2007 NISSAN 350Z drain bolt

MT-2
PRECAUTIONS
Revision: 2006 November2007 350Z
PRECAUTIONSPFP:00001
Precautions for Battery ServiceNCS0000N
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Notice or PrecautionsNCS0000O

If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder)
body and CSC tube . Return CSC body insert to original position to remove transmission assembly. Dust
on clutch disc sliding parts may damage seal of CSC body and may cause clutch fluid leakage.

Do not reuse transmission oil, once it has been drained.

Check oil level or replace oil with vehicle on level ground.

During removal or installation, keep inside of transmission clear of dust or dirt.

Check for the correct installation status prior to removal or disassembly. If matching marks are required,
be certain they do not interfere with the function of the parts they are applied to.

In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If
tightening sequence is specified, observe it.

Be careful not to damage sliding surfaces and mating surfaces.

Do not hold control lever housing to prevent bushing of control lever housing from deformation when mov-
ing transmission assembly.

MT-22
TRANSMISSION ASSEMBLY
Revision: 2006 November2007 350Z
Disassembly and AssemblyNCS00011
COMPONENTS
Case Components
1. Breather tube 2. Bracket 3. Filler plug
4. Gasket 5. Front cover oil seal 6. Front cover
7. Front cover gasket 8. Transmission case 9. Drain plug
10. Baffle plate 11. Sliding ball bearing 12. Magnet
13. Dowel pin 14. Bushing 15. Main shaft bearing retainer
16. Adapter plate 17. Oil gutter
A. Seal lip
Refer to GI-11, "
Components" and the followings for the symbols in the figure.
: Apply multi-purpose grease.
: Apply Genuine Silicone RTV or an equivalent. Refer to GI-45, "
Recommended Chemical Products and Sealants" .
: Apply Genuine Medium Strength Thread Locking Sealant or an equivalent. Refer to GI-45, "
Recommended Chemical
Products and Sealants" .
: For the bolt mounting positions, Refer to MT-56, "
Case Components" .
PCIB1917E

MT-30
TRANSMISSION ASSEMBLY
Revision: 2006 November2007 350Z
18. Remove baffle plate mounting nut from the transmission case.
19. Remove snap ring from the main drive gear bearing, using snap
ring pliers.
20. Using a soft hammer to carefully tap main shaft and counter
shaft from the transmission case side, and then separate
adapter plate and transmission case.
21. Remove counter front bearing from the transmission case.
22. Remove oil gutter and breather tube from the transmission case.
23. Remove filler plug, drain plug, and gaskets from transmission
case.
24. Remove bracket mounting bolt and then remove bracket from
transmission case.
SCIA1443E
SCIA1532E
SCIA1687E
PCIB0436E

MT-60
TRANSMISSION ASSEMBLY
Revision: 2006 November2007 350Z
30. Install check ball and check select spring into the rear extension.
31. Install rear extension upper cover gasket and rear extension
upper cover to rear extension.
CAUTION:

Do not reuse rear extension upper cover gasket.

Avoid tangling check select spring.
32. Tighten rear extension upper cover bolts to the specified torque
in order as shown in the figure. Refer to MT-22, "
Case Compo-
nents" .
33. Install gasket to drain plug and then install it to transmission
case. Tighten drain plug to the specified torque. Refer to MT-22,
"Case Components" .
CAUTION:
Do not reuse gasket.
34. Install gasket to filler plug and then install it to transmission case. Tighten filler plug to the specified torque.
Refer to MT-22, "
Case Components" .
CAUTION:

Do not reuse gasket.

After oil is filled, tighten filler plug to specified torque.
PCIB0599E
PCIB0257E