2007 MERCEDES-BENZ CLK550 COUPE ESP

356 Practical hints
What to do if …?
Lamps in instrument clusterGeneral information:
If any of the following lamps in the instru-
ment cluster fails to come on during thebulb self-check when switching on the igni-
tion, have the respective bulb checked and
replaced if necessary.
ProblemPossible cause/consequenceSuggested solution
-The yellow ABS indicator lamp
comes on while the engine is
running.The ABS has detected a malfunction and has
switched off. The BAS and the ESP® are also
switched off (see messages in the multifunc-
tion display).
The brake system is still functioning normally
but without the systems specified above.
If the ABS control unit is malfunctioning,
other systems such as the navigation
system* or the automatic transmission may
also be malfunctioning.
Continue driving with added caution.
Wheels will lock during hard braking,
reducing steering capability.
Read and observe messages in the
multifunction display (
page 370).
Have the system checked at an autho-
rized Mercedes-Benz Center as soon
as possible.
Failure to follow these instructions in-
creases the risk of an accident.
The charging voltage has fallen below
10 volts. The ABS has switched off.
The battery might not be charged sufficiently.Switch off electrical consumers that
are currently not needed, e.g. seat
heating*.
If necessary, have the generator and
battery checked.
When the voltage is above this value
again, the ABS is operational again.

357 Practical hints
What to do if …?
ProblemPossible cause/consequenceSuggested solution
-The yellow ABS indicator lamp
comes on while the engine is
running.The ABS is temporarily not available. The
ESP® and the BAS are also unavailable.
The system’s self-diagnosis may not be
completed yet.
The brake system is still functioning normally
but without the systems specified above.
Drive a short distance with added
caution at a vehicle speed of above
12 mph (20 km/h).
When the ABS indicator lamp goes
out, the ABS, the ESP
®, and the BAS
are available again.
If the ABS indicator lamp does not go out:
Continue driving with added caution.
Have the system checked at an autho-
rized Mercedes-Benz Center as soon
as possible.
Failure to follow these instructions in-
creases the risk of an accident.

362 Practical hints
What to do if …?
ProblemPossible cause/consequenceSuggested solution
vThe yellow ESP® warn-
ing lamp comes on while
the engine is running.The ESP® has been switched off with the
ESP® switch or has been switched off due
to a malfunction.
Risk of accident!
When the ESP
® is switched off it will not
stabilize the vehicle if the system recog-
nizes that the vehicle starts to skid or that
a wheel is spinning.
The cruise control is deactivated and can-
not be switched on.
Switch the ESP® back on (page 93).
Exceptions: (
page 92).
If leaving the ESP® switched off, adapt your speed
and driving to the prevailing road, weather and
traffic conditions.
If the ESP
® cannot be switched on:
Continue driving with added caution.
Observer additional messages that may appear in
the multifunction display (
page 370).
Have the system checked at an authorized
Mercedes-Benz Center as soon as possible.
vThe yellow ESP® warn-
ing lamp flashes while
driving.The ESP® or traction control has come
into operation because of detected trac-
tion loss in at least one tire.
The cruise control is deactivatedWhen driving off, apply as little throttle as possi-
ble.
While driving, ease up on the accelerator.
Adapt your speed and driving to the prevailing
road, weather and traffic conditions.
Do not deactivate the ESP®.
Exceptions: (
page 92).
Failure to follow these instructions increases the risk
of an accident.

370 Practical hints
What to do if …?
Text messages
Display messagePossible cause/consequencePossible solution
ABSABS, ESP
inoperative
See Operator’s Man.The ABS and ESP® are not available due to
a malfunction.
The BAS is also deactivated.
The brake system is still functioning
normally but without but without the
systems specified above.Continue driving with added caution.
Wheels will lock during hard braking,
reducing steering capability.
Have the system checked at an autho-
rized Mercedes-Benz Center as soon
as possible.
Failure to follow these instructions in-
creases the risk of an accident.
Cruise con-
trol and
SPEEDTRONICinoperativeCruise control is malfunctioning.Have the cruise control checked by an au-
thorized Mercedes-Benz Center.
ESPinoperative
See Operator’s Man.The ESP® has switched off due to a
malfunction.
The ABS and the BAS might not be opera-
tional.
The brake system is still functioning
normally but without the systems speci-
fied above.Continue driving with added caution.
Contact an authorized Mercedes-Benz
Center as soon as possible.
Failure to follow these instructions
increases the risk of an accident.

371 Practical hints
What to do if …?
Display messagePossible cause/consequencePossible solution
ESPunavailable
See Operator’s Man.The ESP® is temporarily not available.
The system’s self-diagnosis may not be
completed yet.
The ABS and the BAS might not be
operational.
The brake system is still functioning normally
but without the systems specified above.Drive a short distance with added
caution at a vehicle speed of above
12 mph (20 km/h).
When the message disappears, the
ESP
® is available again.
If the message does not disappear:
Continue driving with added caution.
Have the system checked at an autho-
rized Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions increas-
es the risk of an accident.
The charging voltage has fallen below 10 volts.
The ESP® has switched off.
The BAS may be switched off, too. The battery
may not be charged. The battery or the gener-
ator may be malfunctioning.
The ABS might not be operational.
The brake system is still functioning normally
but without the systems specified above.
Continue driving with added caution.
When the voltage is above this value
again, the ESP
® is operational again.
Have the system checked at an autho-
rized Mercedes-Benz Center as soon as
possible.

395 Practical hints
Where will I find...?
3Arrow
4Minispare wheel
5Vehicle tool kit storage well casing
6Vehicle tool kit
Remove vehicle tool kit6.Storing the vehicle tool kit
Place vehicle tool kit6 in vehicle tool
kit storage well casing5.
Place storage well casing2 over the
vehicle tool kit storage well casing5
and turn retaining screw1 clockwise
as far it will go to secure the Minispare
wheel.
Disengage trunk floor handle in upper
edge of trunk and lower trunk floor cov-
er.Vehicle jack
iArrow3 on vehicle tool kit storage well
casing5 must point in the direction of travel.
Otherwise you cannot place the storage well
casing2 on top and secure the Minispare
wheel with retaining screw1.
!To prevent damage, always disengage trunk
floor handle from upper edge of trunk and lower
trunk floor before closing the trunk.
Warning!G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface. Make sure the jack arm is
fully seated in the jack take-up bracket.
Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.

398 Practical hints
Where will I find...?
In case of a flat tire, you may temporarily
use the Minispare wheel when observing
the following restrictions:

Do not exceed a vehicle speed of
50 mph (80 km/h).

Drive to the nearest tire repair facility
to have the flat tire repaired or
replaced as appropriate.

Do not operate vehicle with more than
one Minispare wheel mounted.For more information, see “Rims and tires”
(
page 442).
Spare wheel bolts
The spare wheel bolts are fixed at the
Minispare wheel.
1Wheel bolt for light alloy rims
2Wheel bolt for Minispare wheel
(located in trunk with spare wheel)
Warning!G
The dimensions of the Minispare wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare wheel
mounted.
The Minispare wheel should only be used
temporarily, and should be replaced with a
regular road wheel as quickly as possible.
Do not switch off the ESP
® when a Minis-
pare wheel is mounted.
!Wheel bolts2 must be used when mount-
ing the Minispare wheel. The use of any wheel
bolts other than wheel bolts2 for the Minispare
wheel will physically damage the vehicle’s
brakes.
Warning!G
Make sure to use the original length wheel
bolts when remounting the original wheel
after it has been repaired.


411 Practical hints
Replacing bulbs
Reinsert bulb holder4 w i t h t h e b u l b i n
the lamp and turn clockwise.
Align housing cover2 and turn it
clockwise.
Front turn signal lamp bulb
Turn bulb socket1 counterclockwise
and remove it.
Press gently onto the bulb and turn
counterclockwise out of bulb
socket1.
Press the new bulb gently into bulb
socket1 and turn clockwise until it
engages.
Place bulb socket1 back into the
lamp and turn it clockwise.
Parking and standing lamp bulb
Turn housing cover2 counterclock-
wise and remove it.
Pull out bulb socket5 with the bulb.
Pull the bulb out of the bulb socket5.
Press the new bulb into bulb socket5.
Press bulb socket5 back into the
lamp.
Align housing cover2 and turn it
clockwise.
Additional turn signal lamps
The additional turn signal lamps in the ex-
terior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the additional turn signal unit
replaced by an authorized Mercedes-Benz
Center.
Front side marker lamp
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 128).
Tail lamp unit
Open trunk lid.
Swing the trim panel covering the cor-
responding rear lights to the side.
1Connector
2Tab
Disconnect electrical connector1.