. Refer to IP-11, "
Removal and Installation" .
3. Disconnect diagnosis sensor unit connector.
4. Remove fixing bolts from the diagnosis sensor unit.
CAUTION:

Do not use old bolts. Replace with new ones.

Check diagnosis sensor unit bracket to ensure it is free of deformities, dents, cracks or rust. If it
shows any visible signs of damage, replace with new one.

Replace diagnosis sensor unit if it has been dropped or sustained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Check the diagnosis sensor unit for proper installation.

After replacement of diagnosis sensor unit, perform self-diagnosis to make sure that no malfunc-
tion is detected. Refer to SRS-27, "
SRS Operation Check (USER MODE)" .
ECU DISCRIMINATED NO.
After replacing the diagnosis sensor unit, make sure that the diagnosis sensor unit identification is correct for
the vehicle as equipped.Hex bolt: 24.5 N·m (2.5 kg-m, 18 ft-lb)
Ground bolt: 6.9 N·m (0.7 kg-m, 61 in-lb)
PHIA0463E
Model Specification ECU DISCRIMINATED No.
CoupeModels with driver and passenger air bags and seat belt pre-tensioner FAE6
Models with driver and passenger air bags, seat belt pre-tensioner, side air bags and curtain
air bagsFAE4
RoadsterModels with driver and passenger air bags and seat belt pre-tensioner FAE7
Models with driver and passenger air bags, seat belt pre-tensioner and side air bags FAE5