2007 MERCEDES-BENZ S550 Auto Start

175 Control systems
COMAND navigation system (entering a destination)
Moving the map and selecting the des-
tination
Moving map: Slide qmr, omp or
wmx.

Adjusting map scale: rotate ymz.
Rotating clockwise enlarges the map,
rotating counterclockwise reduces it.

Selecting a destination: Press n.
If the crosshair is located off the edge
of the digital map, a route cannot be
calculated to this destination and you
will see the message “The destination is
located off the map.”.

Select “OK”.

Move the map and select a destination
again.
If the destination is within the limits of
the digital map, COMAND attempts to
attribute the destination to the map,
which can take approximately
2 seconds.If the destination can be attributed, you
will see the address of the destination.
If not, you will see the display “Destina-
tion from map”.

Starting route calculation:
Select “Start”, see also (
page 171).
Entering a stopoverEntering predefined destinations

Select “Navi”
“Destination”

“Stopover”.
If a stopover has already been entered,
you can change it.
Changing: Select “Change Stop-
over”.
You can now select a category.

Selecting a category:
Select category, e.g. “Gas station”.
COMAND first looks for destinations
within the immediate vicinity of the ve-
hicle and near the vehicle’s route. If
there are no destinations available
there, COMAND searches for destina-
tions in an area around the vehicle po-
sition.
If COMAND does not find any destina-
tions, you will see a message to this ef-
fect.
Select “OK”.
You can now select a different cat-
egory.
i
When route guidance is active, you can en-
ter a stopover. Stopovers can be predefined des-
tinations from the following predefined
categories:


“Mercedes-Benz Center”


“Hospital”


“Gas station”


“Parking lot”


“Restaurant”
However, you can also enter destinations other
than the predefined ones.
i
You can use the stopover function to influ-
ence the route guidance calculation to the main
destination. When you have reached your stop-
over, COMAND automatically calculates the
route to the main destination.


184 Control systemsCOMAND navigation system (Point of interest entry)Options only in POI lists
Displaying details of the selected
entry: Select “Options”
“Details”.
The detailed view appears.

Closing detailed view: Select “OK”.
Entering a POI from the map
Select “Guide” in the map view with the
menu system displayed (
page 148).
You will see POI symbols on the map,
depending on whether POIs are avail-
able and which map scale is set.
The scale at which the symbols are dis-
played on the map varies according to
the symbol.
You can set which symbols COMAND
should display (
page 151).The POI closest to the center of the
screen is automatically marked.
If there are no POIs available, the
“Back” menu item is automatically
highlighted and you cannot select oth-
er menu items.
1Highlighted POI
2Information about the highlighted POI

Selecting a POI: Select “Next” or “Pre-
vious”.
The next or the previous POI is marked.

Displaying details of the selection:
Select “Details”.

Starting route calculation:
Select “Start”, see also (
page 171).
A prompt appears asking whether the
POI should be used as the destination.

Select “Yes” or “No”.
If you select “Yes”, the route calcula-
tion begins. If you select “No”, you can
select a new POI.
i
If the crosshair is shown on the map, you
can enter POIs in the vicinity of the crosshair.
If the crosshair is not shown on the map, you can
enter POIs in the vicinity of the vehicle’s current
position.

188 Control systemsCOMAND navigation system (route guidance)Partially digitized areas If the destination is within a partially
digitized area
COMAND guides you through fully digitized
areas for as long as possible. Route guid-
ance is conducted in the usual manner, i.e.
with navigation announcements and route
guidance displays.
Before the vehicle reaches a partially digi-
tized area, COMAND notifies you of this
with the following announcements:


“Be prepared to enter an area where
turn by turn guidance cannot be provid-
ed.”


“In 700 feet you will enter an area
where turn by turn guidance cannot be
provided.”


“You are about to enter an area where
turn by turn guidance cannot be provid-
ed.”Route guidance within a partially digi-
tized area
If you start route guidance in this type of
area, you will hear the following announce-
ment: “You are currently in an area where
turn by turn guidance cannot be provided.”
Route guidance is provided by means of a
direction arrow showing the compass
heading to the destination. COMAND will
not generate automatic navigation an-
nouncements.
If you try to call up an announcement man-
ually, (
page 191) you will hear the an-
nouncement “You are currently in an area
where turn by turn guidance cannot be pro-
vided.”.
i
The digital map may contain areas that are
only partially digitized although they are within a
digitized region.Warning!
G
Due to incomplete digitization, the route
shown on the map may differ from the actual
road/traffic situation.
If you follow the route shown on the map, for
example, it is possible that you could drive
the wrong way down a one-way street or
that a street cannot be driven on.
When using route guidance in a partially dig-
itized area, you must therefore be sure to
observe all relevant traffic regulations and
the course of the road.
All relevant traffic regulations and the
course of the road always take priority over
the route shown on the map.
i
The indicated distance can be seen here by
way of example. In reality, it may be different.
i
When you call up the route info to this type
of destination, (
page 193) the following data
shown there may differ from the actual situation:


Distance to the destination


Estimated driving time to the destination


Estimated arrival time

191 Control systems
COMAND navigation system (route guidance)
Navigation announcements
Route guidance is already active.

Calling up a current announcement:
Select “Navi”
6.
or

Press P favorite button if the button
has been programmed with this func-
tion.

Canceling navigation message:
Briefly press F shortcut button dur-
ing an announcement.

Switching off navigation messages:
Press and hold F during an an-
nouncement until the announcement is
switched off.
You will see the message “The driving
instructions have been muted.” for a
short while.

Switching navigation announce-
ments back on manually:
Select “Navi”
6.

Adjusting volume of the messages:
adjust the volume during an automatic
announcement (
page 89).
or

Call up an announcement manually us-
ing “Navi”
6 and adjust the vol-
ume (
page 89).
Warning!
G
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.i
If Russian or Chinese is set as the system
language, the navigation announcements are in
English. You will find how to set the system lan-
guage on (
page 216).
Navigation announcements are muted during
telephone calls. You can, however, call up a cur-
rent announcement at any time. You can also
call up a current announcement at any time if
you have missed an announcement.
i
You will find the button programming on
(
page 216).
i
The announcements remain switched off
even if you start a new route guidance or if
COMAND is switched off/on with theo but-
ton.
If you switch COMAND off by removing the
SmartKey from the starter switch and then
switch the ignition back on after more than
3 minutes, the announcements are automatical-
ly switched back on.

200 Control systemsCOMAND navigation system (destination memory)Displaying your own address
Select “Navi”
“Destination”

“From Memory”.
The destination memory list appears ei-
ther with or without the input charac-
ters. Whether the input characters
appear depends on the number of en-
tries in the destination memory.

Press n.
Destination memory list without input
characters
In the destination memory list without in-
put characters, the “My Address” entry is
automatically highlighted.

Press n.
If your own address has already been
assigned, you will see the menu for
starting route guidance with your own
address data.

Exiting menu: Select “Back”.
Destination memory list with input char-
acters
1Input characters
In the destination memory list with input
characters 1, the input characters are au-
tomatically activated.

Slide qm repeatedly until the input
characters disappear.
The list entry “My Address” is automat-
ically highlighted as long as you have
not entered any characters using the
input characters.
If you have entered characters
from the list of input characters:
Rotate ymz or slide qm repeatedly
until the list entry “My Address” is
highlighted.

Press n.
If your own address has already been
assigned, you will see the menu for
starting route guidance with your own
address data.

Exiting menu: Select “Back”.

206 Control systemsCOMAND address book
Canceling search: Switch from the
smart speller to the list (
page 205).
The entry at the top of the list is auto-
matically highlighted.

Going back to main address book
display: If necessary, switch from the
list to the smart speller (
page 205)
and select “Back” in the smart speller.
Searching via the list

If necessary, switch from the smart
speller to the list (
page 205).

Rotate ymz or slide qmr until desired
entry is highlighted on the list.
Displaying a complete address book en-
try
Searching for the desired entry
Search for an address book entry
(page 204).
or

Select an address book entry in the
main address book menu
(page 202).

Press n.
The detailed view appears.
Illustration: detailed view for private data1To go back to the previous menu
2To switch between work and home
data ( symbol or )
3Selected data field
4Display of set data type – in example
display, home data is set ( symbol
and “Home” display)
5To call up optionsSwitching between private or business
data

Select symbol 2.
The display switches to private or busi-
ness data, depending on the previous
status.
i
The options available under “Options” menu
item 4 depend on which data field 3 is select-
ed. The following options may be available:


Displaying abbreviated content in full
(page 207)


Changing an address book entry
((page 207)


Changing the description of a telephone
number data field (
page 208)


Adding a telephone number data field
(page 208)


Calling a number saved in an entry
(page 209)


Starting route guidance to an entry
(page 209)


Options for voice entries (
page 210)


215 Control systems
COMAND system settings
Setting the time/date format
Select “Vehicle”
“System Settings”

“Time”
“Format”.
The format list appears. The dots R in
front of the list entries indicate the cur-
rent setting.

Changing format setting:
Select desired format.

Saving setting and exit the menu:
Slide omp.
Voice Control* settings
Switching help window on or off
Select “Vehicle”
“System Settings”

“Voice Control”.

Select “Help Window”.
You can switch the help window on or
off. A checkmark appears when the
help window is switched on.Individualization
Using individualization, you can fine-tune
Voice Control* to your own voice and thus
improve voice recognition. The ability of
the system to recognize the commands of
other users does not deteriorate as a re-
sult.
Individualization consists of two parts. You
train the system to recognize digits in the
first part and specific commands in the
second part.
Starting new individualization

Select “Vehicle”
“System Settings”

“Voice Control”
“Start new indi-
vidualization”.
A prompt appears asking whether you
would like further information.

Select “Yes” or “No”.
If you select “No”, the first part of indi-
vidualization begins.
If you select “Yes”, an information dis-
play will be shown with audio instruc-
tion.
Closing display: Select “OK”.
The first part of individualization be-
gins.
At the end of the first part, you will see
a prompt asking whether you want to
begin the second part.

Select “Yes” or “No”.
If you select “No”, individualization will
be canceled. The data from the first
part is saved automatically.
If you select “Yes”, the second part be-
gins.
Individualization is completed at the end of
the second part. You will see a message to
this effect. The data from the second part
is saved automatically.
i
It is only possible to start individualization
with the vehicle stationary. After starting the
session, the system will guide you through the in-
dividualization by means of acoustic instruc-
tions.

217 Control systems
COMAND system settings

Changing setting: Rotate ymz and
select desired function.

Saving setting and exit the menu:
Press n.
Bluetooth settings
General information about Bluetooth
Bluetooth technology is the standard for
short-range wireless data transmission of
up to approximately 10 meters. Bluetooth
can be used to exchange vCards or make
calls using a headset.
Activate or deactivate Bluetooth
Select “Vehicle”
“System Settings”

“Services”
“Deactivate Blue-
tooth”.
You have activated or deactivated Blue-
tooth. A checkmark appears when
Bluetooth is deactivated.Connecting Bluetooth devices
It is possible to establish a Bluetooth con-
nection between COMAND and the follow-
ing types of device:


Mobile phone (only for transferring
business cards)


Headset


Laptop / PDA
You can connect up to twelve devices to
COMAND but only one device can be ac-
tive at a time.
The connection process includes search-
ing for the device and its subsequent au-
thorization.Calling up the Bluetooth device list and
searching for devices

Calling up the list: Select “Vehicle”

“System Settings”
“Services”

“Search for Bluetooth devices”.
When you call up the list for the first
time after switching on COMAND, the
search for devices in the reception
range starts automatically. You will see
a display to this effect.
The device list appears after a short
while.
Canceling search:
Select “Cancel”.
The second time you call up the list, and
each time thereafter, the device list ap-
pears immediately if COMAND has not
been switched off and on again in the
meantime.

Starting search manually:
select “Update”.
i
To connect a Bluetooth device, the Blue-
tooth function must be activated in COMAND
and in the device concerned. The Bluetooth de-
vice must also be set to “visible” or “findable” in
order for COMAND to find and display it. For the
setting procedures, please see the operating in-
structions for the Bluetooth device.