Page 369 of 441
368 Practical hints
Replacing bulbs
Bulbs Front lamps
Rear lamps
LampType
1Additional turn signal
lampLED
2Halogen headlamp:
Turn signal lamp
Bi-Xenon* headlamp:
Turn signal lamp
1156 A
2357 A
3Halogen headlamp:
Low beam
Bi-Xenon* headlamp:
Low and high beam
1
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Xenon bulbs yourself. Contact an
authorized Mercedes-Benz Center.
H7 (55 W)
D2S-35 W
4Halogen headlamp:
High beam/high beam
flasher
Bi-Xenon* headlamp:
High beam flasher
H7 (55 W)
H7 (55 W)
Parking and standing
lampW5W
LampType
5Front fog lampHB4 (51 W)
Corner-illuminating
front fog lamps*H7 (55 W)
6Side marker lampW5W
LampType
7High mounted brake
lampLED
8Brake lampP21W
9Turn signal lampPY 21 W
aParking and side
marker lampP 21/5 W
bBackup lampP21W
cLicense plate lampsC5W
dRear fog lamp
(driver’s side only), tail
and standing lampP 21/4 W
Page 370 of 441

369 Practical hints
Replacing bulbs
Notes on bulb replacement
Only use 12 volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:
Additional turn signals in the exterior
rear view mirrors
High mounted brake lamp
Xenon* lamps
Front fog lamps
Front side marker lamps
Warning!G
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before
changing a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas.
A bulb can explode if you
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
!Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the
vehicle. Only have the LEDs replaced by an
authorized Mercedes-Benz Center.
Page 371 of 441
370 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 109).
Open the hood (page 274).
Halogen headlamp
1Housing cover for low beam headlamp
2Housing cover for high beam head-
lamp, parking and standing lamp3Bulb socket for turn signal lamp bulb
4Bulb socket for low beam bulb
5Bulb socket for high beam bulb
6Bulb socket for parking and standing
lamp bulbLow beam bulb
Press the clamp on housing cover1
and remove it.
Pull the electrical connector off.
Turn bulb socket4 counterclockwise
and take out the bulb.
Insert the new bulb so that its socket
locates in the recess of the lamp
housing.
Turn bulb socket4 clockwise until it
engages.
Plug the electrical connector onto the
bulb.
Align housing cover1 and press until
it engages.
Page 372 of 441

371 Practical hints
Replacing bulbs
High beam bulb
Press the clamp on housing cover2
and remove it.
Pull the electrical connector off.
Turn bulb socket5 counterclockwise
and take out the bulb.
Insert the new bulb so that its socket
locates in the recess of the lamp
housing.
Turn bulb socket5 clockwise until it
engages.
Plug the electrical connector onto the
bulb.
Align housing cover2 and press until
it engages.Front turn signal lamp bulb
Turn bulb socket3 with the bulb
counterclockwise and remove it.
Press gently onto the bulb and turn it
counterclockwise out of bulb
socket3.
Press new bulb gently into bulb
socket3 and turn clockwise until it
engages.
Place bulb socket3 back into the
lamp and turn it clockwise.Parking and standing lamp bulb
Press the clamp on housing cover2
and remove it.
Pull out bulb socket6 with the bulb.
Pull the bulb out of bulb socket6.
Press the new bulb into bulb socket6.
Press bulb socket6 back into the
lamp.
Align housing cover2 and press until
it engages.
Page 373 of 441
372 Practical hints
Replacing bulbs
Bi-Xenon* headlamp
1Housing cover for Bi-Xenon headlamp
2Housing cover for high beam flasher,
parking and standing lamp3Bulb socket for turn signal lamp bulb
4Bulb socket for high beam flasher bulb
5Bulb socket for parking and standing
lamp bulbHigh beam flasher bulb
Press the clamp on housing cover2
and remove it.
Pull the electrical connector off.
Turn bulb socket4 counterclockwise
and take out the bulb.
Insert the new bulb so that its socket
locates in the recess of the lamp
housing.
Turn bulb socket4 clockwise until it
engages.
Plug the electrical connector onto the
bulb.
Align housing cover2 and press until
it engages.
Warning!G
Do not remove the cover1 for the
Bi-Xenon headlamp. Because of high voltage
in Bi-Xenon lamps, it is dangerous to replace
the bulb or repair the lamp and its compo-
nents. We recommend that you have such
work done by a qualified technician.
Page 374 of 441

373 Practical hints
Replacing bulbs
Front turn signal lamp bulb
Turn bulb socket3 with the bulb
counterclockwise and remove it.
Press gently onto the bulb and turn it
counterclockwise out of bulb
socket3.
Press new bulb gently into bulb
socket3 and turn clockwise until it
engages.
Place bulb socket3 back into the
lamp and turn it clockwise.
Parking and standing lamp bulb
Press the clamp on housing cover2
and remove it.
Pull out bulb socket5 with the bulb.
Pull the bulb out of bulb socket5.
Press the new bulb into bulb socket5.
Press bulb socket5 back into the
lamp.
Align housing cover2 and press until
it engages.Additional turn signal lamp bulbs
The additional turn signal lamps in the
exterior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to
function, the entire turn signal unit must be
replaced. Have the turn signal unit
replaced by an authorized Mercedes-Benz
Center.
Front side marker lamp bulbs
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 109).
Open the trunk (page 96).
Tail lamp unit
1Latch
Page 375 of 441
374 Practical hints
Replacing bulbs
Fold the corresponding trim panel to
the side.
Turn latch1 to vertical position and
remove the bulb carrier.
Bulb carrier
2Brake lamp bulb
3Backup lamp bulb
4Rear fog lamp (driver’s side only),
tail and standing lamp bulb
5Parking and side marker lamp bulb
6Turn signal lamp bulb
Press gently onto the respective bulb
and turn counterclockwise out of its
bulb socket.
Press the new bulb gently into its bulb
socket and turn clockwise until it
engages.
Reinstall the bulb carrier and lock it
again with latch1.
Reinstall the trim panel.License plate lamp
1Screw
2License plate lamp
Loosen both screws1.
Remove the license plate lamp2.
Replace the bulb.
Reinstall the license plate lamp2.
Retighten screws1.
Page 376 of 441

375 Practical hints
Replacing wiper blades
Replacing wiper blades
Removing and installing wiper blades
Remove SmartKey from starter switch.
Removing wiper blades
1Unlocking
2Tab
Pull the tab2 in direction of arrow1.
The wiper blade is unlocked.
Lift up the wiper arm as far as you need
to remove the wiper blade.
Carefully fold the wiper arm back to
rest on the windshield.
Warning!G
For safety reasons, switch off wipers and
remove SmartKey from starter switch be-
fore replacing a wiper blade. Otherwise, the
wiper motor could suddenly turn on and
cause injury.
Warning!G
Wiper blades are components that are sub-
ject to wear and tear. Change the wiper
blades twice a year, preferably in the spring
and fall. Otherwise the windows will not be
properly wiped. As a result, you may not be
able to observe surrounding traffic condi-
tions and could cause an accident.
!Never open the hood when the wiper arms
are folded forward.
For your convenience, we recommend that you
have this work carried out by an authorized
Mercedes-Benz Center.
!Do not pull on the wiper blade inserts. They
could tear.
!Hold on to the wiper arm. If released, the
force of the impact from the tensioning spring
could crack the windshield.