2007 MERCEDES-BENZ CL500 System setting

424 Controls in detail
Driving systems
DISTRONIC Plus deactivates automatically
when:

the vehicle is secured with the elec-
tronic parking brake

the vehicle speed is below 20 mph
(30 km/h) and no preceding vehicle is
detected

the ESP® is in operation or switched off
with the ESP® switch (page 71)

you set the automatic transmission
toP, R, or N while driving

the radar sensors are switched off
(
page 272)

the vehicle rolls backward
The segments in the multifunction display
go out, an acoustic signal sounds, and the
message “DISTRONIC PLUS Off” appears in
the multifunction display for approximately
5 seconds.If the vehicle has been stopped by
DISTRONIC Plus and a malfunction occurs
in the system, the message “Brake immedi-
ately” will appear on the multifunction dis-
play. Step on the brake immediately to
prevent the vehicle from rolling.
DISTRONIC Plus is then switched off and
the message disappears.
Warning!G
DISTRONIC Plus switches off and releases
the brakes when the vehicle decelerates be-
low the minimum speed of 20 mph
(30 km/h) by operation of the system un-
less DISTRONIC Plus detects a vehicle di-
rectly ahead of you. At that time the driver
must apply the brakes in order to reduce ve-
hicle speed further or bring it to a stop.
!Setting the automatic transmission toN
while driving cancels the DISTRONIC Plus. How-
ever, the automatic transmission should not be
set toN while driving except to coast when the
vehicle is in danger of skidding (e.g. on icy
roads).
iDepressing the accelerator pedal does not
deactivate DISTRONIC Plus. After brief accelera-
tion (e.g. for passing), DISTRONIC Plus will re-
sume to the last set speed.

425 Controls in detail
Driving systems
Setting the following distance in
DISTRONIC Plus
You can set the specified following dis-
tance for DISTRONIC Plus by varying the
time setting between 1.0 and 2.0 seconds.
Using this time setting and the current
speed of your vehicle, DISTRONIC Plus cal-
culates and sets the required following dis-
tance to the preceding vehicle. The set
distance will be shown in the multifunction
display.The distance setting switch for the target
distance is located on the DISTRONIC Plus
lever.
1Distance setting switch for target dis-
tance
2To increase target distance
3To decrease target distanceIncreasing distance
Increasing the distance setting causes
DISTRONIC Plus to maintain a greater fol-
lowing distance to the preceding vehicle.
Move distance setting switch 1 in di-
rection 2.
Decreasing distance
Decreasing the distance setting causes
DISTRONIC Plus to maintain a shorter fol-
lowing distance to the preceding vehicle.
Move distance setting switch 1 in di-
rection 3.Warning!G
It is up to the driver to exercise discretion to
select the appropriate setting given road
conditions, traffic, driver’s preferred driving
style and applicable laws and driving recom-
mendations for safe following distance.

429 Controls in detail
Driving systems
Active Body Control (ABC)
The ABC system is an active, comput-
er-controlled system that hydraulically ad-
justs the suspension at all four wheels in
response to various driving situations. It
automatically selects the optimum suspen-
sion tuning and ride height for your vehicle.
Vehicle level controlYour vehicle automatically adjusts its ride
height to:

increase vehicle safety

reduce fuel consumption
The vehicle chassis ride height is raised or
lowered according to the selected level
setting and to the vehicle speed:

With increasing speed, ride height is re-
duced by up to approximately 0.4 in
(10 mm).

With decreasing speed, the ride height
is again raised to the selected vehicle
level.The following vehicle level settings can be
selected when the vehicle is stationary:
Select the “Raised” level setting only when
required by current driving conditions.
Otherwise:

Fuel consumption may increase.

Handling may be impaired.
Warning!G
To help avoid personal injury, keep hands
and feet away from wheel housing area, and
stay away from under the vehicle when
lowering the vehicle chassis.
iThese height adjustments are so small that
you may not notice any change.
Level
NormalFor driving on normal roads.
The indicator lamp is off.
RaisedFor driving on rough roads or
with snow chains. The indica-
tor lamp is on.
iThe selected vehicle level setting remains
stored in memory even if the engine is turned off
and restarted.

430 Controls in detail
Driving systems
1Vehicle level control switch
2Indicator lamp
Selecting a higher level
Start the engine.
If indicator lamp2 is off:
Press switch1.
Indicator lamp2 comes on. The vehi-
cle is raised to a higher level.Selecting a normal level
Start the engine.
If indicator lamp2 is on:
Press switch1.
Indicator lamp2 goes out. The vehicle
is adjusted to a normal level.
Suspension tuning
The suspension tuning is set according to:

your driving style

road surface conditions

the vehicle loading

your choice of suspension styleThe program mode selector switch (C/S)
(
page 399) is used to adjust the suspen-
sion tuning:
Start the engine.
Select the desired driving program.
Driving programSuspension tuning
CComfortcomfortable
(default setting)
SSportsporty
for dynamic driving

441 Controls in detail
Driving systems
Switching on Dynamic Rear View Moni-
tor
Switch on the ignition (page 336).
Switch on COMAND (page 81).
Move gear selector lever to position R
(reverse gear).
The COMAND display will show the
area behind the vehicle with guide lines
to help you reverse into a parking
place.Reverse parking (back-in parking)
This function helps you when you are re-
versing in a straight line or backing in at
any angle.
The space required by the vehicle for re-
versing is shown by guide lines.
When you turn the steering wheel to a
straight-ahead position, you will see the
guide lines on the COMAND display in the
following order:

there is a sudden change in tempera-
ture, for example when you drive out of
the cold into a heated garage in winter
(lens condensation)

the camera lens is dirty or covered, see
“Cleaning the Dynamic Rear View
Monitor lens*” (
page 560)

the rear of your vehicle is damaged. In
this case, have the position and setting
of the camera checked by a qualified
technician. Contact an authorized
Mercedes-Benz Center.
Do not use the Dynamic Rear View Monitor
if the roads are icy, slippery or covered with
snow. The vehicle could slip causing the ac-
tual vehicle position to deviate from the one
shown on the COMAND display.
This may cause injury to you or others, or
damage the vehicle or objects.
Mounting tires/rims of other specification
than the original equipment tires/rims may
impair the function of the Dynamic Rear
View Monitor. Contact an authorized
Mercedes-Benz Center.
Warning!G
Use of Dynamic Rear View Monitor can be
dangerous if you are color-blind or have im-
paired color vision.
Only use Dynamic Rear View Monitor if you
can see and distinguish all colored guide
lines shown by Dynamic Rear View Monitor
on the COMAND display.
iThe Dynamic Rear View Monitor must be ac-
tivated in the instrument cluster control system
in order for it to be switched on (
page 269).
iIf you activate a different function on the
driver’s COMAND controls while reverse parking
or parallel parking, the image from the back-up
camera is interrupted.
To reactivate the camera, take the vehicle out of
reverse gear and then re-engage reverse gear
again.

447 Controls in detail
Driving systems
Switching on or off
You can only switch on the Night View As-
sist if

the SmartKey in the starter switch is
set to position2

it is dark

the light switch is set to * or B
or if the daytime driving lamps are
switched on

the automatic transmission is not in
positionR
1Night View Assist on or off
Press button1 up or down.
The Night View Assist image appears
on the multifunction display.
Image on multifunction display
When you switch on Night View Assist, the
image for the speed gauge changes on the
multifunction display. The speed gauge is
shown as a bar on the lower edge of the
multifunction display. The line for main
menus is no longer available. If you would
like to change a setting using the steering
wheel buttons, you must first switch off
Night View Assist.1Night View Assist image
2Speedometer display
iThe infrared headlamps only come on above
a speed of approximately 9 mph (15 km/h).
Therefore, when you are at a standstill, you do
not have a complete view and cannot check the
function of the Night View Assist.
iIf you change the brightness of the instru-
ment cluster while Night View Assist is switched
on, only the brightness of the multifunction dis-
play is changed.

448 Controls in detail
Driving systems
Adjusting instrument cluster illumina-
tion
1Knob
Make sure the Night View Assist is
switched on.
Brightening illumination: Turn
knob1 clockwise.
Dimming illumination: Turn knob1
counterclockwise.Dirty or fogged-up windshield
If the windshield in front of the camera is
fogged up on the inside or outside or if it is
dirty, the Night View Assist image is
diminished.Removing condensation
Check settings of automatic climate
control and change them, if necessary
(
page 453).
Swing the camera cover downward
(
page 561).
Cleaning inside of windshield
Clean inside of windshield in front of
camera with a soft, non-scratching
cloth (
page 561).
Warning!G
Please do not forget that your primary re-
sponsibility is to drive the vehicle. A driver’s
attention to the road must always be
his/her primary focus when driving. For
your safety and the safety of others, stop be-
fore trying to remove window fogging or
cleaning the window in front of the
Night View Assist camera.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet
(approximately 14 m) every second.

454 Controls in detail
Automatic climate control
The automatic climate control is operation-
al whenever the engine is running. You can
operate the climate control system in ei-
ther the automatic or manual mode. The
system cools or heats the interior depend-
ing on the selected interior temperature
and the current outside temperature.
It can only function optimally when you are
driving with the windows and the tilt/slid-
ing sunroof closed.
It is possible to completely deactivate the
climate control system (
page 455). Nearly all dust particles, pollutants and
odors are filtered out before outside air en-
ters the passenger compartment through
the air distribution system.The following automatic climate control
functions can be operated via COMAND:
iIf you have the air distribution and air vol-
ume automatically controlled, you can adjust the
temperature, footwell temperature and air flow.
The following basic settings are recommended:

Automatic air distribution control
(
page 453)

Temperature: 72°F (22°C) (page 456)

Footwell temperature: 0 (page 249)

Air flow: focused (page 249)
Warning!G
Follow the recommended settings for heat-
ing and cooling given on the following pages
and in the “COMAND automatic climate
control” section (
page 244). Otherwise
the windows could fog up, impairing visibili-
ty and endangering you and others.
iSevere conditions (e.g. strong air pollution)
may require replacement of the filter before its
scheduled interval. A clogged filter will reduce
the air volume to the interior.
If the vehicle interior is hot, ventilate the interior
before driving off, see “Summer opening fea-
ture” (
page 376). The automatic climate con-
trol will then adjust the interior temperature to
the set value much faster.
Keep the air intake grille in front of the wind-
shield free of snow, leaves, sticks, and any other
debris.
Do not obstruct air volume by placing objects on
the air volume-through exhaust slots below the
rear window.
FunctionPage
Temperature245
Air distribution246
Air volume246
Switching off cooling (“ACOFF”)247
Central climate control (“Mono”)248
Footwell temperature249
Air flow from air vents249