2007 KIA CARNIVAL torque

5.Install the brake hose bracket bolt (A, B) to the axle assembly.
Tightening torque Nm (kgf.m, lb - ft) :
6.9 ~ 11 (0.7 ~ 1.1, 5.1 ~ 8.0)
6.Install the wheel and the tire (A) to the front hub (B).
Tightening torque Nm (kgf.m, lb - ft) :
90 ~ 110 (9 ~ 11, 65.1 ~ 79.5)
Be careful not to damage the hub bolts(C) when installing the front wheel and tire(A).
DISASSEMBLY
1.Using the special tool (09546- 26000), compress the coil spring (A).

b.Install the coil spring wth the identification mark directed toward the knuckle.
3. After fully extending the piston rod, install the spring upper seat and insulator assembly.
4. After seating the upper and lower ends of the coil spring (A) in the upper and lower spring seat grooves (B)
correctly, tighten new self - locking nut temporarily.
5.Remove the special tool (09546- 26000).
6. Tighten the self - locking nut to the specified torque.
Tightening torque :
60 ~ 70 Nm (6 ~7 kgf.m, 43.4 ~ 50.6 lb - ft)

2.Apply soap solution to the following parts.
a. Outer surface of the bushing.
b. Inner surface of the lower bushing mounting part.
3. Using the special tools(09214- 32000 & 09216 - 21100), install the busing on the lower arm.
Insert bushing in the direction shown in the illustration.
Separation force is over 100 Nm (1000Kgf, 2204 lbf)
INSTALLATION
1. Install the lower arm mounting bolts (A, B).
Tightening torque Nm (kgf.m, lb - ft) :
160 ~ 180 (16 ~ 18, 115.7 ~ 130.2)

2.Install the front lower arm (A) ball joint mounting bolt (B) to the knuckle.
Tightening torque Nm (kgf.m, lb - ft) :
90 ~ 120 (9 ~ 12, 65.1 ~ 86.8)
3.Install the wheel and the tire(A) to the front hub(B).
Tightening torque Nm (kgf.m, lb - ft) :
90 ~ 110 (9 ~ 11, 65.1 ~ 79.5)
Be careful not to damage the hub bolts(C) when installing the front wheel and tire(A).
INSPECTION
1.Check the bushing for wear and deterioration.
2. Check the lower arm for bending or breakage.
3. Check the ball joint dust cover for cracks.

4.Check all bolts.
5. Check the lower arm ball joint for rotating torque.
(1) If a crack is noted in the dust cover, replace the ball joint assembly.
(2) Move the ball joint stud several times in a circular motion.
(3) Measure the ball joint rotating torque.
Standard value :
1 ~ 3.5 Nm (10 ~ 35 kgf.cm, 0.72 ~ 2.53 lb - ft)
Measure torque using the special tool(09532- 11600) and torque wrench at the range of 0.5 - 2 rpm after
moving the ball joint stud 10 times at room temperature.
(4)If the rotating torque is below the lower limit of standard value, replace the ball joint assembly.
(5) Even if the rotating torque is below the lower limit of the standard value, the ball joint may be reused unless it
has drag and excessive play.

INSTALLATION
1.Install the bushing (B) on the stabilizer bar (A).
Bring clamp (C) of stabilizer bar (A) into contact with bushing (B).
2. Install the bracket on the bushing (B).
3. After tightening the bolts of the bushing bracket temporarily, install the bushing bracket on the opposite side.
4. Install the stabilizer bar bracket mounting bolts (A) to the sub frame.
Tightening torque Nm (kgf.m, lb - ft) :
39 ~ 60 (3.9 ~ 6.0, 28.2 ~ 43.4)
5.After lifting the jack which supports the sub frame, install the four bolts (A) of the sub frame and the eight bolts (B)
of the guide bracket.
Tightening torque Nm (kgf.m, lb - ft) :
Bolt (A) : 160 ~ 180 (16 ~ 18, 115.7 ~ 130.2)
Bolt (B) : 45 ~ 60 (4.5 ~ 6.0, 32.5 ~ 43.4)

6.Install the engine mounting bolts (A, B)
Tightening torque Nm (kgf.m, lb - ft) :
65 ~ 85 (6.5 ~ 8.5, 47.0 ~ 61.5)
7.Install both sides of the lower arm (A) mounting bolts(B).
Tightening torque Nm (kgf.m, lb - ft) :
90 ~ 120 (9 ~ 12, 65.1 ~ 86.8)
8.Install both sides of the tie rod end (A) self - locking nuts (B). Insert cooter pin (C) after nut is torqued to
specification.

specification.
Tightening torque Nm (kgf.m, lb - ft) :
65 ~ 80 (6 ~ 8, 43.4 ~ 57.8)
9.Install the front stabilizer link (A) nut (B) to the strut assembly.
Tightening torque Nm (kgf.m, lb - ft) :
100 ~ 120 (10 ~ 12, 72.3 ~ 86.8)
10. Install the wheel and the tire (A) to the front hub (B).
Tightening torque Nm (kgf.m, lb - ft) :
90 ~ 110 (9 ~ 11, 65.1 ~ 79.5)
Be careful not to damage the hub bolts(C) when installing the front wheel and tire(A).
11. Install the connecting bolt (A) between the steering universal joint assembly (B) and the pinion assembly.