2007 MERCEDES-BENZ S550 page

210 Control systemsCOMAND address bookDepending on which data is missing or
cannot be found on the digital map, you
must now either:

select a state (province)


select a county


or enter a town/city


or enter a street


or enter a house number

Selecting a state (province):
Select desired state (province) from
the list.

Selecting a county: Select desired
county from the list.

Entering a town: Proceed as de-
scribed for destination entry in the “En-
tering a town or city” section
(page 159).

Entering a street: Proceed as de-
scribed for destination entry in the “En-
tering a street” section (
page 161).

Entering a house number: Proceed
as described for destination entry in
the “Entering a house number” section
(page 166).
If all data is available and matches the dig-
ital map data, the navigation system starts
the route calculation.
Voice entries
Adding or changing a voice entry
Search for the address book entry with
or without a voice entry (
page 204).

Select “Options”
“Voice Name”

“Add” or “Change”.
Subsequent operation is controlled by
voice. Voice Control* guides you
through the dialogs.
i
If you have added data, COMAND saves your
additions. This means that you do not need to
re-enter this additional data later on.
The COMAND memory saves the additional data
in a special field, which cannot be displayed. The
data, which you have entered in the address
book initially in the display, remains unchanged.
i
For voice entries, your vehicle must be
equipped with Voice Control*. You can not add
voice entries for address book entry that come
from the phone book in the mobile phone.
i
You can add one voice entry per address
book entry.

211 Control systems
COMAND address book
Deleting a voice entry
Search for the address book entry with
a voice entry (
page 204).

Select “Options”
“Voice Name”

“Delete”.
A deletion prompt appears.

Select “Yes” or “No”.
COMAND deletes the voice entry de-
pending on your selection.
Listening to a voice entry

Search for the address book entry with
a voice entry (
page 204).

Select “Options”
“Voice Name”

“Read Aloud”.
You will hear the voice entry.Saving a phone book entry from mobile
phone in the COMAND address book
Saving a phone book entry from mobile
phone as new address book entry
Search for phone book entry in mobile
phone (
page 204).
or

Display details of a phone book entry in
the mobile phone (
page 206).

Select “Options”
“Save”
“New En-
try”.

Select a number category, e.g. “Work”.

Select a telephone category, e.g. “Mo-
bile”.

Select “Save”.
The input menu appears with the data
fields. The name and the telephone
number are entered automatically.
1Data field
2Input mark (cursor)
3Input characters

Proceed as described in the “Changing
a data field” paragraph in the “Creating
a new address book entry” section
(Seite 203).
i
The mobile phone must be inserted in the
cradle* and the COMAND have read out the mo-
bile phone book data. This can take several min-
utes, depending on how many entries each
phone book contains.

212 Control systemsCOMAND address bookSaving a phone book entry from the
mobile phone in an existing address
book entry
Search for a phone book entry in the
mobile phone (
page 204).
or

Display details of a phone book entry in
the mobile phone (
page 206).

Select “Options”
“Save”
“Add”.

Select a number category, e.g. “Home”.

Select a telephone category, e.g. “Land
Line”.

Select “Save”.
The search menu for address book en-
tries appears.

Search for desired entry.

After selecting an entry, press n.
COMAND saves the data if there are
fewer than four numbers assigned to
the selected entry in the selected num-
ber category. Otherwise, you will see a
prompt asking whether one of the ex-
isting numbers should be overwritten.

Select “Yes” or “No”.
If you select “Yes”, a selection list will
appear containing the four existing
numbers.

Select the number to be overwritten.
COMAND overwrites the selected num-
ber with the new data.
Importing data from external Bluetooth
devices
You can import vCards from external Blue-
tooth devices into the address book.
Please keep the following in mind:

Bluetooth is activated in COMAND
(page 217) and in the device con-
cerned.


The external device must be able to
send vCards by Bluetooth.


The external device is inside the vehi-
cle, switched on and authorized
(page 217).

Importing: Start data transfer on the
external device (see operating instruc-
tions of the device concerned).
If there is no address book entry with
the same first name and last name,
COMAND imports the data.
If there is already an address book en-
try with the same first name and last
name, a prompt will appear asking
whether the existing data should be
overwritten.

Select “Yes” or “No”.
The existing address book entry will be
overwritten or not, depending on your
selection.
i
The mobile phone must be inserted in the
cradle*.
i
There is a detailed description of how to
search for an address book entry in the “Search-
ing for an address book entry” section
(
page 204).

213 Control systems
COMAND system settings
COMAND system settings
Systems settings menu overviewDisplay settings
Switching the display on or off
Switching off: Select “Vehicle”

“Display OFF”.

Switching back on: Rotate ymz or
slideqmr.
Setting the display design

Select “Vehicle”
“System Settings”

“Display”.

Select “Day Mode” or “Night Mode” or
“Automatic”.
Time settings
Setting the time

Select “Vehicle”
“System Settings”

“Time”
“Time”.

Selecting hour or minute(s):
Slideomp.

Setting value: Rotate ymz or
slideqmr.

Saving setting: Press n.
i
The components and operating principles of
COMAND can be found on (
page 79).
Display
(page 213)
Time
(page 213)
Voice Control*
(page 215)
Language
(page 216)
Favorite
(page 216)
Services
(page 217)
Reset
(page 213)
Display settings
Time settings
Voice Control*
settings
Language
settings
Assign favorite
button
Bluetooth
settings
Reset COMAND to
factory settings
i
In the “Automatic” setting, COMAND ana-
lyzes the automatic vehicle light sensor and
switches between the display design automati-
cally.
i
The correct time must be set for the follow-
ing navigation system functions to operate cor-
rectly:


Route guidance on routes with time-depen-
dent traffic guidance


Calculation of estimated arrival time
i
The increment value for setting the minutes
depends on the situation. If GPS reception is
available, it is 30 minutes. If GPS reception is not
available, it is one minute.

218 Control systemsCOMAND system settingsThe device list can contain the following
devices:

All detected devices, whether autho-
rized or not.


All authorized devices, whether detect-
ed or not.
1Authorized and detected device – de-
vice and padlock symbol are the same
color
2Device which was not detected, but
which has been authorized in the past
– device and padlock symbol are differ-
ent colors (the device may be switched
off or not in the vehicle, for example)
3Newly detected device - not yet autho-
rized (no symbol)Displaying details of a Bluetooth device

Call up Bluetooth device list
(page 217).

Select desired device.

Select “Details”.
The detailed display for this device ap-
pears.

Closing detailed display: Slide qmr
or press n.Authorizing a Bluetooth device

Call up Bluetooth device list
(page 217).

Select unauthorized device.

Select “Authorize”.
The input menu for the passkey ap-
pears.
i
If the device list already contains twelve au-
thorized devices, you must revoke authorization
for one of the authorized devices. Then you must
switch this device off and then restart the
search. Any new devices for which you would like
to search will otherwise not appear in the list.
i
The passkey is any one to sixteen-digit num-
ber which you can set yourself. You must enter
the same number in COMAND and also in the de-
vice to be authorized.
i
On devices which do not have an input key-
pad (e.g. headsets), the passkey is predeter-
mined. In this case, it is not necessary to enter
the number on the device itself. You will usually
find the passkey in the operating instructions for
the device.

219 Control systems
COMAND system settings

Entering passkey into COMAND:
Select the digits one by one.

Deleting digits: Select ) and briefly
press n.

Canceling entry into COMAND:
select “Back”.

Confirming entry into COMAND:
Select?.

If necessary, enter the same passkey
into the Bluetooth device (see the op-
erating instructions for the device).
The device is authorized.De-authorizing a Bluetooth device

Call up Bluetooth device list
(page 217).

Select authorized device.

Select “De-authorize”.
A prompt appears asking whether you
really want to de-authorize this device.

Select “Yes” or “No”.
If you select “Yes”, the device will be
de-authorized.
Reset
Select “Vehicle”
“System Settings”

“Reset”.
A prompt appears asking whether you
really want to reset.

Select “Yes” or “No”.
If you select “Yes” another prompt will
appear asking whether you really want
to reset.

Select “Yes” or “No”.
If you select “Yes”, COMAND will be re-
set and restarted.
i
If you de-authorize a device which has been
authorized in the past and which is not detected
in the search, this device will no longer be dis-
played in the device list.
Devices which have been authorized in the past
but which are not detected in the search are ei-
ther not switched on or not in the vehicle.
i
You can reset COMAND back to its factory
settings.
In this case, all personal data (e.g. address book
entries, entries in the destination memory and
the list of last destinations of the navigation sys-
tem), among other things, is deleted.

220 Control systemsCOMAND vehicle menuIn this menu, you can program the follow-
ing vehicle functions:
Setting night security illumination
(Exterior Lighting Delayed Switch-off)
Use this function to set whether and how
long you would like the exterior lighting to
illuminate during darkness after exiting the
vehicle and all doors closed.
The exterior lighting automatically goes
out after the delayed switch-off time has
expired.
You can select:

“0 sec.”, the delayed switch-off feature
is deactivated


“15 sec.”, “30 sec.”, “45 sec.”, or
“60 sec.”, the delayed switch-off fea-
ture is activated

Select “Vehicle”.
The main area is active.

Selecting “Exterior Lighting Delayed
Switch-off” menu: Slide omp or
rotateymz.

Confirming selection: Press n.

Selecting length of time: Slide qmr
or rotate ymz.

Confirming selection: Press n.
or

Select “Vehicle”
“Vehicle”
“Exte-
rior Lighting Delayed Switch-off”.
A selection list appears.
The current setting is indicated by a
dotR.
Function
Page
Exterior Lighting Delayed
Switch-off
220
Locator Lighting
221
Exterior Mirror Convenience Set-
tings
222
Automatic Locking
223
Easy Entry/Exit Feature
224
Interior Ambient Light
225
Interior Lighting Delayed
Switch-off
226
Rear Window Sunshade
227
Trunk Opening-height Restriction
227
Tow-away Alarm
228
i
The components and operating principles of
COMAND can be found on (
page 79).
i
You can reactivate this function within
10 minutes by opening a door.

221 Control systems
COMAND vehicle menu

Selecting length of time: Slide qmr
or rotate ymz.

Confirming selection: Press n.
To activate night security illumination:

Select delayed switch-off period (see
above).

Turn the exterior lamp switch to
position* before turning off the en-
gine.
Locator lighting on/off
With the locator lighting feature activated
and the exterior lamp switch in position
*(
page 346), the following lamps will
switch on during darkness when the vehi-
cle is unlocked from the outside:


Parking lamps


Tail lamps


License plate lamps


Front fog lamps


Door entry lamps in the mirror


Side marker lamps
The locator lighting switches off when the
driver’s door is opened.If you do not open a door after unlocking
the vehicle with the SmartKey, the lamps
will switch off automatically after approxi-
mately 40 seconds.

Select “Vehicle”.
The main area is active.

Selecting “Locator Lighting” func-
tion: Slide omp or rotate ymz.

Confirming selection: Press n.

Switching locator lighting on or off:
Press n.
or
i
The components and operating principles of
COMAND can be found on (
page 79).