2007 MERCEDES-BENZ ML350 seat

242 Controls in detailPower tilt/sliding sunroof*Warning!
G
When closing the tilt/sliding sunroof, make
sure that there is no danger of anyone being
harmed by the closing procedure.
If the tilt/sliding sunroof encounters an ob-
struction that blocks its path in a circum-
stance where you are closing the tilt/sliding
sunroof by moving the tilt/sliding sunroof
switch past the resistance point, or by
pressing and holding button‹ on the
SmartKey, by pressing and holding the lock
button (vehicles with KEYLESS-GO*) on the
door handle, the automatic reversal function
will not operate.
The opening/closing procedure of the
tilt/sliding sunroof can be immediately halt-
ed by releasing the switch or, if the switch
was moved past the resistance point and re-
leased, by moving the switch in any direc-
tion.
The tilt/sliding sunroof is made out of glass.
In the event of an accident, the glass may
shatter. This may result in an opening in the
roof.
In a vehicle rollover, occupants not wearing
their seat belts or not wearing them properly
may be thrown out of the opening. Such an
opening also presents a potential for injury
for occupants wearing their seat belts prop-
erly as entire body parts or portions of them
may protrude from the passenger compart-
ment.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock your vehicle. Do not leave children un-
attended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment can cause an accident
and/or serious personal injury.!
To avoid damaging the seals, do not trans-
port any objects with sharp edges which can
stick out of the tilt/sliding sunroof.Do not open the tilt/sliding sunroof if there is
snow or ice on the roof, as this could result in
malfunctions.
The tilt/sliding sunroof can be opened or closed
manually should an electrical malfunction occur
(
page 478).
i
When the tilt/sliding sunroof is open, reso-
nance noises may result in addition to the usual
wind noises. They are caused by minimal pres-
sure changes in the passenger compartment. To
reduce or eliminate these noises, change the po-
sition of the tilt/sliding sunroof or open a side
window slightly.
i
You can also open or close the tilt/sliding
sunroof using the SmartKey or the
KEYLESS-GO* function, see “Summer opening
feature” (
page 239) and see “Convenience
closing feature” (
page 239).
i
Depending on the current position, the
tilt/sliding sunroof may also open or close when
the air recirculation button: on the control
panel of the climate control (
page 208) or
automatic climate control* (
page 222) is
pressed and held.

282 Controls in detailLoadingLoad distributionThe gross vehicle weight which is the
weight of the vehicle including fuel, tools,
spare wheel, installed accessories, pas-
sengers and luggage/cargo must never
exceed the load limit and Gross Vehicle
Weight Rating (GVWR) for your vehicle as
specified on the placard located on the
driver’s door B-pillar (
page 530). In addi-
tion, the load must be distributed in such a
way so that the weight on each axle never
exceeds the Gross Axle Weight Rating
(GAWR) for the front and rear axle. The
GVWR and GAWR for your vehicle are indi-cated on the certification label which can
be found on the driver’s door B-pillar
(
page 530).
For more information, see “Tire and Load-
ing Information” (
page 369).
The handling characteristics of a fully load-
ed vehicle depend greatly on the load dis-
tribution. It is therefore recommended to
load the vehicle according to the illustra-
tions shown, with the heaviest items being
placed towards the front of the vehicle.
Please pay attention to and comply with
the following instructions when loading the
vehicle and transporting cargo:


Always place items being carried
against front or rear seat backrests,
and fasten them as securely as possi-
ble.


The heaviest portion of the cargo
should always be kept as low as possi-
ble against front or rear seat backrests.For additional safety when transporting
cargo while the rear seats are unoccupied,
fasten the outer seat belts crosswise into
the opposite side buckles.
i
The cargo compartment is the preferred
place to carry objects. The expanded cargo com-
partment (
page 284) should only be used for
items which do not fit in the cargo compartment
alone.

283 Controls in detail
Loading
Cargo tie-down rings
Your vehicle is equipped with six cargo
tie-down rings.
Carefully secure cargo by applying even
load on all rings with rope of sufficient
strength to hold down the cargo.Cargo compartment
Four cargo tie-down rings are located in
the cargo compartment.
1Cargo tie-down ringBehind front seats
Two cargo tie-down rings are located in the
footwell behind the driver’s and passenger
seat.
1Cargo tie-down ringi
While the partition net* (
page 287) will
help protect you from smaller objects, it cannot
prevent the movement of large, heavier objects
into the passenger compartment in an accident,
during hard braking or sudden maneuvers. Such
items must be properly secured using the cargo
tie-down rings in the cargo compartment floor.

284 Controls in detailLoadingHooks
Four hooks are located on the rear com-
partment trim panels, two on each side.
1Hook
Use the hooks to secure light weight items
only. The maximum permissible weight per
hook is 9 lbs (4 kg).
Expanding cargo compartment
You can separately fold the left and right
rear seat backrests to expand the cargo
compartment.
Folding the rear seat backrest forwardWarning!
G
When expanding the cargo compartment,
always fully fold the corresponding seats
and, if so equipped, always use the partition
net* (
page 287) when transporting cargo.
Unless you are transporting cargo, the back-
rests must remain properly locked in the up-
right position.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle, and can cause
injury to vehicle occupants unless the items
are securely fastened in the vehicle.
Always use the cargo tie down rings
(
page 283).
Warning!
G
Never drive the vehicle with the tailgate
open. Deadly carbon monoxide (CO) gases
may enter vehicle interior resulting in un-
consciousness and death.!
Always release the seat cushion and fold it
up before folding the seat backrest forward. The
covering on the seat backrest may otherwise be
damaged.
When the seat backrest are folded forward, the
front seats may not be moved to the rearmost
position. Otherwise you could damage the front
and second-row seats.

285 Controls in detail
Loading
1Release handle
2Seat cushion
Pull release handle1.

Fold seat cushion2 forward.3Release handle
4Seat backrest

Make sure the rear seat head restraints
are in the lowermost position
(page 128).

Pull release handle3.A red indicator5 will be visible and the
seat backrest4 is released.
5Indicator

Fold seat backrest4 forward.

286 Controls in detailLoadingReturning the rear seat backrest to
original position
1Seat backrest
2Seat cushion
Fold seat backrest1 rearward until it
engages.
The red indicator5 (
page 285)
should no longer be visible.

Fold seat cushion2 rearward until it
locks into position.

Check for secure locking by pushing
and pulling on the seat backrest.
Cargo compartment cover blind
The cargo compartment cover blind can be
installed behind the rear seats.1Handle
2Mount
Rolling out blind

Pull blind on handle1 across the car-
go compartment.

Guide blind into mounts2 and re-
lease.
Rolling up blind

Disengage blind and guide retraction
by its handle1.
Warning!
G
If a red indicator is visible with the backrest
up, then the backrest is not properly locked
into position.
Always lock backrest in its upright position
when the rear seats are occupied, or the ex-
tended cargo compartment is not in use.
Check for secure locking by pushing and
pulling on the backrest.!
With the cargo compartment cover blind in-
stalled, do not pile luggage higher than the lower
edges of the rear side windows.

287 Controls in detail
Loading
Removing blind
1Release button
2Blind
Roll the blind up (
page 286).

Push release button1.

Pull blind2 to the left against the
spring pressure until the spring in the
cover audibly engages.

Remove the blind.
Installing blind

Place left side of blind2 in left mount.

Position right side of blind2 over right
mount.

Press release button1 and guide
cover2 into mount.

Make sure the cargo compartment
cover blind is securely fastened.
Partition net*
i
Before removing cargo compartment cover
blind behind the rear seats, fold the left or right
rear seat forward. Afterwards, return the left or
right rear seat into its original position.
i
Before installing cargo compartment cover
blind behind the front seats, fold the rear seats
forward.
Warning!
G
Make sure the partition net is properly en-
gaged at top and bottom position and the
tightening belts are securely fastened.
Never use a damaged partition net.
To help avoid personal injury from smaller
objects being thrown around in the occu-
pant compartment during a collision or sud-
den maneuver, always use partition net
when transporting cargo.
The partition net cannot prevent the move-
ment of large, heavier objects into the pas-
senger compartment in an accident. Such
items must be properly secured using the
cargo tie-down rings (
page 283) in the
cargo compartment floor.
Passenger use of seats behind installed par-
tition net is restricted because of the foot-
well being taken up by the net.

288 Controls in detailLoadingUse of the partition net is a particularly im-
portant safety factor when the vehicle is
loaded higher than the top of the seat
backrests with smaller objects. For your
safety, always use the partition net when
transporting cargo.
The partition net can be installed in two
locations:
1Holder in B-pillar
2Holder in C-pillar


Without the cargo compartment ex-
panded (
page 284), use holders
above C-pillars2 and the cargo
tie-down rings in the cargo compart-
ment (
page 283).


With the cargo compartment expanded
(page 284), use holders above
B-pillars1 and the cargo tie-down
rings behind the front seats
(page 283).

Open the zipper on the partition net
package.

Roll out the partition net.

Unfold the partition net.
The partition net bars must audibly
engage.Installing the partition net
Partition net bar hung up behind the C-pillar1Holder
2Partition net bar
Hang partition net bar2 on holder1
as indicated by the arrow.

Push partition net bar2 forward into
holder1 in direction of arrow.