2007 ISUZU KB P190 wheel torque

3E-6 WHEELS AND TIRES
SERVICING
Servicing refers to general maintenance procedures to be performed by qualified service personnel.




WHEEL NUT TORQUES
W heel Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
117.7 ± 9.8 (12 ± 1.0 / 86.8 ± 7.2)





TIRE ROTATION
For of radial tires, interchange the front and the rear wheels on
the same side as shown in the figure.





If one-sided tire wear appears on radial tires, rotate the wheels
as shown in the figure.

Note:
After rotation, adjust the front and rear tire pressure and be sure to check wheel nut tightness.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

WHEELS AND TIRES 3E-9
Important Operations
1. Tire Assembly
To assemble, align the match mark (approx. 10mm diameter
paint mark) on the wheel with the match mark (approx. 8mm
diameter red paint mark) on the tire. If the match mark on the
wheel has disappeared, align with air valve instead.

2. Wheel and Tire Assembly





3. Wheel Nut
Tighten wheel nuts in numerical order.
W heel Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
117.7 ± 9.8 (12 ± 1.0 / 86.8 ± 7.2)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4B-8 REAR AXLE
SERVICING
Rear Axle Oil Replacement
Oil Capacity liters (US/UK gal.)

Specified gear oil GL5 (API grade)(STD)
GL5LSD (LSD)

φ220mm 2.4 (0.63/0.53)
φ194mm 1.6 (0.42/0.35)
Filler Plug and Drain Plug Torque N ⋅m (kgf ⋅m/lb ⋅ft)
78 (8.0/58)

Axle Shaft Roller Bearing Endplay
Inspection
1. Raise and suitably support vehicle.
2. Remove the wheel and brake drum.
3. Inspect the axle shaft roller bearing endplay using dial gauge.
Endplay mm (in
)
Standard 0 ~ 0.2 (0 ~ 0.008)
If the endplay exceeds 0.2mm (0.008 in), replace the
axle shaft roller bearings.
Refer to Rear Axle Reassembly.

RTW 34BSH000101


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-15
Reassembly
1. Using the oil seal installer 5-8840-2202-0 and
grip 5-8840-0007-0, install new axle case oil seal.




RTW 54BSH000301

Note :
Confirm that the dimension : A should be 34.5 –
36.1 mm (1.36 – 1.42 in)







A03R300004

2. Install new oil seal in bearing holder, using the oil seal installer 5-8840-2404-0.






RTW 54BSH000501
Legend
1. Oil Seal
2. Bearing Holder


3. Drive wheel pin into axle shaft flange, using a hammer.
4. Differential assembly a. Clean the mating surface of axle case and differential carrier.
b.
Apply Three Bond 1215 (TB1215) or
equivalent on the surface of differential
assembly as flowing illustration.


RTW 74BSH000301
Legend
a. 3 mm (0.12 in)

c. Tighten bolts and nuts to the specified torque.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-17
8. Certainly install new snap ring, use snap ring
pliers. W hen transform or damage, replace ne
w
one.




RTW 34BMH000101
Legend
1. Snap ring
2. Crevice
3. Retainer (with ABS)
Retainer (without ABS)


9. Insert a shim of sufficient thickness between
snap ring and end of retainer.

Standard 0 − 0.2 mm (0 − 0.008 in)

Crevice is measured using thickness gauge, and
when crevice exceeds 0.2 mm (0.008 in), it
adjusts so that is may become 0.2 mm (0.008 in)
or less using shim.

Shim Pats No. Thickness

1 9-41519110- ∗ 0.18 mm (0.0071 in)

2 8-97130387- ∗ 0.50 mm (0.0197 in)

Crevice No. of shim Total
mm (in)
1 2 mm (in)
1.0(0.0394)  2 1.00(0.0394)
0.9(0.0354) 2 1 0.86(0.0339)
0.8(0.0315) 1 1 0.68(0.0268)
0.7(0.0276) 1 1 0.68(0.0268)
0.6(0.0236)  1 0.50(0.0197)
0.5(0.0197)  1 0.50(0.0197)
0.4(0.0157) 2  0.36(0.0142)
0.3(0.0118) 1  0.18(0.0071)
0.2(0.0079) 1  0.18(0.0071)

10. Install axle shaft assembly in rear axle case
assembly.
a. Clean the mating surface of axle case and bearing holder.
b. Apply Three Bond 1215 (TB1215) o
r
equivalent on the surface of axle case
assembly.
Note:
When inserting an axle shaft, it inserts so that an
oil seal may not be damaged.
11. Install and tighten bearing holder fixing nut to the specified torque.
Torque : 84 N ⋅m (8.6 kgf ⋅m/62 lb ⋅ft)
12. Install wheel cylinder and tighten the bolt to the specified torque.
Torque : 9 N ⋅m (0.9 kgf ⋅m/78 lb ⋅in)
13. Install parking brake outer cable in back plate and inner cable in parking brake lever.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-19
17. Install brake pipe and ABS sensor and tighten it
to the specified torque.
Torque : ABS Sensor 8 N ⋅m (0.8 kgf ⋅m/69 lb ⋅in)
Brake Pipe 16 N ⋅m (1.6 kgf ⋅m/12 lb ⋅ft)
420R30003

18. Bleed brake pipe at the wheel cylinder. (Refer to
the section “Power-assisted Brake System”)
19. Install brake drum.
• Install propeller shaft. (Refer to Section “Rea
r
Propeller Shaft”.)
• Refill differential oil.
• Install wheel and tire.
• Lower vehicle.




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-6 FRONT WHEEL DRIVE
RECOMMENDED LIQUID GASKET
Type Brand Name Manufacture Remarks

RTV* Silicon Base ThreeBond 1207B
ThreeBond 1207C

ThreeBond 1215
Three Bond
Three Bond

Three Bond
For Engine Repairs


For Axle Case
Repairs, T/M
W ater Base ThreeBond 1141E Three Bond For Engine Repairs

Solvent ThreeBond 1104
BelcoBond 4
BelcoBond 401
BelcoBond 402 Three bond
Isuzu
Isuzu
Isuzu
For Engine Repairs
Anaerobic LOCTITE 515
LOCTITE 518 Loctite
Loctite All
* RTV : Room Temperature Vulcanizer

Note :
1. It is very important that the liquid gaskets listed above or their exact equivalent be used on the vehicle.
2. Be careful to use the specified amount of liquid gasket. Follow the manufacture's instructions at all times.
3. Be absolutely sure to remove all lubricants and moisture from the connecting surfaces before applying the liquid gasket.
The connecting surfaces must be perfectly dry.
4. LOCTITE 515 and LOCTITE 518 harden upon contact with a metal surface.
Do not apply LOCTITE 515 or LOCTITE 518 between two metal surfaces having a clearance of greater than 0.25 mm (0.01 in). Poor adhesion will result.

RECOMMENDED THREAD LOCKING AGENTS

LOCTITE Type LOCTITE Color Application Steps

LOCTITE 242
Blue 1. Completely remove all lubricant and moisture from the bolts and
the female threaded surfaces of the parts to be joined.
The surfaces must be perfectly dry.

LOCTITE 262
Red 2. Apply LOCTITE to the bolts.


LOCTITE 270
Green

LOCTITE 271
Red
3. Tighten the bolts to the specified torque.
4. W ait at least on hour before continuing the installation procedure.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-12 FRONT WHEEL DRIVE

17. Support the differential case by the jack.
18. Remove the front axle mounting bolts and nuts, lower the jack slowly. Remove the left side drive shaft end from the
knuckle, then lower the axle assembly from the vehicle.
CAUTION :
1. During the work, be sure that the axle assembly is supported securely.
2. Be careful not to damage the bellows of the power steering unit by interference.
3. Be careful not to damage the breather pipe and breather pip bracket of the shift on the fly by
interference.


Installation
1. Support the differential case by the jack.
2. Jack up the front drive axle assembly, install the left side drive shaft to the knuckle, then install the mount bolts and
nuts.
CAUTION :
1. Be careful not to damage the bellows of the power steering unit by interference.
2. Be careful not to damage the breather pipe and breather pip bracket of the shift on the fly by
interference.
3. When installing the drive shaft to the knuckle, be careful not to damage the oil seal inside of the knuckle.

RTW 34CSH000101
3. Tighten the mounting bolts and nuts to the specified torque.
Torque : 169 N·m (17.2kgf·m/124 lb·ft)



4. Install the right side knuckle with lower control arm to the
upper control arm.
Refer to Knuckle in Suspension section.
CAUTION :
When insert the drive shaft to the knuckle, be careful not
to damage the oil seal inside of the knuckle.

5.
Align the bolt hole of the lower control arm, install the bolts
and nuts.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007