2007 MERCEDES-BENZ R320CDI remove seats

141 Controls in detail
Seats
Removing head restraints
Seat position for removal of head restraints
from second-row seats
1Head restraint
2Release button
To remove head restraint 1, pull head
restraint 1 to its uppermost position.
Press release button2 and pull out
head restraint 1.Installing head restraints
Insert head restraint 1 into openings
on the seat backrest.
Push head restraint 1 down until it
audibly engages.
Push release button2 and adjust
head restraint 1 to the desired
position (
page 139).Armrests
The second-row seat armrests can be
folded up, when loading for example, and
adjusted.
Folding up
Move the armrest into a vertical posi-
tion until it engages.
Adjusting
With the armrest folded up, disengage
the armrest by pushing it towards the
rear slightly.
Fold the armrest down to the lowest
and then to the desired position until it
engages.
To readjust the armrest to a higher
position, move armrest up to the
desired position until it engages.
iThe third-row seat head restraints are re-
moved in the same manner.
iOn the second-row seats, the guide bar with
the detent must be on the left.
iThe third-row seat head restraints are
installed in the same manner.
iTo readjust the armrest to a lower position,
you must first fold up the armrest again and re-
peat the steps above.

303 Controls in detail
Loading
Folding second-row seats
Move the seat to be folded to its rear-
most position (
page 138).
Remove the rear center console*, if so
equipped (
page 323).
Remove the head restraint from the
respective second-row seat
(
page 141).
1Seat backrest
2Seat cushion
3Release lever
Place the head restraint on the seat
cushion.
Relieve the load on seat backrest 1
and pull release lever 3 past the
resistance point in direction of arrow
as far as it will go.
Seat and seat backrest are unlocked.
Fold seat backrest 1 forward until it
fully rests on seat cushion 2 in a
horizontal position.
1Seat backrest
2Seat cushion
Push down on folded seat backrest 1
until seat cushion 2 engages in seat
base.
!When the second-row seats are folded
forward, the front seats may not be moved to the
rearmost position. Otherwise you could damage
the front and second-row seats.
iThe rear center console* can remain
installed, if installed in the most forward position
(
page 325). However, the cargo compartment
floor will then not be an even plane.
The storage compartment and the cupholders in
the rear center console* are only illuminated,
when the rear center console* is installed in the
most rearward position (position 0)
(
page 325).

306 Controls in detail
Loading
Cargo compartment cover blind*
The cargo compartment cover blind can be
installed behind the third-row seats or the
second-row seats.
Blind installed behind third-row seats
1Handle
2Mount
Rolling out blind
Pull blind on handle1 across the
cargo compartment.
Guide blind into mounts2 and
release.
Rolling up blind
Disengage blind and guide retraction
by its handle1.Removing blind
Blind installed behind second-row seats
1Release button
2Blind
Roll the blind up.
Push release button1.
Pull blind 2 to the left against the
spring pressure until the spring in the
blind audibly engages.
Remove the blind.
!With the cargo compartment cover blind
installed, do not pile luggage higher than the
lower edges of the rear side windows.
iThe cargo compartment cover blind has two
extensions which are connected to the cargo
compartment cover blind by cords.
The cargo compartment cover blind must be
extended for installation behind the second-row
seats (
page 306).

307 Controls in detail
Loading
Installing blind
For installation behind second-row
seats, install the blind extensions
(
page 307).
Remove the covers from the mounts in
side trim.
Press on cover at its lower edge as
indicated by arrow.
The mount cover’s upper edge flips
up.
Remove mount cover by pulling
its upper edge out of side trim in
direction of arrow.
Place left side of blind 2 (page 306)
in left mount.
Position right side of blind 2
(
page 306) over right mount.
Press release button1 (page 306)
and guide blind 2 (
page 306) into
mount.
Extending blind1Blind
2Extension
3Guidings
4Guide pins
Position extension 2 over blind 1.
Guide pins 4 must point directly at
guidings 3.
Turn extension2 and blind 1 in op-
posite directions as indicated by the ar-
rows.
Guide pins 4 must engage in
guidings3.
!For installation behind third-row seats,
the blind extensions must not be installed.
Otherwise, the blind could be damaged.
iTo avoid loss of the mount covers, keep
them in a safe place while not in use, e.g. the
glove box.
iThe cargo compartment cover blind has two
extensions which are connected to the cargo
compartment cover blind by cords.
The cargo compartment cover blind must be
extended for installation behind the second-row
seats.


318 Controls in detail
Useful features
Cup holder in front of second-row seats
A cupholder is located in front of the
second-row seats.
Opening cup holder
1Storage compartment coverOpen storage compartment
cover1(
page 314).
Press storage compartment cover 1
down in direction of arrow as far as it
will go.
1Storage compartment cover
2Cup holder
Pull out cup holder 2 in direction of
arrow as far as it will go.Closing cup holder
Make sure you have removed all
containers from the cup holder.
Push cup holder 2 in until it engages.
Close storage compartment cover.
Cupholders in rear center console*
Cupholders are located on the rear center
console* between the second-row seats.
1Cup holders
!Close the cup holder when not in use and
before folding the second-row seats.
iVehicles with rear center console*
(
page 323) are not equipped with cupholders
in front of the second-row seats.

320 Controls in detail
Useful features
Removing ashtray insert
Grip ashtray insert 2 on the sides and
pull it out upwards.
Reinstalling ashtray insert
Insert ashtray insert 2 and push down
until the ball catch engages.
Close ashtray cover plate 1.Rear seat ashtray (second row)
Opening the ashtray
1Ashtray cover
2Ashtray insert
Open ashtray cover 1 (page 312).
Press ashtray cover 1 down in
direction of arrow as far as it will go.Removing ashtray insert
Open ashtray cover 1.
Press ashtray cover 1 down in
direction of arrow as far as it will go.
1Ashtray cover
2Ashtray insert
Push on ashtray insert 2 and pull it
out upwards.
Reinstalling ashtray insert
Insert ashtray insert 2 into opening.
Push down ashtray insert 2 until it
engages.
Close ashtray cover 1.
Warning!G
Remove ashtray insert only with vehicle
standing still. Set the parking brake to
secure vehicle from movement. Set auto-
matic transmission toP. With the automatic
transmission set toP, turn off the engine.
iVehicles with rear center console*
(
page 323) are not equipped with an ashtray
in front of the second-row seats.
!Close the ashtray when not in use and be-
fore folding the second-row seats.

323 Controls in detail
Useful features
Power outlet in second-row footwell
Switch on the ignition (page 39).
Flip up cover and insert electrical plug
(cigarette lighter type).Power outlet in cargo compartment
Switch on the ignition (page 39).
Flip up cover and insert electrical plug
(cigarette lighter type).
Rear center console*
The rear center console is located between
the second-row seats.
The rear center console contains:

Storage compartment (page 314)

Cupholder (page 318)

DVD-player* (see separate COMAND
operating instructions)
iWhen fully expanding the cargo compart-
ment, the rear center console has to be removed
from the vehicle in order for the cargo compart-
ment floor to be an even plane (
page 302).

427 Practical hints
What to do if …
ProblemPossible cause/consequenceSuggested solution
telltale flashes and you addition-
ally hear an intermittent warning
chime with increasing intensity.The vehicle’s speed once exceeded
15 mph (25 km/h) and you and/or your
front passenger have forgotten to fasten your
seat belts.Fasten your seat belts.
The seat belt telltale goes out and the
warning chime stops sounding.
There are items placed on the front passen-
ger seat and therefore the system senses the
front passenger seat as being occupied.Remove the items from the front
passenger seat and put them in a safe
place.
The seat belt telltale goes out and the
warning chime stops sounding.
iAfter 60 seconds with an unfastened seat
belt on one of the front seats, the warning chime
stops sounding and the seat belt telltale illumi-
nates continuously. The seat belt telltale will only
go out if both the driver and front passenger’s
seat belt are fastened, or the vehicle is standing
still and a front door is opened.