2007 MERCEDES-BENZ G55AMG suspension

258 Operation
Driving instructions

Comply with the warnings
(
page 253) and rules for off-road
driving (
page 253).

Switch off the exterior lamps as well as
the climate control.

Select gear range2 or1 on the auto-
matic transmission (
page 167).

Enter and leave the water only at a
shallow spot, driving at walking speed.

Drive through the water slowly and at a
constant speed.

Do not stop vehicle while immersed in
water, and do not shut off the engine.
There is a very high level of driving
resistance in water. The surface is
slippery and may not be firm, making
pulling away in water difficult and
dangerous.

Make sure that only small bow waves
are formed when driving the vehicle
through water.

Clean mud off the tire tread after
driving through water.

To dry the brakes, apply pressure to the
brake pedal several times after leaving
the water.Crossing obstacles
!Never accelerate before driving into the
water. The bow wave could force water into the
engine and auxiliary equipment, thus damaging
them.
!Do not open any of the vehicle’s doors while
driving through water. Water could otherwise en-
ter the vehicle interior and damage the vehicle’s
electronics, as well as the interior equipment.
!Obstacles can damage the vehicle
underbody or suspension components. If possi-
ble, use the assistance of a second person out-
side the vehicle to scout the path you intend to
take and check for adequate ground clearance
when you cross obstacles with your vehicle. The
person assisting you outside the vehicle should
always be a safe distance away from the vehicle
and positioned so that he or she cannot get hurt
in case of any unexpected vehicle movement.
After off-road driving or crossing obstacles,
inspect vehicle for any damage, especially
vehicle underbody and suspension components.
Failure to do so can adversely affect the vehi-
cle’s future performance, including increased
chance of an accident.

260 Operation
Driving instructions

Check the vehicle clearance before
driving in ruts.

Comply with the warnings
(
page 253) and rules for off-road
driving (
page 253).

Select gear range1 on the automatic
transmission (
page 167).

Drive slowly next to the ruts rather than
through them if at all possible.

If the ruts are too deep to drive in, drive
with one side of the vehicle on the
grassy center strip if the route permits.Returning from off-road drivingOff-road driving increases strain on the
vehicle.
We recommend that you inspect the vehi-
cle for possible damage after each off-road
trip. Recognizing any damage and a subse-
quent timely repair reduces the chance of
a possible breakdown or accident later on.
Proceed as follows:

Switch the transfer case in position
HIGH (
page 170).

Switch differential locks off
(
page 176).

Clean all exterior lamps and check
them for possible damage.

Clean the front and rear license plate.

Remove excessive dirt from tires,
wheels, wheel housings, and under-
body.
For instance, after driving in mud, clean
the radiator, chassis, engine, brakes,
and wheels from extreme dirt using a
strong jet of water.
After off-road driving or crossing obstacles,
inspect vehicle for any damage, especially
vehicle underbody and suspension components.
Failure to do so can adversely affect the vehi-
cle’s future performance, including increased
chance of an accident.
Warning!G
Never drive on pavement with activated
differential locks. Engaged front axle differ-
ential locks limits ability to move around
curves.
If you feel a sudden significant vibration or
ride disturbance, or you suspect that possi-
ble damage to your vehicle has occurred,
you should turn on the hazard warning flash-
ers, carefully slow down, and drive with cau-
tion to an area which is a safe distance from
the roadway.
Inspect the tires and under the vehicle for
possible damage. If the vehicle or tires
appear unsafe, have it towed to the nearest
Mercedes-Benz Light Truck Center or tire
dealer for repairs.
Damage to the vehicle may influence driving
comfort and poses the risk of accident to
you and other drivers.

277 Operation
Tires and wheels
Tires and wheels
Contact an authorized Mercedes-Benz
Light Truck Center for information on test-
ed and recommended rims and tires for
summer and winter operation. They can
also offer advice concerning tire service
and purchase.Important guidelines

Only use sets of tires and rims of the
same type and make.

Tires must be of the correct size for the
rim.

Break in new tires for approximately
60 miles (100 km) at moderate
speeds.

Regularly check the tires and rims for
damage. Dented or bent rims can
cause tire inflation pressure loss and
damage to the tire beads.

If vehicle is heavily loaded, check tire
inflation pressure and correct as
required.

Do not allow your tires to wear down
too far. Adhesion properties on wet
roads are sharply reduced at tread
depths of less than
1/8in (3 mm).

When replacing individual tires, you
should mount new tires on the front
wheels first (on vehicles with
same-sized wheels all around).
Warning!G
Replace rims or tires with the same designa-
tion, manufacturer and type as shown on the
original part. See an authorized
Mercedes-Benz Light Truck Center for fur-
ther information. If incorrectly sized rims
and tires are mounted:

The wheel brakes or suspension
components can be damaged.

The operating clearance of the wheels
and the tires may no longer be correct.
Warning!G
Worn, old tires can cause accidents. If the
tire tread is badly worn, or if the tires have
sustained damage, replace them.
When replacing rims, only use genuine
Mercedes-Benz wheel bolts specified for the
particular rim type. Failure to do so can
result in the bolts loosening and possibly an
accident.
Retreaded tires are not tested or recom-
mended by Mercedes-Benz, since previous
damage cannot always be recognized on
retreads. The operating safety of the vehicle
cannot be assured when such tires are used.

401 Practical hints
Towing the vehicle
Towing the vehicle
Mercedes-Benz recommends that the
vehicle be transported with all wheels off
the ground using flatbed or appropriate
wheel lift/dolly equipment. This method is
preferable to other types of towing.When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground only so far as necessary to have
the vehicle moved to a safe location where
the recommended towing methods can be
employed.
!Use flatbed or wheel lift/dolly equipment,
with SmartKey in starter switch turned to
position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Use the towing eyes.
Switch off the ESP
® (page 94), the tow-away
alarm (
page 98) and the automatic central
locking (
page 155).
!Do not tow-start the vehicle.
!When towing the vehicle with all wheels on
the ground, the gear selector lever must be in
neutral positionN and the SmartKey must be in
starter switch position2.
When towing the vehicle with all wheels on the
ground, the vehicle may be towed only for
distances up to 30 miles (50 km) and at a speed
not to exceed 30 mph (50 km/h).
If the vehicle is towed with one axle raised
(observe instructions regarding flexible drive
shaft and propeller shafts), the engine must be
shut off and the SmartKey must be in starter
switch position1. Otherwise, the 4-ETS may
become engaged which may cause loss of
towing control.
Warning!G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run

there is a malfunction in the brake sys-
tem

there is a malfunction in the power
supply or in the vehicle’s electrical
system
This is necessary to adequately control the
towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make sure the SmartKey is in
starter switch position2.
If the SmartKey is left in the starter switch
position0 for an extended period of time, it
can no longer be turned in the switch. In this
case, the steering is locked. To unlock,
remove SmartKey from starter switch and
reinsert.

402 Practical hints
Towing the vehicle
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle. Adapt your driving accordingly.
!Towing of the vehicle should only be done
using the towing eye. Never attach tow cable,
tow rope or tow rod to vehicle chassis, frame or
suspension parts.
iWhen towing the vehicle with all wheels on
the ground, note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, the
vehicle doors lock if a wheel is turning at vehicle
speeds of approximately 9 mph (15 km/h) or
above.
To prevent the vehicle doors from locking,
deactivate the automatic central locking
(
page 155).
iTo signal turns while being towed with
hazard warning flasher in use, turn the SmartKey
in starter switch to position2 and activate
combination switch for left or right turn signal in
usual manner – only the selected turn signal will
operate.
Upon canceling the turn signal, the hazard
warning flasher will operate again.
iThe gear selector lever will remain locked in
park positionP and the SmartKey will not turn in
the starter switch if the battery is disconnected
or discharged. For more information, see “Bat-
tery” (
page 396) and “Jump starting”
(
page 399).
For information on manually unlocking the gear
selector lever, see (
page 373).