2007 NISSAN 350Z ignition

BL-148
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: 2006 November2007 350Z
Diagnostic Procedure 4NIS00038
CHECK VEHICLE SECURITY HORN ALARM
First perform the “SELF-DIAG RESULTS” of “BCM” with CONSULT-III, then perform the trouble diag-
nosis of malfunction system indicated in “SELF-DIAG RESULTS” of “BCM”. Refer to BCS-16, "
CAN
Communication Inspection Using CONSULT-III (Self-Diagnosis)" .
1. CHECK HORN OPERATION
Check if horn sounds with horn switch.
Does horn operate?
YES >> GO TO 2.
NO >> Check horn circuit. Refer to WW-53, "
HORN" .
2. CHECK IPDM E/R INPUT SIGNAL
Check voltage between IPDM E/R connector E9 terminal 51 and ground.
OK or NG
OK >> Replace IPDM E/R.
NG >> GO TO 3.
3. CHECK HORN RERAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and horn relay connector.
3. Check continuity between IPDM E/R harness connector E9 terminal 51 and horn relay harness connector
E21 terminal 1.
OK or NG
OK >> Horn circuit is OK.
NG >> Repair or replace harness.
Diagnostic Procedure 5NIS00039
CHECK VEHICLE SECURITY HEADLAMP ALARM
1. CHECK HEAD LAMP OPERATION
Does headlamp come on when turning lighting switch “ON”?
YES or NO
YES >> Headlamp alarm circuit is OK.
NO >> Check headlamp system. Refer to,,, LT- 3 2 , "
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM -"LT- 5 , "HEADLAMP (FOR USA)" . 51 (G/B) – Ground : Battery voltage.
PIIA6403E
1 (G/B) - 51(G/B) : Continuity should exist.
PIIA6404E

NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-151
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
System DescriptionNIS0003C
NVIS (Nissan Vehicle Immobilizer System-NATS) has the following immobilizer functions:

Since only NVIS (NATS) ignition keys, whose ID Nos. have been registered into the ECM and BCM, allow
the engine to run, a vehicle operation without a key registered in NVIS (NATS) is prevented by NVIS
(NATS).
That is to say, NVIS (NATS) will immobilize the engine if someone tries to start it without the registered
key of NVIS (NATS).

All of the originally supplied ignition key IDs (except for card plate key) have been registered in NVIS
(NATS).
If requested by the vehicle owner, a maximum of five key IDs can be registered into the NVIS (NATS)
components.

The security indicator blinks when the ignition switch is in “OFF” or “ACC” position. Therefore, NVIS
(NATS) warns outsiders that the vehicle is equipped with the anti-theft system.

When NVIS (NATS) detects trouble, the security indicator lamp lights up while ignition key is in the “ON”
position.

NVIS (NATS) trouble diagnoses, system initialization and additional registration of other NVIS (NATS)
ignition key IDs must be carried out using CONSULT-III hardware and CONSULT-III NVIS (NATS) soft-
ware.
When NVIS (NATS) initialization has been completed, the ID of the inserted ignition key is automatically
registered in NVIS (NATS). Then, if necessary, additional registration of other NVIS (NATS) ignition key
IDs can be carried out.
Regarding the procedures of NVIS (NATS) initialization and NVIS (NATS) ignition key ID registration, refer
to CONSULT-III Operation Manual NATS-IVIS/NVIS.

When servicing a malfunction of the NVIS (NATS) (indicated by lighting up of Security Indicator
Lamp) or registering another NVIS (NATS) ignition key ID No., it may be necessary to re-register
original key identification. Therefore, be sure to receive ALL KEYS from vehicle owner.

BL-152
NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2006 November2007 350Z
System CompositionNIS0003D
The immobilizer function of the NVIS (NATS) consists of the following:

NATS ignition key

NATS antenna amp. located in the ignition key cylinder

BCM

Engine control module (ECM)

Security indicator
NOTE:
The communication between ECM and BCM uses the CAN communication system.
ECM Re-communicating FunctionNIS0003E
Performing following procedure can automatically perform re-communication of ECM and BCM, but only
when the ECM has been replaced with a new one (*1).
*1: New one means a virgin ECM which has never been energized on-board.
(In this step, initialization procedure by CONSULT-III is not necessary)
NOTE:

When registering new Key IDs or replacing the ECM other than brand new, refer to CONSULT-III
Operation Manual NATS-IVIS/NVIS.

If multiple keys are attached to the key holder, separate them before work.

Distinguish keys with unregistered key ID from those with registered ID.
1. Install ECM.
2. Using a registered key (*2), turn ignition switch to “ON”.
*2: To perform this step, use the key (except for card plate key) that has been used before performing
ECM replacement.
3. Maintain ignition switch in “ON” position for at least 5 seconds.
4. Turn ignition switch to “OFF”.
5. Start engine.
If engine can be started, procedure is completed.
If engine cannot be started, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS and initialize control
unit.
PIIA1121E

BL-154
NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2006 November2007 350Z
Terminals and Reference Value for BCMNIS0003G
CONSULT-IIINIS0003H
CONSULT-III INSPECTION PROCEDURE
Refer to “CONSULT-III Operation Manual NATS-IVIS/NVIS”.
CONSULT-III DIAGNOSTIC TEST MODE FUNCTION
NOTE:

When any initialization is performed, all ID previously registered will be erased and all NATS ignition keys
must be registered again.
NVIS (NATS) SELF-DIAGNOSTIC RESULTS ITEM CHART
Te r m i -
nal Wire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
21 G/W NATS antenna amp.Input/
OutputIgnition switch (OFF → ON)Just after turning ignition switch “ON”:
Pointer of tester should move.
23 G/OR Security indicator lamp OutputGoes OFF → illuminates
(Every 2.4 seconds)Battery voltage → 0
25 BR NATS antenna amp.Input/
OutputIgnition switch (OFF → ON)Just after turning ignition switch “ON”:
Pointer of tester should move.
38 W/L Ignition switch (ON) InputIgnition switch
(ON or START)Battery voltage
39 L CAN-HInput/
Output——
40 P CAN-LInput/
Output——
42 GY Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
55 R Power source (Fusible link) Input — Battery voltage
CONSULT-III DIAGNOSTIC TEST
MODEDescription
C/U INITIALIZATIONWhen replacing any of the following components, C/U initialization and re-registration of all
NATS ignition keys are necessary.
[(NATS ignition key BCM/ ECM)
Detected items
[NVIS (NATS) program card screen
terms]P No. Code
(Self-diagnostic
result of
“ENGINE”)Malfunction is detected when.....Reference
page
CHAIN OF ECM-IMMU
[P1612]NATS MAL-
FUNCTION
P1612Communication impossible between ECM and BCM
In rare case, “CHAIN OF ECM-IMMU” might be stored
during key registration procedure, even if the system is
not malfunctioning.Refer to
BL-158,
"Diagnos-
tic Proce-
dure 1" .
DIFFERENCE OF KEY
[P1615]NATS MAL-
FUNCTION
P1615BCM can receive the key ID signal but the result of ID
verification between key ID and BCM is NG.Refer to
BL-159,
"Diagnos-
tic Proce-
dure 2" .
CHAIN OF IMMU-KEY
[P1614]NATS MAL-
FUNCTION
P1614BCM cannot receive the key ID signal.Refer to
BL-160,
"Diagnos-
tic Proce-
dure 3" .

NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-155
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Work FlowNIS002B3
1. LISTEN TO CUSTOMER COMPLAINT OR REQUEST
Get symptoms or listen to customer complaints or request.
NOTE:
In case of request for NVIS (NATS) system repair, the key ID re-registration might be necessary. Keep all the
ignition keys before work for the re-registration.
Key ID registration request>>Register ignition key by referring to CONSULT-III Operation Manual NATS-
IVIS/NVIS.
Request for malfunction repair.>>GO TO 2.
2. CONFIRM SELF DIAGNOSIS 1
Start CONSULT-III with ignition switch in ON position and confirm “SELF DIAG RESULT” with “ENGINE”.
Is DTC detected?
No malfunction>>GO TO 3.
If the codes detected are between the interval P1610 to P1615.>> Refer to BL-154, "
NVIS (NATS) SELF-
DIAGNOSTIC RESULTS ITEM CHART" .
If the codes detected are between the interval P1610 to P1615 and others.>> GO TO 4.
3. CHECK SECURITY INDICATOR FUNCTION
Check that security indicator for lighting up fulfill the two conditions below.

Security indicator lights off when ignition switch is ON position.

Security indicator blinks when ignition switch is in any position except ON.
Lighting up condition is normal.>>Inspection END.
Lighting up condition is malfunctioning.>>Perform security indicator Inspection. Refer to BL-163, "
Diagnostic
Procedure 5" .
4. TROUBLE DIAGNOSIS
Perform by priority the trouble diagnosis for the codes which are not included in the interval P1610 to P1615.
Is DTC detected?
No malfunction>>Inspection END.
If the codes detected are between the interval P1610 to P1615.>>BL-154, "
NVIS (NATS) SELF-DIAGNOS-
TIC RESULTS ITEM CHART".
ID DISCORD, IMM-ECM
[P1611]NATS MAL-
FUNCTION
P1611The result of ID verification between BCM and ECM is
NG. System initialization is required.Refer to
BL-161, "Diagnos-
tic Proce-
dure 4" .
LOCK MODE
[P1610]NATS MAL-
FUNCTION
P1610When the starting operation is carried out five or more
times consecutively under the following conditions, NVIS
(NATS) will shift the mode to one which prevents the
engine from being started.

Unregistered ignition key is used.

BCM or ECM’s malfunctioning.Refer to
BL-165,
"Diagnos-
tic Proce-
dure 6" .
DON'T ERASE BEFORE CHECK-
ING ENG DIAG—All engine trouble codes except NVIS (NATS) trouble
code has been detected in ECM.Refer to
BL-155,
"Work
Flow" . Detected items
[NVIS (NATS) program card screen
terms]P No. Code
(Self-diagnostic
result of
“ENGINE”)Malfunction is detected when.....Reference
page

BL-156
NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2006 November2007 350Z
Trouble DiagnosesNIS0003J
SYMPTOM MATRIX CHART 1
Self-diagnosis related item
SYMPTOMDisplayed “SELF-DIAG
RESULTS” on CON-
SULT-III screen.DIAGNOSTIC PROCE-
DURE
(Reference page)SYSTEM
(Malfunctioning part or
mode)REFERENCE PART NO.
OF ILLUSTRATION ON
SYSTEM DIAGRAM

Security indicator
lighting up*

Engine cannot be
startedCHAIN OF ECM-IMMU
[P1612]PROCEDURE 1
(BL-158
)In rare case, “CHAIN OF
ECM-IMMU” might be
stored during key regis-
tration procedure, even if
the system is not mal-
functioning.—
Open circuit in battery
voltage line of BCM cir-
cuitC1
Open circuit in ignition
line of BCM circuitC2
Open circuit in ground
line of BCM circuitC3
Open or short circuit
between BCM and ECM
communication lineC4
ECM B
BCM A
DIFFERENCE OF KEY
[P1615]PROCEDURE 2
(BL-159
)Unregistered key D
BCM A
CHAIN OF IMMU-KEY
[P1614]PROCEDURE 3
(BL-160
)Malfunction of key ID
chipE5
Communication line
between ANT/ AMP and
BCM:
Open circuit or short cir-
cuit of battery voltage
line or ground lineE1
E2
Open circuit in power
source line of ANT/ AMP
circuitE3
Open circuit in ground
line of ANT/ AMP circuitE4
NATS antenna amp. E6
BCM A
ID DISCORD, IMM-ECM
[P1611]PROCEDURE 4
(BL-161
)System initialization has
not yet been completed.F
ECM B

NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-157
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
*: When NVIS (NATS) detects trouble, the security indicator lights up while ignition key is in the “ON” position.
SYMPTOM MATRIX CHART 2
Non self-diagnosis related item
*: CONSULT-III self-diagnostic results display screen “no malfunction is detected”.
DIAGNOSTIC SYSTEM DIAGRAM

Security indicator
lighting up*

Engine cannot be
startedLOCK MODE
[P1610]PROCEDURE 6
(BL-165 )LOCK MODEWhen the starting opera-
tion is carried out five or
more times consecu-
tively under the follow-
ing conditions, NVIS
(NATS) will shift the
mode to one which pre-
vents the engine from
being started.

Unregistered ignition
key is used.

BCM or ECM’s mal-
functioning.
Security indicator light-
ing up*DON'T ERASE
BEFORE CHECKING
ENG DIAGWORK FLOW
(BL-155
)Engine trouble data and
NVIS (NATS) trouble
data have been detected
in ECM— SYMPTOMDisplayed “SELF-DIAG
RESULTS” on CON-
SULT-III screen.DIAGNOSTIC PROCE-
DURE
(Reference page)SYSTEM
(Malfunctioning part or
mode)REFERENCE PART NO.
OF ILLUSTRATION ON
SYSTEM DIAGRAM
SYMPTOMDIAGNOSTIC PROCEDURE
(Reference page)SYSTEM
(Malfunctioning part or mode)REFERENCE PART NO. OF
ILLUSTRATION ON SYSTEM
DIAGRAM
Security indicator does not light
up*.PROCEDURE 5
(BL-163
)Security indictor. —
Open circuit between Fuse and
BCM—
BCM A
PIIA1122E

BL-158
NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2006 November2007 350Z
Diagnostic Procedure 1NIS0003K
Self-diagnostic results:
“CHAIN OF ECM-IMMU” displayed on CONSULT-III screen
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-III, then perform the trouble diag-
nosis of malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to BCS-16, "
CAN Com-
munication Inspection Using CONSULT-III (Self-Diagnosis)" .
1. CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “CHAIN OF ECM-IMMU” displayed on CONSULT-III screen.
NOTE:
In rare case, “CHAIN OF ECM-IMMU” might be stored during key registration procedure, even if the system is
not malfunctioning.
Is CONSULT-III screen displayed as above?
Yes >> GO TO 2.
No >> GO TO BL-156, "
SYMPTOM MATRIX CHART 1" .
2. CHECK POWER SUPPLY CIRCUIT FOR BCM
1. Disconnect BCM connector.
2. Check voltage between BCM harness connector M91 terminal 42, 55 and ground with CONSULT-III or
tester.
OK or NG
OK >> GO TO 3.
NG >> Check the following.

40A fusible link (letter F , located in fuse and fusible
link box)

10A fuse [No.18, located in the fuse block (J/B)]

Harness for open or short between fusible link and
BCM. Ref. Part No. C1

Harness for open or short between fuse and BCM. Ref. Part No. C1
3. CHECK IGN SW. ON SIGNAL
1. Turn ignition switch ON.
2. Check voltage between BCM harness connector M90 terminal 38 and ground with CONSULT-III or tester.
OK or NG
OK >> GO TO 4.
NG >> Check the following.

10A fuse [No. 1, located in the fuse block (J/B)]

Harness for open or short between fuse and BCM.
Ref. part No. C2 42 (GY) - Ground : Battery voltage
55 (R) - Ground : Battery voltage
PIIA6374E
38 (W/L) - Ground : Battery voltage
PIIA6144E