2007 NISSAN 350Z oil

FRONT DISC BRAKE
BR-35
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
5. Install the torque member to the steering knuckle and tighten the
mounting bolts to the specified torque. Refer to BR-27, "
Compo-
nents" .
CAUTION:
Before installing torque member to vehicle, wipe off oil and
grease on the washer seats on steering knuckle and the
mounting surface of the torque member.
6. Install pad retainers to torque member.
7. Press in piston until pads can be installed, and then install cylin-
der body to torque member.
8. Install cylinder body, and tighten sliding pin bolt to the specified
torque. Refer to BR-27, "
Components" .
9. Position a projection of brake hose metal fitting by aligning with protrusions on cylinder body and tighten
union bolt to specified torque. Refer to BR-12, "
Hydraulic Circuit" .
CAUTION:

Assemble brake hose securely to cylinder body.

Do not reuse copper washer for union bolts.
10. After installing caliper assembly, refill with new brake fluid and bleed air. Refer to BR-11, "
Bleeding Brake
System" .
DISC ROTOR INSPECTION
Visual Inspection
Check surfaces of disc rotor for uneven wear, cracks, and serious damage. If a malfunction is detected,
replace applicable part.
Runout Inspection
1. Using wheel nuts, secure disc rotor to wheels hub. (2 or more positions)
2. Using a dial indicator, check runout.
NOTE:
Make sure that wheel bearing axial end play is with in the speci-
fication before measuring runout. Refer to FA X - 4 , "
On-Vehicle
Inspection" .
3. If runout is outside limit, find the minimum runout point by shift-
ing the mounting positions of disc rotor and wheel hub by one hole.
4. If runout is still outside the limit after performing the above operation, replace or lathe the disc rotor.
[When lathing, use the Pro–Cut PFM On–Car Brake Lathe (Tool No. 38–PFM90.5) or equivalent.]
Thickness Inspection
Using a micrometer, check thickness of disc rotor. If thickness is out-
side standard, replace disc rotor.
SBR557E
Measurement point:
At a point 10.0 mm (0.394 in) from outer edge of disc
Runout limit (with it attached to the vehicle):
0.035 mm (0.0014 in) or less
SBR019B
Standard thickness : 28.0 mm (1.10 in)
Repair limit thickness : 26.0 mm (1.02 in)
Maximum uneven wear (measured at 8 positions)
: 0.015 mm (0,0006 in) or less
SBR020B

BR-36
FRONT DISC BRAKE
Revision: 2006 November2007 350Z
Disassembly and Assembly of Brake Caliper Assembly (With Brembo Calipers)NFS0000Y
DISASSEMBLY
1. Insert a piece of wood as shown in the figure, blow air in through
the flare nut mounting hole, and remove the piston and piston
boot. If the four pistons do not all come out at the same time,
press the piston(s) that have come out a ways into the cylinder
body and blow air in again.
CAUTION:
Do not get fingers caught in the piston.
2. Remove the piston boot from the piston.
3. Using a flat-bladed screwdriver, remove the piston seal.
CAUTION:

Be careful not to damage cylinder inner wall.

Never remove the four bolts from the inner and outer
sides of the caliper. Do not tighten them further, either.
CALIPER INSPECTION
Caliper
CAUTION:

Use new brake fluid to clean. Do not use mineral oils such as gasoline or kerosene.

Check for corrosion, wear, or damage to the cylinder inner wall, and replace the caliper if there are
any non-standard conditions.
Piston
CAUTION:

Since the piston surface is plated, do not repair using sandpaper.

Check piston surface for corrosion, wear, and damage. If any non-standard condition is detected,
replace applicable part.
ASSEMBLY
1. Apply polyglycol ether based lubricant to the piston seal, and
install them to the cylinder body.
BRB0261D
PFIA0270E
PFIA0271E

BR-44
REAR DISC BRAKE
Revision: 2006 November2007 350Z
CAUTION:
Attach the pad with wear sensor to the outer side.
3. Insert the upper pad pin from the outer cylinder side, then insert
firmly to the inner cylinder side through the hole in the top of the
pad.
4. As shown in the figure, place the top of the cross spring over the
top pad pin, press in the cross spring, push the lower pad pin
from the outer cylinder side to the inner cylinder side, and
secure the cross spring.
5. Insert the clip in the small hole at the end of the pad pin.
CAUTION:
If the clip is not fully attached, the pad pin or the pad could
fall out while the vehicle is in motion.
6. Install tires to vehicle.
Removal and Installation of Brake Caliper Assembly (Other than Brembo Cali-
pers)
NFS00012
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Fasten disc rotor using wheel nut.
3. Drain brake fluid. Refer to BR-10, "
Drain and Refill" .
4. Remove union bolts then disconnect brake hose from caliper
assembly and torque member bolts, and remove caliper assem-
bly.
CAUTION:
Do not drop brake pad.
5. Remove disc rotor.
CAUTION:
Put matching marks on wheel hub assembly and disc rotor,
if it is necessary to remove disc rotor.
INSTALLATION
CAUTION:

Refill with new brake fluid “DOT 3”.

Do not reuse drained brake fluid.
1. Install disc rotor.
CAUTION:
Put alignment marks on disc rotor and wheel hub at the time of removal when reusing disc rotor.
2. Install caliper assembly to the vehicle, and tighten torque member mounting bolts to the specified torque.
CAUTION:
Before installing caliper assembly to the vehicle, wipe off oil and grease on washer seats on axle
assembly and mounting surface of caliper assembly.
3. Install L-shape pin of brake hose to caliper assembly and tighten union bolts to the specified torque.
CAUTION:

Do not reuse the copper washer for union bolts.

Securely attach brake hose to protrusion on caliper assembly.
4. Insert new brake fluid and bleed air. Refer to BR-11, "
Bleeding Brake System" .
5. Check rear disc brake for drag.
6. Install tires to vehicle.
BRD0352D
PFIA0292J

BR-46
REAR DISC BRAKE
Revision: 2006 November2007 350Z
3. As shown in the figure, using a flat-bladed screwdriver, remove
the retaining ring from the cylinder body.
4. Place a wooden block as shown in the figure, and blow air from
union bolt mounting hole to remove pistons and piston boots.
CAUTION:
Do not get fingers caught in the piston.
5. Using a flat-bladed screwdriver, remove piston seals from cylin-
der body.
CAUTION:
Be careful not to damage cylinder inner wall.
CALIPER INSPECTION
Cylinder Body
CAUTION:

Use new brake fluid to clean. Never use mineral oils such as gasoline or kerosene.

Check inner wall of cylinder for corrosion, wear, and damage. If any non-standard condition is
detected, replace cylinder body.

Minor flaws caused by corrosion or a foreign material can be removed by polishing the surface
with a fine sandpaper. Replace the cylinder body, if necessary.
To r q u e M e m b e r
Check for wear, cracks, and damage. If damage or deformation is present, replace the affected part.
Piston
CAUTION:
Since the piston surface is plated, do not repair using sandpaper.
Check piston surface for corrosion, wear, and damage. If any non-standard condition is detected, replace
applicable part.
Sliding Pin Bolts and Sliding Pin Boots
Check that there is no wear, damage, or cracks in the sliding pin bolts and sliding pin boots, and if there are,
replace them.
SBR028A
BRD0041D
SFIA0999E

REAR DISC BRAKE
BR-49
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
Disassembly and Assembly of Brake Caliper Assembly (With Brembo Calipers)NFS00018
DISASSEMBLY
1. Insert a piece of wood as shown in the figure, blow air in through
the flare nut mounting hole, and remove the piston and piston
boot.
CAUTION:
Do not get fingers caught in the piston.
2. Remove the piston boot from the piston.
3. Using a flat-bladed screwdriver, remove the piston seal.
CAUTION:

Be careful not to damage cylinder inner wall.

Never remove the four bolts from the inner and outer
sides of the caliper. Do not tighten them further, either.
CALIPER INSPECTION
Caliper
CAUTION:

Use new brake fluid to clean. Never use mineral oils such as gasoline or kerosene.

Check for corrosion, wear, or damage to the cylinder inner wall, and replace the caliper if there are
any non-standard conditions.
Piston
CAUTION:

Since the piston surface is plated, do not repair using sandpaper.

Check piston surface for corrosion, wear, and damage. If any non-standard condition is detected,
replace applicable part.
ASSEMBLY
1. Apply polyglycol ether based lubricant to the piston seal (1), and
install them to the cylinder body.
CAUTION:
Do not reuse piston seal.
PFIA0281E
SFIA1321E
PFIA0872E