2007 MERCEDES-BENZ GL450 ignition

197 Controls in detail
Automatic transmission
If you want the gear position to remain in
neutral positionN, e.g. when taking the
vehicle through an automatic conveyor
type car wash, observe the following
instructions.Vehicles with SmartKey:
With the vehicle at a standstill and the
ignition switched on shift the automatic
transmission to neutral positionN.
If engaged, release the parking brake
(
page 60).
Switch off the ignition and leave the
SmartKey in the starter switch.
Vehicles with KEYLESS-GO*:
With the vehicle at a standstill, depress
the brake pedal and keep it pressed.
With the ignition switched on shift the
automatic transmission to park
positionP.
Release the brake pedal.
Remove the KEYLESS-GO* start/stop
button from the starter switch
(
page 43).
Insert the SmartKey with
KEYLESS-GO* into the starter switch.
Switch on the ignition.
Depress the brake pedal.
Shift the automatic transmission to
neutral positionN.
Release the brake pedal.
If engaged, release the parking brake
(
page 60).
Switch off the ignition and leave the
SmartKey with KEYLESS-GO* in the
starter switch.
Warning!G
When leaving the SmartKey or SmartKey
with KEYLESS-GO* in the starter switch, do
not leave children unattended in the vehicle.
It is possible for children to switch on the
ignition which could result in unsupervised
use of vehicle equipment.
A child’s unsupervised access to a vehicle
could result in an accident and/or serious
personal injury.
!Coasting the vehicle, or driving for any other
reason in neutral positionN can result in
transmission damage that is not covered by the
Mercedes-Benz Limited Warranty.

203 Controls in detail
Transfer case
Transfer case
LOW RANGE mode*
The LOW RANGE mode is available on vehi-
cles with enhanced off-road package*.
In the following situations you should
switch to LOW RANGE mode:

during off-road driving (page 357)

when crossing water (page 362)

when towing up or down on steep
gradients
With the LOW RANGE selected, the
engine’s power delivery and the shifting
behavior of the automatic transmission are
adjusted. Furthermore, the ABS, ESP
® and
4-ETS functions especially adapted to
off-road travel are activated.
For information on driving safety systems
during LOW RANGE mode, see “Driving
safety systems” (
page 103).
For more information on Off-road driving,
see “Off-road driving” (
page 357).Gear Ranges
There are two possible settings.
!Operational or performance test must only
be conducted on a two-axle dynanometer. If
such tests are necessary, contact an authorized
Mercedes-Benz Light Truck Center. You could
otherwise seriously damage the brake system or
the transfer case which is not covered by the
Mercedes-Benz Limited Warranty.
!Because the ESP® operates automatically,
the engine and ignition must be shut off
(SmartKey in starter switch position0 or1 or
KEYLESS-GO* start/stop button in
position0or1) when testing the parking brake
on a brake test dynamometer and such testing
should be no longer than 10 seconds.
Active braking action through the ESP
® may
otherwise seriously damage the brake system
which is not covered by the Mercedes-Benz
Limited Warranty.
iThe vehicle is equipped with full-time
four-wheel drive. Both the front and rear axles
are powered at all times when the vehicle is
being operated.
HIGH
RANGERoad position for all normal
driving situations.
(LOW RANGE mode off)
LOW
RANGEOff-road position for traveling
on rough terrain.
(LOW RANGE mode on)
Also use the off-road position
when driving on-road on steep
gradients, especially when
towing a trailer.
LOW RANGE acts by raising
the engine’s gear ratio. The ve-
hicle travels at roughly third
the speed compared to when
in the HIGH RANGE position,
leading to an increase in the
engine’s drive power.

204 Controls in detail
Transfer case
Switching LOW RANGE mode
The switch is located on the upper part of
the center console.
1LOW RANGE switch
2Indicator lamp
3LOW RANGE displaySwitching LOW RANGE mode on
(switching from HIGH RANGE to LOW
RANGE)
Press LOW RANGE switch1.
Indicator lamp2 flashes.
If the system senses that all conditions
are met, it will switch to LOW RANGE
mode. A chime sounds and the LOW
RANGE display3 appears in the multi-
function display.
The indicator lamp2 on the
LOW RANGE switch comes on continu-
ously, indicating that the LOW RANGE
mode has been activated.
Warning!G
Always wait until the procedure of shifting
from HIGH RANGE to LOW RANGE – and
from LOW RANGE to HIGH RANGE – has
been entirely completed. During this proce-
dure do not:

switch off the engine

shift the automatic transmission into
another gear
If you do not wait until the shifting proce-
dure has been entirely completed then it
might not be correctly performed. The trans-
fer case might be in neutral, thus interrupt-
ing the transfer of power between the
engine and the drive axle.
The vehicle is then freely movable, even if a
gear has been selected, and could uninten-
tionally be set into motion – particularly on
up – or downhill grades. This could lead to
an accident and cause injury to yourself and
others.
Please observe related messages appearing
in the multifunction display (
page 493).
!The shift procedure can only be performed
when the following conditions are met:

The engine is running (page 41).

The automatic transmission is in positionN
(
page 193).

The vehicle speed does not exceed 25 mph
(40 km/h).
iThere is no reset to HIGH after the ignition
has been switched off.

205 Controls in detail
Transfer case
Switching LOW RANGE mode off
(switching from LOW RANGE to HIGH
RANGE)
Press LOW RANGE switch1
(
page 204).
Indicator lamp2 flashes.
If the system senses that all conditions
are met, it will switch to back to
HIGH RANGE mode. A chime sounds
and the LOW RANGE display3 ap-
pears in the multifunction display.
The indicator lamp2 on the
LOW RANGE switch goes out, indicat-
ing that the LOW RANGE mode has
been deactivated.
For messages in the multifunction display,
see “Practical hints” section (
page 493).
iYou can cancel the procedure by pressing
the LOW RANGE switch again while the indicator
lamp is flashing.
!The shift procedure can only be performed
when the following conditions are met:

The engine is running (page 41).

The automatic transmission is in positionN
(
page 193).

The vehicle speed does not exceed 43 mph
(70 km/h).
iThere is no reset to LOW after the ignition
has been switched off.
iYou can cancel the procedure by pressing
the LOW RANGE switch again while the indicator
lamp is flashing.

209 Controls in detail
Differential locks*
Start the engine (page 42).
To select the required locking mode,
rotate adjustment ring2 to the
desired position3 or4
(
page 207).
The indicator lamp on the adjustment
ring1 at the respective symbol
comes on.
Example
5Center differential is completely locked
!If the differential locks have been manually
engaged, the tires will scuff on the road surface
when cornering because the differences be-
tween the individual wheel rotation speeds will
not be compensated for.
iThe differential locks are reset to AUTO
mode after the ignition has been switched off for
longer than 10 seconds.

210 Controls in detail
Good visibility
For information on windshield wipers, see
“Windshield wipers” (
page 63).
Headlamp cleaning system*
The headlamp cleaning button is located
on the left side of the dashboard.
1Headlamp cleaning button
Switch on the ignition (page 42).
Press button1.
The headlamps are cleaned with a
high-pressure water jet.
For information on filling up the washer
reservoir, see “Windshield/rear window
washer system and headlamp cleaning
system*” (
page 384).
Rear view mirrors
For more information on setting the rear
view mirrors, see “Mirrors” (
page 52).
Interior rear view mirror, antiglare
position
1Lever
Tilt the mirror to the antiglare position
by moving lever1 towards the wind-
shield.
The interior rear view mirror is dimmed.
iThe headlamps will automatically be
cleaned when you have

switched on the headlamps
and

operated the windshield wipers with wind-
shield washer fluid fifteen times
When you switch off the ignition, the counter
resets.

211 Controls in detail
Good visibility
Auto-dimming rear view mirrors*
The reflection brightness of the exterior
rear view mirror on the driver’s side and
the interior rear view mirror will respond
automatically to glare when

the ignition is switched on
and

incoming light from headlamps falls on
the sensor in the interior rear view
mirror
The rear view mirror will not react if

the automatic transmission is set to
positionR

the interior lighting is turned onPower folding exterior rear view
mirrors*
Folding the exterior rear view mirrors
in and out automatically
When the corresponding function in the
control system is activated (
page 185):

The exterior rear view mirrors automat-
ically fold in as soon as the vehicle is
locked from the outside.

The exterior rear view mirrors automat-
ically fold out as soon as the vehicle is
unlocked and the driver’s or front pas-
senger door are subsequently opened.
Warning!G
The auto-dimming function does not react if
incoming light is not aimed directly at sen-
sors in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver’s side do not
react, for example, when transporting cargo
which covers the rear window.
Light hitting the mirror(s) at certain angles
(incident light) could blind you. As a result,
you may not be able to observe traffic con-
ditions and could cause an accident.
Warning!G
Exercise care when using the passen-
ger-side exterior rear view mirror. The mirror
surface is convex (outwardly curved surface
for a wider field of view). Objects in mirror
are closer than they appear. Check your
interior rear view mirror or glance over your
shoulder before changing lanes.
!Before you drive the vehicle through an
automatic car wash, fold the exterior rear view
mirrors in. Otherwise they may get damaged.

212 Controls in detail
Good visibility
Synchronizing exterior rear view
mirrors
The power folding rear view mirrors may
have to be synchronized after the vehicle
battery has been disconnected or dis-
charged. If the exterior rear view mirrors
do not fold properly upon locking or un-
locking the vehicle although the corre-
sponding function in the control system is
activated (
page 185), do the following:
Fold each exterior rear view mirror in
completely (
page 212).
Fold each exterior rear view mirror out
completely (
page 212).
When the exterior rear view mirrors fold
properly upon locking the vehicle, the exte-
rior mirrors are synchronized. Otherwise
repeat the above steps.Folding the exterior rear view mirrors
in and out manually
The button is located on the door control
panel.
1Button for folding exterior rear view
mirrors in and out
Switch on the ignition (page 42).Folding in
Briefly press button1.
Both exterior rear view mirrors fold in.
Folding out
Briefly press button1 again.
Both exterior rear view mirrors fold out.
iThe exterior rear view mirrors can vibrate if
they are not folded out completely.
iIf you are driving at more than approximately
30 mph (47 km/h), you will not be able to fold
the exterior mirrors in.
!If an exterior rear view mirror housing is
forcibly pushed forward (hit from the rear) or
forcibly pushed rearward (hit from the front)
press button1 to fold mirrors in, then press
button1 again to fold mirrors out. Do not force
mirrors by hand as this may damage the adjust-
ment mechanism.
The mirror housing is then properly positioned
and you can adjust the mirror in the usual
manner.
Please make sure both rear view mirrors are
folded out before driving off.