2007 MERCEDES-BENZ S550 suspension

33 At a glance
Center console
Lower part
Item
Page
1
Favorite button
216
2
Rear head restraints retract
button
325
3
Program mode selector
switch for:

automatic transmission
shift program


suspension tuning of
Airmatic (only S 550) or
ABC*


engine control
374
4
Shortcut button for:

radio


CD/DVD
94
111
5
Back button
87
Item
Page
6
Hazard warning flasher
348
7
Seat operation via COMAND:

Lumbar support


Multicontour seat*


Drive-dynamic
multicontour seat*
236
237
237
240
8
Shortcut button for:

telephone*


navigation
115
148
9
COMAND controller
82
a
COMAND on/off switch
79
b
Volume adjustment
89
c
Mute function
89
d
Telephone keypad
117

374 Controls in detailAutomatic transmissionHill start assist system
On uphill grades with a gradient angle of
more than 5°, the hill start assist system
maintains the pressure in the brake sys-
tem for approximately 1 second after you
have released the brake pedal. Therefore,
you can start off smoothly without the
vehicle moving immediately after releasing
the brake pedal.The hill start assist system is inactive


when starting off on a level road or
downhill grades


with the automatic transmission in
neutral position N


with the electric parking brake set


if the ESP
® has switched off due to a
malfunction
Automatic shift program
The program mode selector switch is used
to adjust

shift program


suspension tuning of Airmatic*
(page 402) or ABC* (
page 404)


engine control
Program mode selector switchC Comfort For comfort driving
S Sport For standard driving
The selected program mode CorS ap-
pears in the tachometer display.
Warning!
G
The hill start assist system is not designed
to function as a parking brake and does not
prevent the vehicle from moving when
parked on an incline.
Always set the electric parking brake in
addition to shifting to park positionP.

375 Controls in detail
Automatic transmission
1Current program mode
Press program mode selector switch
repeatedly until the letter of the
desired program mode appears in the
tachometer display.Program modeC:


Engine, automatic transmission and
suspension tuning are comfortable.


The vehicle starts out in second
gear (both forward and reverse) for
gentler starts. This does not apply if
full throttle is applied or gear
range1 is selected.


Traction and driving stability are
improved on icy roads.


Upshifts occur earlier even when
you give more gas. The engine then
operates at lower rpms and the
wheels are less likely to spin.
Program modeS:


Engine, automatic transmission and
suspension tuning are more perfor-
mance oriented.


The vehicle starts out in first gear.


Upshifts occur later.
Steering wheel gearshift control
With drive positionD selected, you can
limit or extend the gear range.
The steering wheel gearshift buttons are
located on the back of the steering wheel
to the left and right.
!
Never change the program mode when the
automatic transmission is out of park positionP.
This could result in a change of driving character-
istics for which you may not be prepared.
i
The last selected program mode (CorS) is
switched on when the engine is restarted.
!
Allow engine to warm up under low load use.
Do not place full load on the engine until the op-
erating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road surfac-
es. This may cause serious damage to the driv-
etrain which is not covered by the
Mercedes-Benz Limited Warranty.

380 Controls in detailDriving systemsThe driving systems of your vehicle are de-
scribed on the following pages:

Cruise control and DISTRONIC Plus*,
with which the vehicle can maintain a
preset speed.


Distance warning function* (only avail-
able with DISTRONIC Plus*), which
warns of a stationary obstacle or slow-
er moving vehicle that you are closing
on to quickly.


Airmatic (S 550 only) and ABC* adjust
the vehicle suspension characteristics
automatically and control the vehicle
level.


Parktronic* and Park Assist*, which
serve as a parking assistant.


Dynamic Rear View Monitor* is an
electronic and visual parking aid.


Night View Assist* illuminates the road
with infrared light in addition to the nor-
mal headlamps.For information on the ABS, Adaptive
Brake, BAS, BAS Plus*, EBP, and ESP
® driv-
ing systems, see “Driving safety systems”
(
page 69).
Cruise control
Cruise control automatically maintains the
speed you set for your vehicle.
The use of cruise control is recommended
for driving at a constant speed for extend-
ed periods of time. You can set or resume
cruise control at any speed over 20 mph
(30 km/h).
The cruise control function is operated by
means of the cruise control lever.
Warning!
G
Cruise control is a convenience system de-
signed to assist the driver during vehicle op-
eration. The driver is and must always
remain responsible for the vehicle’s speed
and for safe brake operation.
Only use the cruise control if the road, traffic
and weather conditions make it advisable to
travel at a steady speed.

The use of cruise control can be danger-
ous on winding roads or in heavy traffic
because conditions do not allow safe
driving at a steady speed.


The use of cruise control can be danger-
ous on slippery roads. Rapid changes in
tire traction can result in wheel spin and
loss of control.


Deactivate cruise control when driving
in fog.
The “Resume” function should only be oper-
ated if the driver is fully aware of the previ-
ously set speed and wishes to resume this
particular preset speed.

401 Controls in detail
Driving systems
Airmatic (S 550 only)
Airmatic automatically selects the opti-
mum suspension tuning and ride height for
your vehicle.
Airmatic consists of two components:

Level control system


Adaptive Damping System (ADS)
The ADS automatically selects the opti-
mum damping for the respective driv-
ing conditions. At the same time the
suspension is set to either sporty or
regular.Vehicle level control with Airmatic
Your vehicle automatically adjusts its ride
height to:


reduce fuel consumption


increase vehicle stability
The vehicle chassis ride height is raised or
lowered according to the selected level
setting and to the vehicle speed:


With increasing speed, ride height is re-
duced by up to approximately 0.8 in
(20 mm).


With decreasing speed, the ride height
is again raised to the selected vehicle
level.The following vehicle level settings can be
selected when the vehicle is stationary:
Select the “Raised” level setting only when
required by current driving conditions.
Otherwise:


Fuel consumption may increase.


Handling may be impaired.
i
These height adjustments are so small that
you may not notice any change.
LevelNormal
For driving on normal roads.
The indicator lamp is off.
Raised
For driving on rough roads or
with snow chains. The indica-
tor lamp is on.

402 Controls in detailDriving systemsThe Airmatic button with the indicator
lamp is located on the control panel on the
right-hand side of the instrument cluster.
1Vehicle level control switch
2Indicator lamp

Start the engine.

Briefly press switch1 to change from
one level setting to the other.
The message:
Vehicle rising
appears in the multifunction display
when changing from normal level to
raised level.
The indicator lamp2 is then lit. The
display switches off when the vehicle is
raised.

Press switch1 again to lower the ve-
hicle. The indicator lamp2 is off.Suspension tuning
The Adaptive Damping System (ADS) auto-
matically tunes shock absorbers and
springs.
The program mode selector switch (S/C)
(
page 374) is used to adjust the suspen-
sion tuning:
In addition, suspension characteristics in
both driving programs (S/C) depend on:


your driving style


road surface conditions


the vehicle loading
Warning!
G
To help avoid personal injury, keep hands
and feet away from wheel housing area, and
stay away from under the vehicle when low-
ering the vehicle chassis.
i
The selected vehicle level setting remains
stored in memory even if the engine is turned off
and restarted except when you


exceed a speed of 75 mph (120 km/h)
or


maintain a speed of between 50 mph
(80 km/h) and 75 mph (120 km/h) for more
than 3 minutes
The vehicle then lowers to regular level.
Driving program
Suspension tuning
CComfort
Comfortable
(default setting)
SStandard
Standard
for dynamic driving

403 Controls in detail
Driving systems
Active Body Control (ABC)*
The ABC system automatically selects the
optimum suspension tuning and ride
height for your vehicle.
The ABC system consists of an active, hy-
draulically controlled suspension and
damping system.
Vehicle level control with ABC*
Your vehicle automatically adjusts its ride
height to:

reduce fuel consumption


increase vehicle stability
The vehicle chassis ride height is raised or
lowered according to the selected level
setting and to the vehicle speed:


With increasing speed, ride height is re-
duced by up to approximately 0.6 in
(15 mm).


With decreasing speed, the ride height
is again raised to the selected vehicle
level.The following vehicle level settings can be
selected when the vehicle is stationary:
Select the “Raised” level setting only when
required by current driving conditions.
Otherwise:


Fuel consumption may increase.


Handling may be impaired.
i
These height adjustments are so small that
you may not notice any change.
LevelNormal
For driving on normal roads.
The indicator lamp is off.
Raised
For driving on rough roads or
with snow chains. The indica-
tor lamp is on.
i
The selected vehicle level setting remains
stored in memory even if the engine is turned off
and restarted.
Warning!
G
To help avoid personal injury, keep hands
and feet away from wheel housing area, and
stay away from under the vehicle when low-
ering the vehicle chassis.

404 Controls in detailDriving systemsThe ABC level control switch with the indi-
cator lamp is located on the control panel
on the right-hand side of the instrument
cluster.
1Vehicle level control switch
2Indicator lampSelecting a higher level

Start the engine.
If indicator lamp2 is off:

Press switch1.
Indicator lamp2 comes on. The vehi-
cle is raised to a higher level.
Selecting a normal level

Start the engine.
If indicator lamp2 is on:

Press switch1.
Indicator lamp2 goes out. The vehicle
is adjusted to a normal level.Suspension tuning
The program mode selector switch (C/S)
(
page 374) is used to adjust the suspen-
sion tuning:
In addition, suspension characteristics in
both driving programs (S/C) depend on:


your driving style


road surface conditions


the vehicle loading
Driving program
Suspension tuning
CComfort
Comfortable
(default setting)
SStandard
Standard
for dynamic driving