2007 KIA CARNIVAL lock

2007 > 2.7L V6 GASOLINE >
TROUBLESHOOTING
Symptom Suspect area Remedy
Engine misfire with
abnormal internal
lower engine noises. Worn crankshaft bearings.
Loose or impropes engine drive plate.
Replace the crankshaft and bearings as
required.
Repair or replace the drive plate as required.
Worn piston rings.
(Oil consumption may or may not cause the
engine to misfire.) Inspect the cylinder for a loss of compression.
Repair or replace as required.
Worn crankshaft thrust bearings Replace the crankshaft and bearings as
required.
Engine misfire with
abnormal valve train
noise. Stuck valves.
(Carbon buildup on the valve stem)
Repair or replace as required.
Excessive worn or mis - aligned timing chain. Replace the timing chain and sprocket as
required.
Worn camshaft lobes. Replace the camshaft and valve lifters.
Engine misfire with
coolant consumption. a.
Faulty cylinder head gasket and/or
cranking or other damage to the cylinder
head and engine block cooling system.
b. Coolant consumption may or may not
cause the engine to overheat. a.
Inspect the cylinder head and engine
block for damage to the coolant passages
and/or a faulty head gasket.
b. Repair or replace as required.
Engine misfire with
excessive oil
consumption. Worn valves, guides and/or valve stem oil
seals.
Repair or replace as required.
Worn piston rings.
(Oil consumption may or may not cause the
engine to misfire) a.
Inspect the cylinder for a loss of
compression.
b. Repair or replace as required.
Engine noise on start -
up, but only lasting a
few seconds. Incorrect oil viscosity.
a.Drain the oil.
b. Install the correct viscosity oil.
Worn crankshaft thrust bearing. a.Inspect the thrust bearing and crankshaft.
b. Repair or replace as required.
Upper engine
noise,regardless of
engine speed. Low oil pressure.
Repair or replace as required.
Broken valve spring. Replace the valve spring.
Worn or dirty valve lifters. Replace the valve lifters.
Stretched or broken timing chain and/or
damaged sprocket teeth. Replace the timing chain and sprockets.
Worn timing chain tensioner, if applicable. Replace the timing chain tensioner as
required.
Worn camshaft lobes. a.Inspect the camshaft lobes.
b. Replace the timing camshaft and valve
lifters as required.
Worn valve guides or valve stems. Inspect the valves and valve guides,then
repair as required.
Stuck valves. Carbon on the valve stem or
valve seat may cause the valve to stay open. Inspect the valves and valve guides, then
repair as required.
Worn drive belt, idler, tensioner and bearing. Replace as required.
Lower engine
noise,regardless of Low oil pressure.
Repair as required.

noise,regardless of
engine speed.Loose or damaged drive plate.
Repair or replace the drive plate.
Damaged oil pan, contacting the oil pump
screen. a.
Inspect the oil pan.
b. Inspect the oil pump screen.
c. Repair or replace as required.
Oil pump screen loose, damaged or
restricted. a.
Inspect the oil pump screen.
b. Repair or replace as required.
Excessive piston- to- cylinder bore clearance. a.Inspect the piston, piston pin and cylinder
bore.
b. Repair as required.
Excessive piston pin- to- piston clearance. a.Inspect the piston, piston pin and the
connecting rod.
b. Repair or replace as required.
Excessive connecting rod bearing clearance Inspect the following components and repair
as required.
a. The connecting rod bearings.
b. The connecting rods.
c. The crankshaft pin journals.
Excessive crankshaft bearing clearance. Inspect the following components, and repair
as required.
a. The crankshaft bearings.
b. The crankshaft main journals.
c. The cylinder block.
Incorrect piston, piston pin and connecting rod
installation a.
Verify the piston pins and connecting rods
are installed correctly.
b. Repair as required.
Engine noise under
load. Low oil pressure
Repair or replace as required.
Excessive connecting rod bearing clearance . Inspect the following components and repair
as required :
a. The connecting rod bearings.
b. The connecting rods.
c. The crankshaft.
Excessive crankshaft bearing clearance. Inspect the following components, and repair
as required.
a. The crankshaft bearings.
b. The crankshaft main journals.
c. The cylinder block.
Engine will not crank-
crankshaft will not
rotate. Hydraulically locked cylinder.
a. Coolant/antifreeze in cylinder.
b. Oil in cylinder.
c. Fuel in cylinder. a.
Remove spark plugs and check for fluid.
b. Inspect for broken head gasket.
c. Inspect for cracked engine block or
cylinder head.
d. Inspect for a sticking fuel injector and/or
leaking fuel regulator.
Broken timing chain and/or timing chain
and/or timing chain gears. a.
Inspect timing chain and gears.
b. Repair as required.
Material in cylinder. a. Broken valve
b. Piston material
c. Foreign material a.
Inspect cylinder for damaged components
and/or foreign materials.
b. Repair or replace as required.

2007 > 2.7L V6 GASOLINE >
Compression pressure inspection
If the there is lack of power, excessive oil consumption or poor fuel economy, measure the compression
pressure.
1. Warm up the engine until the normal operating temperature becoming 80~95°C(176~203°F).
2. Remove the surge tank.
3. Remove the ignition coil connectors(B) and ignition coils.
4.Using a 16mm plug wrench, remove the 6 spark plugs.
5. Check cylinder compression pressure.
(1) Insert a compression gauge into the spark plug hole.
(2) Open the throttle fully.
(3) With the fully - open throttle in cranking, measure the compression pressure.
Always use a fully charged battery to get the engine speed of 250 rpm or more.
Repeat steps 1) through 3) for each cylinder.
This measurement must be done in as short a time as possible.
Compression pressure: 1,176.79kPa (12.0kgf/cm², 170.68psi) - 200 ~ 250rpm
Minimum pressure: 1,029.69kPa (10.5kgf/cm², 149.34psi)
Difference between cylinders: 98.07kPa (1.0kgf/cm², 14.22psi)
(4) If the compression pressure in 1 or more cylinders is lower than the specification above, pour a small amount
of engine oil into the cylinder through the spark plug hole, repeat the steps (1) through (3) for the cylinder and
measure the pressure again.
a. If adding oil increases the pressure up, the piston rings or cylinder bores might be worn or damaged.
b. If the pressure doesn't increase, a valve may be sticking or seating may be improper, or there may be
leakage from the gasket.
6. Reinstall the spark plugs.
7. Install the ignition coils and connect ignition coil connectors.
8. Install the surge tank.
VALVE CLEARANCE INSPECTION AND ADJUSTMENT
Inspect and adjust the valve clearance when the engine is cold (Engine coolant temperature : 20°C
±5°C(59~77°F)) and cylinder head is installed on the cylinder block.

1.Remove the engine cover.
2. Remove air cleaner assembly.
3. Remove the surge tank.
4. Remove the cylinder head cover.
(1) Disconnect the ignition coil connector and remove the ignition coil.
(2) Remove the cylinder head cover.
5.Set the piston of the No.1 cylinder to TDC(Top Dead Center) position.
(1) Turn the crankshaft pulley clockwise and align its groove with the timing mark "T" of the timing chain cover.
(2) Check that the timing marks of the camshaft sprocket are in straight line on that of the cylinder head cover
surface as shwn in the illustration. It makes the piston of the No.1 cylinder position at TDC.
If not, turn the crankshaft one revolution clockwise.
6. Inspect the intake and the exhaust valve clearance.
(1) With the piston of the No.1 cylinder positioning at TDC, the valves which can be measured its clearance are as
shown below.
Measurement method.
a. Using a thickness gauge, measure the clearance between the tappet and the base circle of camshaft.
b. Record the out - of- specification valve clearance measurements. They will be used later to determine the
required adjusting tappet for replacement.

Specification
Limit (Engine coolant temperature : 20°C [68°F])
Intake : 0.10 ~ 0.30mm (0.0039 ~ 0.0118in.)
Exhaust : 0.20 ~ 0.40mm (0.0079 ~ 0.0157in.)
(2) Turn the crankshaft pulley one revolution (360°) clockwise and align the groove with the timing mark "T" of the
timing chain cover.
(3) With the piston of the No.4 cylinder positioning at TDC, the valves which can be measured its clearance are as
shown below.
7.Adjust the intake and the exhaust valve clearances.
(1) Set the piston of the No.1 cylinder to the TDC/position.
(2) Remove the timing belt.
(3) Remove the camshaft bearing caps(A, B).
(4)Remove the camshaft assembly.
(5) Remove MLA(Mechanical Lash Adjuster)s.
(6) Measure the thickness of the removed tappet using a micrometer.
(7)Calculate the thickness of a new tappet so that the valve clearance comes within the specified value.
T : Thickness of removed tappet
A : Measured valve clearance

N : Thickness of new tappet
Intake : N = T + [A - 0.20mm(0.0079in.)]
Exhaust : N = T + [A - 0.30mm (0.0118in.)]
(8) Select a new tappet with a thickness as close as possible to the calculated value.
Tappets are available with 41different size increments of 0.015mm (0.0006in.) from 3.00mm (0.118in.) to
3.600mm (0.1417in.)
(9) Place a new tappet on the cylinder head.
Apply engine oil on the periphery surface of the selected tappet.
(10) Install the intake and exhaust camshafts.
(11) Install the bearing caps.
(12) Install the timing belt.
(13) Turn the crankshaft two revolutions in the operating direction(clockwise) and realign crankshaft sprocket and
camshaft sprocket timing marks(A).
(14) Recheck the valve clearance.
Specification (Engine coolant temperature: 20°C[68°F])
Intake : 0.17 ~ 0.23mm (0.0067 ~ 0.0090in.)
Exhaust : 0.27 ~ 0.33mm (0.0106 ~ 0.0129in.)

Valve stem to valve
guide clearanceIntake
0.020 ~ 0.050mm(0.0008 ~ 0.0020in.) 0.10mm(0.0039in.)
or less
Exhaust 0.035 ~ 0.065mm(0.0014 ~ 0.0026in.) 0.13mm(0.0051in.)
or less
Valve guide
Inner diameter Intake 6.000 ~ 6.015mm(2.2362 ~ 2.2368in.)
Exhaust 6.000 ~ 6.015mm(2.2362 ~ 2.2368in.)
Length Intake 45.8 ~ 46.2mm(1.8031 ~ 1.8189in.)
Exhaust 46.8 ~ 47.2mm(1.8425 ~ 1.8583in.)
Valve spring
Free length 46.8mm(1.8425in.)
Load Height: 35mm 180.5 ~ 199.5N(18.4 ~ 20.3Kgf, 40.6 ~ 44.8lb)
Height: 26.5mm 342 ~ 378N(34.9 ~ 38.6Kgf, 76.9 ~ 85.1lb)
Out of squareness 1.5° or less
MLA(Mechanical Lash Adjuster)
MLA outer diameter Intake 29.964 ~ 29.980mm(1.1797 ~ 1.1803in.)
Exhaust 29.964 ~ 29.980mm(1.1797 ~ 1.1803in.)
Cylinder head
tappet bore inner
diameter Intake
30.000 ~ 30.025mm(1.1811 ~ 1.1821in.)
Exhaust 30.000 ~ 30.025mm(1.1811 ~ 1.1821in.)
MLA to tappet bore
clearance Intake
0.020 ~ 0.061mm(0.0008 ~ 0.0024in.) 0.07mm(0.0027in.)
or less
Exhaust 0.020 ~ 0.061mm(0.0008 ~ 0.0024in.) 0.07mm(0.0027in.)
or less
Valve clearance
Intake 0.17 ~ 0.23mm (0.0067 ~ 0.0090in.) 0.10 ~ 0.30mm
(0.0039 ~
0.0118in.)
Exhaust 0.27 ~ 0.33mm (0.0106 ~ 0.0129in.) 0.20 ~ 0.40mm
(0.0078 ~
0.0157in.)
Cylinder block
Cylinder bore 96.00 ~ 96.03mm (3.7795 ~ 3.7807in.)
Flatness of gasket surface Less than 0.05mm (0.0019in.)
[Less than 0.02mm (0.0008in.) / 150x150]
Piston
Piston outer diameter 95.96 ~ 95.99mm(3.7779 ~ 3.7791in.)
Piston to cylinder clearance 0.03 ~ 0.05mm(0.0012 ~ 0.0020in.)
Ring groove width No. 1 ring groove 1.22 ~ 1.24mm (0.0480 ~ 0.0488in.)
No. 2 ring groove 1.22 ~ 1.24mm (0.0480 ~ 0.0488in.)
Oil ring groove 2.01 ~ 2.03mm (0.0791 ~ 0.0799in.)
Piston O.S. 0.25mm(0.0098in.)
Piston ring
Side clearance No. 1 ring 0.04 ~ 0.08mm(0.0016 ~ 0.0031in.) 0.1mm(0.0039in.)

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Remove the engine cover.
2. Remove the front right wheel and tire.
3. Remove the right side cover.
4. Remove the drive belt(A), the idler(B) and the tensioner(C).
In removing the drive belt, fix a tool in the auto tensioner pulley bolt and turn the bolt counter clockwise.
5. Remove the timing belt upper cover(A).
6.Align the groove of the pulley with the timing mark of the timing belt cover by turning the crankshaft pulley
clockwise. Check if the timing mark of the camshaft sprocket is aligned with that of the cylinder head cover at the
moment.
(No.1 cylinder piston at TDC)
7.Remove the engine mounting bracket(A).