2007 NISSAN 350Z mirror

LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z System Description .............................................. 103
OUTLINE ........................................................... 103
OPERATION BY LIGHTING SWITCH .............. 104
COMBINATION SWITCH READING FUNCTION . 104
EXTERIOR LAMP BATTERY SAVER CONTROL . 104
CAN Communication System Description ............ 105
CAN Communication Unit .................................... 105
Schematic ............................................................ 106
Wiring Diagram — TAIL/L — ................................ 107
Terminals and Reference Values for BCM ............ 112
Terminals and Reference Values for IPDM E/R .... 114
How to Proceed With Trouble Diagnosis ............... 114
Preliminary Check ................................................. 114
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................... 114
CONSULT-III Function (BCM) ............................... 115
CONSULT-III Function (IPDM E/R) ....................... 115
Parking, License Plate, Side Marker and Tail Lamps
Do Not Illuminate (for USA) ................................... 116
Parking, License Plate, Side Marker, and Tail Lamps
Do Not Illuminate (for Canada) ............................. 119
Parking, Side Marker, License Plate and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ....... 124
License Plate Lamp .............................................. 125
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................. 125
Front Parking Lamp .............................................. 125
BULB REPLACEMENT ..................................... 125
REMOVAL AND INSTALLATION ...................... 125
Tail Lamp .............................................................. 125
BULB REPLACEMENT ..................................... 125
REMOVAL AND INSTALLATION ...................... 125
REAR COMBINATION LAMP ................................ 126
Bulb Replacement ................................................ 126
REAR FENDER SIDE (STOP & TAIL LAMP,
REAR SIDE MARKER LAMP) .......................... 126
REAR BUMPER SIDE (BACK-UP LAMP BULB,
REAR TURN SIGNAL LAMP BULB) ................. 126
Removal and Installation ...................................... 127
REMOVAL ......................................................... 127
INSTALLATION ................................................. 127
INTERIOR ROOM LAMP ........................................ 128
Component Parts and Harness Connector Location . 128
System Description .............................................. 128
POWER SUPPLY AND GROUND .................... 129
SWITCH OPERATION ...................................... 130
MAP LAMP TIMER OPERATION ..................... 130
INTERIOR LAMP BATTERY SAVER CONTROL . 131
Schematic ............................................................ 132Wiring Diagram — ROOM/L — ............................133
COUPE MODELS .............................................133
ROADSTER MODELS ......................................137
Terminals and Reference Values for BCM ............141
How to Proceed with Trouble Diagnosis ...............141
Preliminary Check ................................................142
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................142
CONSULT-III Function (BCM) ..............................143
WORK SUPPORT .............................................143
DATA MONITOR ...............................................143
ACTIVE TEST ...................................................144
Map Lamp Control Does Not Operate (Coupe mod-
els) ........................................................................144
Map Lamp Control Does Not Operate (Roadster
models) .................................................................146
Ignition Key Hole Illumination Does Not Illuminate .148
Luggage Room Lamp Does Not Illuminate (Coupe
Models) .................................................................149
Trunk Room Lamp Does Not Illuminate (Roadster
Models) .................................................................151
Bulb Replacement ................................................153
MAP LAMP ........................................................153
VANITY MIRROR LAMP ...................................154
LUGGAGE ROOM LAMP & TRUNK ROOM
LAMP .................................................................154
IGNITION KEY HOLE ILLUMINATION ..............154
Removal and Installation ......................................155
MAP LAMP ........................................................155
LUGGAGE ROOM LAMP ..................................155
ILLUMINATION .......................................................156
System Description ...............................................156
OUT LINE ..........................................................156
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................157
EXTERIOR LAMP BATTERY SAVER CONTROL .158
CAN Communication System Description ............158
CAN Communication Unit .....................................158
Schematic .............................................................159
Wiring Diagram — ILL — ......................................161
Bulb Replacement ................................................171
LUGGAGE FLOOR BOX LAMP ........................171
CUP HOLDER ILLUMINATION .........................171
Removal and Installation ......................................171
LUGGAGE FLOOR BOX LAMP ........................171
BULB SPECIFICATIONS ........................................172
Headlamp .............................................................172
Exterior Lamp .......................................................172
Interior Lamp/Illumination .....................................172

INTERIOR ROOM LAMP
LT-129
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
POWER SUPPLY AND GROUND
Power is supplied at all times

through 10A fuse [No.21, located in fuse block (J/B)]

to key switch terminal 2,

through 10A fuse [No.18, located in fuse block (J/B)]

to BCM terminal 42,

through 40A fusible link (letter F, located in fuse, fusible link and relay box)

to BCM terminal 55.
When key is removed from ignition key cylinder, power is interrupted

through key switch terminal 1

to BCM terminal 37.
With ignition switch in ON or START position, power is supplied

through 10A fuse [No.1, located in fuse block (J/B)]

to BCM terminal 38.
When map lamp and vanity mirror lamp power is supplied at times

through BCM terminal 41

to ignition key hole illumination terminal1

to map lamp terminal 3 (Coupe models)

to map lamp terminal 2 (Roadster models)

to luggage room lamp terminal 1 (Coupe models)

to trunk room lamp terminal 1 (Roadster models) and

to vanity mirror lamp LH and RH terminals 1.
Ground is supplied

to BCM terminal 52

through grounds M30 and M66.
When driver side door is opened, ground is supplied

through case ground of driver side door switch

to BCM terminal 62.
When passenger side door is opened, ground is supplied

through case ground of passenger side door switch

to BCM terminal 12.
When back door is opened, ground is supplied (Coupe models)

through grounds B5, B6, D105 and T14

to back door switch terminal 3

through back door switch terminal 1

to BCM terminal 58.
When trunk lid is opened, ground is supplied (Roadster models)

through grounds B5, B6 and T14

to trunk lid lock assembly (trunk room lamp switch) terminal 1

through trunk lid lock assembly (trunk room lamp switch) terminal 3

to BCM terminal 57.
When the driver side door or passenger side door is unlocked by door lock and unlock switch, The BCM
receives unlock signal with power window serial link

through grounds M30 and M66

to power window main switch (door lock and unlock switch) terminal 15 or power window sub switch (door
lock and unlock switch) terminal 11

through power window main switch (door lock and unlock switch) terminal 12 and power window sub
switch (door lock and unlock switch) terminal 16

to BCM terminal 22.

LT-130
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
When the driver side door is unlocked by door key cylinder switch, The BCM receives information by commu-
nicating with power window main switch

through grounds M30 and M66

to door key cylinder switch terminal 2

through door key cylinder switch terminal 1

to power window main (door lock and unlock switch) switch terminal 7

through power window main switch (door lock and unlock switch) terminal 12

to BCM terminal 22.
When a signal, or combination of signals is received by BCM, ground is supplied

through BCM terminal 48

to map lamp terminal 2 (Coupe models)

to map lamp terminal 3 (Roadster models).
With power and ground are supplied, map lamp illuminates.
SWITCH OPERATION
When map lamp switch is ON, ground is supplied

to map lamp terminal 1 (Coupe models)

to map lamp terminal 1 (Roadster models)

through grounds M30 and M66.
And power is supplied

through BCM terminal 41

to ignition key hole illumination terminal 1

to map lamp terminal 3 (Coupe models)

to map lamp terminal 2 (Roadster models).
When vanity mirror lamp LH and RH is ON, ground is supplied

to vanity mirror lamp LH and RH terminals 2

through grounds M30 and M66.
And power is supplied

through BCM terminal 41

to vanity mirror lamp terminal 1.
MAP LAMP TIMER OPERATION
When the map lamp switch is in the DOOR position, and when all conditions below are met, BCM performs
timer control (maximum 30 seconds) for map lamp ON/OFF.
In addition, when map lamp turns ON or OFF there is gradual brightening or dimming over 1 second.
Power is supplied at all times

to 10A fuse [No. 21 located in fuse block (J/B)]

through key switch terminal 2.
When all doors are closed (all door switches OFF) and key is removed from key cylinder (key switch OFF),
power will not be supplied to BCM terminal 37.
Ground is supplied

through BCM terminal 22

to power window main switch (door lock and unlock switch) terminal 12.
At this time, BCM detects that driver door is unlocked. It determines that map lamp timer operation conditions
are met, and turns map lamp ON for 30 seconds.
When all doors are closed (all door switches OFF) and key is in key cylinder (key switch ON),
Power is supplied

through key switch terminal 1

to BCM terminal 37.
When the key is removed from key switch (key switch OFF), power supply to BCM terminal 37 is terminated.
BCM detects that key has been removed. It determines that map lamp timer conditions are met, and turns
map lamp ON for 30 seconds.

INTERIOR ROOM LAMP
LT-131
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
When driver door opens → closes, and key is not inserted in key switch (key switch OFF), BCM terminal 62
changes between 0V (door open) → 5V (door closed). BCM determines that conditions for spot lamp opera-
tion are met and turns interior lamp ON for 30 seconds.
Timer control is canceled under the following conditions.

Driver door is locked (When locked key fob or power window main switch (door lock and unlock switch,
door key cylinder switch).

Driver door is opened (driver door switch turns ON).

Ignition switch ON.
INTERIOR LAMP BATTERY SAVER CONTROL
If the room lamp remains illuminated by door switch open signal, or if room lamp switch is in the ON position
for more than 30 minutes after the ignition switch is turned to the OFF position, BCM will automatically turn off
map lamp, luggage room lamp (Coupe models), trunk room lamp (Roadster models) and vanity mirror lamp.
After lamps turn OFF by battery saver system, the lamps illuminate again when

signal from key fob, door lock and unlock switch, or key cylinder is locked or unlocked,

door is opened or closed,

key is removed from ignition key cylinder or inserted in ignition key cylinder.
Interior lamp battery saver control period can be changed by the function setting of CONSULT-III.

LT-154
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
VANITY MIRROR LAMP
1. Insert a thin screwdriver in the lens end and remove lens.
2. Remove bulb.
3. Installation is the reverse order of removal.
LUGGAGE ROOM LAMP & TRUNK ROOM LAMP
Luggage Room Lamp (Coupe Models)
1. Remove luggage room lamp. Refer to LT- 1 5 5 , "Removal and Installation" .
2. Remove bulb.
3. Installation is the reverse order of removal.
Trunk Room Lamp (Roadster Models)
1. Unfold pawl A and remove lens.
2. Remove trunk room lamp while pressing pawl B in the direction
of the arrow.
3. Disconnect trunk room lamp connector.
4. Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION
1. Remove instrument lower driver panel. Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket to left to release lock and remove bulb socket
(1).
3. Remove ignition key illumination bulb (2) from its socket.
4. Installation is the reverse order of removal.Vanity mirror lamp : 12V - 1.32W
PKIA7806E
Luggage room lamp : 12V - 5W
PKIA1885E
Trunk room lamp : 12V - 3.4W
PKIA0182E
Ignition key hole illumination : 12V - 1.4W
PKIC4830J

LT-172
BULB SPECIFICATIONS
Revision: 2006 November2007 350Z
BULB SPECIFICATIONSPFP:26297
HeadlampNKS00505
Exterior LampNKS00506
Interior Lamp/IlluminationNKS00507
Item Wattage (W)
High / Low35 (D2R)
Item Wattage (W)
Front combination lampFront turn signal lamp/— 28/8 (amber)
Parking lamp 5
Front side marker lamp LED
Rear combination lampStop/Tail lamp LED
Rear turn signal lamp 21 (amber)
Back-up lamp 21
Rear side marker lamp LED
License plate lamp5
High-mounted stop lampLED
Item Wattage (W)
Luggage floor box lamp1.4
Cup holder illumination lamp1.1
Bottle holder illumination lampLED
Map lamp8
Luggage room lamp5
Trunk room lamp3.4
Vanity mirror lamp1.32
Ignition key hole illumination lamp1.4