2007 ISUZU KB P190 steering rack

6C – 24 FUEL SYSTEM







13. Throttle Position Sensor Harness Connector
(4JA1TC/4JH1TC only)
Reconnect the harness connector to the throttle position
sensor.
14. Power Steering Pump Bracket

15. Fan
16. Vacuum Hose
Connect the vacuum hose to the EGR valve and the
intake throttle.

Euro under Euro I Euro II Euro III
4JA1L without with with Not used
4JA1TC Not used Not used Not used With cooler
(EGR cooler)
4JH1TC without with with With
(EGR cooler)

17. Accelerator Control Cable
1) Connect the accelerator cable to the injection pump (4JA1T) the intake throttle. (4JA1TC/4JH1TC only)
18. Power Steering Pump Assembly
19. Drive Belt
Install the drive belt and adjust the belt tension.
20. Battery



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-16 ENGINE MECHANICAL (4JK1/4JJ1)

RTW 76ASH001401
14. Remove the breather hose and lower hose of the
radiator.
15. Remove the fan guide.
16. Remove the drive belt.
17. Remove the fan assembly.
18.Remove the radiator.
19.Remove the A/C compressor.





RTW 76ASH000701
Legend
1. A/C Compressor Bracket
2. A/C Compressor

• Disconnect the connector.
• Disconnect the A/C generator harness.
• Disconnect the terminal B cable and harness
connector from the generator.

20.Remove the power steering pump.
• Remove the bracket of power steering oil hose
(1).






LTW 56ASH000101
21.Remove the harness of engine, battery and earth
from the body side.
22.Remove the connector of the shift on the fly (4 ×4).
23.Remove the vacuum hose of brake master-vac.
24.Remove the front exhaust pipe.
25.Disconnect the fuel hose on the feed and return sides.
26.Install the engine hanger (special tool 5-8840- 2823-0).




RTW 56ASH004301
Legend
1. Engine Hanger (Front Side)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-17



RTW 56ASH004401
Legend
1. Engine Hanger (Rear Side)

27.Hang wire on the engine hanger and hoist to lift up
the engine slightly.
28.Remove the engine mount.
• Remove the fastening bolts for the engine mount
on the engine side.
29.Remove the engine assembly.
• Hoist the engine slightly to provide space to
remove the catalytic converter.
Installation
Notice:
Be absolutely sure that each harness is reconnected to
its original position.
1. Install the engine assembly.
• Hang wire on the engine hanger and hoist to lift up
the engine.
• Operate a hoist slowly to move the engine to the
place where it is to be installed.
• Make the transmission side lower and operate a
hoist slowly, pulling it backward to the engine.
2. Install the engine mount.
Tightening torque: 48 N ⋅
⋅⋅
⋅
m (4.9kg ⋅
⋅⋅
⋅
m / 35 lb ft)
3. Remove the engine hanger.
4. Install the catalytic converter.
Tightening torque: 27 N ⋅
⋅⋅
⋅
m (2.8kg ⋅
⋅⋅
⋅
m /20 lb ft)
5. Install the front exhaust pipe. Tightening torque: 67 N ⋅
⋅⋅
⋅
m (6.8kg ⋅
⋅⋅
⋅
m / 49 lb ft)
6. Install the fuel hose on the feed and return sides.
7. Install the vacuum hose of brake master-vac.
8. Install the connector of the shift on the fly (4 ×4).
9. Install the harness of engine, battery and earth to the body side.
10.Install the power steering pump.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5kg ⋅
⋅⋅
⋅
m / 18 lb ft)
• Install the bracket of power steering oil hose.
11.Install the A/C compressor.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5kg ⋅
⋅⋅
⋅
m / 18 lb ft)
• Install the connector.
12.Install the A/C generator harness.
• Install the terminal B cable and the harness
connector to the generator.
13.Install the radiator.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5kg ⋅
⋅⋅
⋅
m / 18 lb ft)
14.Install the fan assembly. Tightening torque: 8 N ⋅
⋅⋅
⋅
m (0.8kg ⋅
⋅⋅
⋅
m / 69 lb in)
15.Install the drive belt.
Refer to removal procedure for drive belt in this manual.
16.Install the fan guide.
17.Install the breather hose and lower hose of the radiator.
18.Install the engine harness clip (1).

RTW 76ASH001401
19.Install the radiator upper hose.
20.Install the intake hose (turbocharger -intercooler) (Standard output).
• Install the harness connector.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-51
Removal
1. Partially drain the engine coolant.
2. Remove the radiator upper hose.






RTW 56FSH000101
3. Remove the fan guide.




RTW 46BSH000101
Legend
1. Fan Guide
2. Clips
3. Lower Fan Guide
4. Fan Shroud


4. Remove the cooling fan and fan pulley.




RTW 56ASH025401
5. Remove the A/C compressor drive belt and fan
belt.
6. Remove the crank pulley.
7. Remove the power steering pump with hose.




RTW 56ASH021101
Legend
1. Power Steering Pump
2. Nut

• Disconnect the bracket (1) of power steering oil
hose.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-57
6. Remove the M6 bolt from the idle gear A.
7. Install the gear case cover. • Apply the liquid gasket (ThreeBond TB-1207B
or equivalent).


RTW 56ASH020101
Legend
1. Apply the liquid gasket

• Install the gasket in slot of the gear case cover.
• Tighten the bolts to the specified torque.
Tightening torque: 8 N ⋅
⋅⋅
⋅
m (0.8 kg ⋅
⋅⋅
⋅
m / 69 lb in)




RTW 56ASH012101
8. Install the vacuum pump.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
• Install the oil pipe (feed side and return side) o
f
vacuum pump.
• Install the vacuum pipe bracket and vacuum
pipe.
9. Install the power steering pump. • Tighten the nuts to the specified torque.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
• Connect the bracket (1) of power steering oil
hose.




LTW 56ASH000101

10. Install the crank pulley.
Tightening torque: 294 N ⋅
⋅⋅
⋅
m (30.0 kg ⋅
⋅⋅
⋅
m / 217 lb ft)
11. Install the A/C compressor drive belt and fan belt.
Refer to drive belt tension check procedure fo
r
Heating and air conditioning and Engine cooling in
this manual.
12. Install the cooling fan.
13. Install the fan guide.
14. Install the radiator upper hose.
15. Replenish the engine coolant.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-117
Removal
1. Remove the engine assembly.
Refer to removal procedure for “Engine Assembly” in this manual.
2. Remove the cylinder head.
Refer to removal procedure for “Cylinder Head” in this manual.
3. Remove the adjustment bracket of generator.
4. Remove the vacuum pump and pipe.
Refer to removal procedure for “Brake” in this manual.
5. Remove the power steering pump.
Refer to removal procedure for “Power Steering” in this manual.
6. Remove the water pump.
Refer to removal procedure for “W ater Pump” in this manual.
7. Remove the fuel supply pump.
Refer to removal procedure for “Fuel Suppl
y
Pump” in this manual.
8. Remove the crankshaft pulley.
Refer to removal procedure for “Crankshaft Front Oil Seal” in this manual.
9. Remove the gear case cover.
Refer to removal procedure for “Gear Case Cover” in this manual.
10. Remove the idle gear A and idle gear A shaft, idle gear C and idle gear C shaft.
Refer to removal procedure for “Timing Gea
r
Train” in this manual.





RTW 56ASH011401






RTW 56ASH011301
11. Remove the oil pump.
Refer to removal procedure for “Oil Pump” in this manual.
12. Remove the timing gear case (1) and gasket (2).





RTW 76ASH001201


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-118 ENGINE MECHANICAL (4JK1/4JJ1)
Installation
1. Install the packing of the timing gear case.
• Apply liquid gasket (ThreeBond 1207B o
r
equivalent) on the joint (1) of the cylinder block
and the crank case.




RTW 56ASH016301
2. Install the timing gear case.
• Install the timing gear case to match with the
dowel pins, install bolts in the order shown in
the illustration.



RTW 56ASH022601

Legend
1. Gear Case Assembly
2. Bolt L = 25 mm (0.98 in)
3. Bolt L = 60 mm (2.36 in)
4. Bolt L = 45 mm (1.77 in)
5. Bolt L = 35 mm (1.38 in)
6. Bolt L = 16 mm (0.63 in)
7. Bolt L = 20 mm (0.79 in)
8. Bolt L = 50 mm (1.97 in)
9. UP

• Tighten the bolts to the specified torque.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
• Tighten them in the order shown in the
illustration.
3. Install the oil pump.
Refer to installation procedure for “Oil Pump” in this manual.
4. Install the idle gear C shaft and idle gear C, idle gear A shaft and idle gear A.
Refer to installation procedure for “Timing Gea
r
Train” in this manual.
5. Install the gear case cover.
Refer to removal procedure for “Gear Case Cover” in this manual.
6. Install the crankshaft pulley.
Refer to removal procedure for “Crankshaft Front Oil Seal” in this manual.
7. Install the fuel supply pump.
Refer to installation procedure for “Fuel Suppl
y
Pump” in this manual.
8. Install the water pump.
Refer to installation procedure for “W ater Pump” in this manual.
9. Install the power steering pump.
Refer to removal procedure for “Power Steering” in this manual.
10. Install the vacuum pump and pipe.
Refer to removal procedure for “Brake” in this manual.
11. Install the adjustment bracket of generator.
Tighten the bolts to the specified torque.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
12. Install the cylinder head.
Refer to installation procedure for “Cylinder Head” in this manual.
13. Install the engine assembly.
Refer to installation procedure for “Engine Assembly” in this manual.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-156 ENGINE MECHANICAL (4JK1/4JJ1)
Oil Pump
Components




RTW 66AMF000701
Legend 1. Bolt 2. Oil Pump Assembly

Removal
1. Drain the engine coolant.
2. Remove the radiator upper hose.
3. Remove the upper fan shroud.
4. Remove the fan and fan clutch. • Loosen the fan clutch nuts.
• Remove the fan together with the fan clutch.
Take care not to damage the radiator core.
5. Remove the fan drive belt and pulley. • Loosen the tension adjust bolt on the generato
r
and A/C.
• Remove the fan drive belt with the fan pulley.
6. Remove the lower fan shroud.
7. Disconnect the power steering pump. • Disconnect the bracket of the power steering oil
hose clip (1).






LTW 56ASH000101


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007