2007 MERCEDES-BENZ R320CDI instrument cluster

156 Controls in detail
Instrument cluster
For a full view illustration of the instrument
cluster, see “Instrument cluster”
(
page 26).
1To dim instrument cluster illumination
2Reset button
3To brighten instrument cluster
illuminationThe instrument cluster is activated when
you
open a door

switch on the ignition (page 39)

press reset button 2

switch on the exterior lamps
(
page 146)
You can change the instrument cluster
settings in the instrument cluster submenu
of the control system (
page 179).
Warning!G
No messages will be displayed if either the
instrument cluster or the multifunction
display is inoperative.
As a result, you will not be able to see infor-
mation about your driving conditions, such
as speed or outside temperature, warn-
ing/indicator lamps, malfunction/warning
messages or the failure of any systems.
Driving characteristics may be impaired.
If you must continue to drive, do so with
added caution. Contact an authorized
Mercedes-Benz Light Truck Center as soon
as possible.

157 Controls in detail
Instrument cluster
Adjusting instrument cluster
illumination
Use button 1 or 3 to adjust the illumina-
tion brightness for the instrument cluster.
To brighten illumination
Press and hold button 3 until the
desired level of illumination is reached.
To dim illumination
Press and hold button 1 until the
desired level of illumination is reached.
Resetting the trip odometer
Make sure you are viewing the trip odome-
ter display (
page 159).
If it is not displayed, press buttonè
orÿ on the multifunction steering
wheel (
page 160) repeatedly until
the trip odometer appears in the multi-
function display.
Press and hold reset button 2
(
page 156) until the trip odometer is
reset.
Tachometer
The red marking on the tachometer
(
page 26) denotes excessive engine
speed.
To help protect the engine, the fuel supply
is interrupted if the engine is operated
within the red marking.
iThe instrument cluster illumination is
dimmed or brightened automatically to suit
ambient light conditions.
The instrument cluster illumination will also be
adjusted automatically when you switch on the
vehicle’s exterior lamps.!Avoid driving at excessive engine speeds, as
it may result in serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.

158 Controls in detail
Instrument cluster
Outside temperature indicator
The outside temperature is indicated in the
multifunction display (
page 159).The temperature sensor is located in the
front bumper area. Due to its location, the
sensor can be affected by road or engine
heat during idling or slow driving. This
means that the accuracy of the displayed
temperature can only be verified by com-
parison to a thermometer placed next to
the sensor, not by comparison to external
displays (e.g. bank signs etc.).
When moving the vehicle into colder
ambient temperatures (e.g. when leaving
your garage), you will notice a delay before
the lower temperature is displayed.
A delay also occurs when ambient temper-
atures rise. This prevents inaccurate
temperature indications caused by heat
radiated from the engine during idling or
slow driving.
Warning!G
The outside temperature indicator is not de-
signed to serve as an ice-warning device and
is therefore unsuitable for that purpose.
Indicated temperatures just above the freez-
ing point do not guarantee that the road sur-
face is free of ice. The road may still be icy,
especially in wooded areas or on bridges.

165 Controls in detail
Control system
Menus, submenus and functions
Menu6Menu7Menu8Menu9MenuaMenub
DISTRONIC*Vehicle status
message memorySettingsDistance warning
function*Trip computerTelephone*
(page 271)(page 174)(page 176)(page 191)(page 191)(page 193)
Commands/submenus
Status and settingsCalling up
malfunction mes-
sages, warning mes-
sages, and system
status messages
stored in memoryResetting to factory
settingsDistance warning
function* on/offFuel consumption
statistics after startLoading phone book
Instrument cluster
submenuFuel consumption
statistics since the
last resetSearching for name
in phone book
Time/Date
submenuDistance to empty
Lighting submenu
Vehicle submenu
Comfort submenu*
iThe headings used in the menus table are
designed to facilitate navigation within the sys-
tem and are not necessarily identical to those shown in the control system displays. The first
function displayed in each menu will show you
which part of the system you are in.

176 Controls in detail
Control system
Settings menu
In the
Settings menu there are two
functions:

The function Reset to factory
settings?
, with which you can reset all
the settings to the original factory
settings.

A collection of submenus with which
you can make individual settings for
your vehicle.
Press buttonè orÿ repeatedly
until the
Settings menu appears in the
multifunction display.The following settings and submenus are
available in the
Settings menu:Resetting all settings
You can reset the functions of all
submenus to the factory settings.
Press the reset button in the
instrument cluster (
page 156) for
approximately 3 seconds.
The request to press the reset button
once more to confirm appears in the
multifunction display.
Press the reset button once more.
The functions of all the submenus will
reset to factory settings.
FunctionPage
Resetting all settings176
Submenus in the Settings menu177
Instrument cluster submenu179
Time/date submenu181
Lighting submenu183
Vehicle submenu186
Comfort submenu*189

178 Controls in detail
Control system
The table below shows what settings can
be changed within the various menus.
Detailed instructions on making individual
settings can be found on the following
pages.
INSTRUMENT CLUSTERTIME/DATELIGHTINGVEHICLECOMFORT*
(page 179)(page 181)(page 183)(page 186)(page 189)
Selecting speedometer display
modeSetting the time
(hour)Setting daytime running
lamp mode (USA only)Calling up the compassActivating
easy-entry/exit feature*
Selecting languageSetting the time
(minutes)Setting locator lightingCompass adjustmentSetting fold-in function
for exterior rear view
mirrors*
Selecting display (digital
speedometer or outside
temperature) for status indicatorSetting the date
(month)Setting night security
illuminationCompass calibration
Setting the date
(day)Setting interior lighting
delayed shut-offAudio search function
Setting the date
(year)Setting automatic
locking
Limiting opening height
of tailgate*

179 Controls in detail
Control system
Instrument cluster submenu
Access the
Instr. cluster submenu via
the
Settings menu. Use the Instr.
cluster
submenu to change the instru-
ment cluster display settings.
The following functions are available:Selecting speedometer display mode
Move the selection marker with
buttonæ orç to the
Instr.
cluster
submenu.
Press buttonj ork repeatedly
until the message
Display unit
Digital speedometer
appears in the
multifunction display.
The selection marker is on the current
setting.
Press buttonæ orç to set
speedometer unit to
km or miles.Selecting language
Move the selection marker with
buttonæ orç to the
Instr.
cluster
submenu.
Press buttonj ork repeatedly
until the message
Language appears in
the multifunction display.
The selection marker is on the current
setting.
Press buttonæ orç to select
the language to be used for the
multifunction display messages.
FunctionPage
Selecting speedometer display
mode179
Selecting language179
Selecting display (digital
speedometer or outside
temperature) for status indicator180

192 Controls in detail
Control system
Fuel consumption statistics from start
Press buttonÿ orè repeatedly
until the message
From start appears
in the multifunction display.
1Distance driven since start
2Time elapsed since start
3Average speed since start
4Average fuel consumption since startResetting fuel consumption statistics
Press buttonÿ orè repeatedly
until the message
From start appears
in the multifunction display.
Press and hold the reset button in the
instrument cluster (
page 156) until
the value is reset to
0.Fuel consumption statistics since last
reset
Press buttonÿ orè repeatedly
until the message
From start appears
in the multifunction display.
Press buttonj ork repeatedly
until the message
After reset appears
in the multifunction display.
1Distance driven since last reset
2Time elapsed since last reset
3Average speed since last reset
4Average fuel consumption since last
reset
iAll statistics stored since the last engine
start will be reset approximately 4 hours after
the SmartKey in the starter switch is turned to
position0 or removed from the starter switch.
Resetting will not occur if you turn the SmartKey
back to position1 or2 within this time period.