2007 ISUZU KB P190 sensor

FRONT WHEEL DRIVE 4C1-11

Removal
1. Jack up the vehicle and support it using jack stand.
2. Remove the tire and wheel.
3. Remove the stone guard.
4. Remove the brake caliper fixing bolt and hang the caliper. Refer to Disc Brakes in Brake section.
5. Remove the antilock brake system speed sensor.
Refer to Front W heel Speed Sensor in Brake section.
6. Remove the hub and disc assembly.
Refer to Front Hub and Disc in this section.
7. Remove the propeller shaft, refer to Front Propeller Shaft in this section.
8. Loosen the height control arm of the torsion bar, then remove the torsion bar from lower control arm.
Refer to Torsion Bar in Suspension section.
9. Remove the suspension crossmember.
10. Remove the lower nut (1) of the stabilizer link.
11. Remove the lower bolt and nut (2) of the shock absorber.
12. Remove the tie-rod end from the knuckle.
Refer to Power Steering Unit in Steering Section.
13. Disconnect the breather hose of the front axle.
14. Disconnect the actuator connector.
15. Remove the bolts and nuts of the lower control arm (Frame side), then disconnect the lower control arm from frame.
16. Disconnect between the right side upper control arm and
the knuckle, then remove the knuckle with lower control
arm.
CAUTION :
When removing the knuckle, be careful not to damage the
oil seal inside of the knuckle.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-13


NOTE :
Adjust the buffer clearance before tighten the bolts and nuts of
the lower control arm.

6. Install the breather hose of the front axle.
7. Install the actuator connector of the shift on the fly.
8. Install the tie-rod end of the power steering unit to the knuckle, tighten the nut to the specified torque.
Torque : 98 N·m (10.0kgf·m/73 lb·ft)
9. Install lower bolts and nuts of the shock absorber, tighten it to the specified torque.
Torque : 93 N·m (9.5kgf·m/69 lb·ft)
10. Install lower nuts of the stabilizer link, tighten it to the specified torque.
Torque : 50 N·m (5.1kgf·m/37 lb·ft)
11. Install the suspension crossmember.
12. Install the torsion bar.
Refer to Torsion Bar in Suspension section.
13. Install the front propeller shaft.
Refer to Front Propeller Shaft in this section.
14. Install the hub and disc assembly and adjust the bearing preload.
Refer to Front Hub and Disc in this section.
15. Install the wheel speed sensor of the antilock brake system.
16. Install the brake caliper. Tighten the bolt of the caliper bracket to the specified torque.
Torque : 226 N·m (23.0kgf·m/166 lb·ft)
17. Install the stone guard.
18. Install the tire and wheel.
19. Lower the vehicle, adjust the trim height.
Refer to Trim Height Adjustment in Front Alignment section.
20. Tighten the bolts and nuts of the lower control arm to the specified torque.
Refer to Lower Control Arm in Suspension section.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-38 FRONT WHEEL DRIVE
FRONT HUB AND DISC
(4×2 Except High Ride Suspension Model)
Disassembly
Refer to SECTION 3E “W HEELS AND TIRES” for wheel removal procedure.

RTW 34CLF000801
Disassembly Steps
1. Bolt
▲ 2. Brake caliper
▲ 3. Hub cap
4. Split pin
5. Nut retainer
6. Hub nut
7. Lock washer


8. Outer bearing
▲ 9. Hub and disc assembly
10. Oil seal
11. Inner bearing and outer race
12. ABS sensor rotor
▲ 13. Bolt
▲ 14. W heel pin



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-39
Important Operations
Before removal, jack up the front of vehicle and support frame
with jack stands.



2. Brake Caliper
(1) Remove the two bolts from the rear side of the knuckle arm, then remove the brake caliper, with the brake hose
attached.
(2) Use a wire etc., for attaching the brake caliper to the uppe
r
link.
Refer to the section Brake.




3. Hub Cap
W hen removing hub cap, exercise care so as not to scratch or
distort hub fitting face.





9. Hub and Disc Assembly
Using a brass bar to remove the outer bearing outer race (1),
oil seal, inner bearing and inner bearing outer race (2) from the
hug.





If necessary, replace the wheel pin in the following manner.

13. Bolt
14. Wheel Pin ; Front Hub
(1) Scribe mark on hub to disc before disassembly to insure proper assembly.
(2) Drive out the ABS sensor rotor using a metal bar and hammer through the two bolt holes.
• Discard the used ABS sensor rotor
Refer to the section Brake.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-41
Inspection and Repair
Make necessary correction or parts replacement if wear, damage or any other abnormal conditions are found
through inspection.
For inspection and servicing of disc caliper, and relative parts, and ABS parts, refer to section 5 Brakes.



• Hub
• Hub bearing
• Bearing outer race
• Disc
• Oil seal
• Knuckle spindle
• ABS sensor rotor
• Caliper



Visual Check
Check the following parts for wear, damage or other abnormal
conditions.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-42 FRONT WHEEL DRIVE
Reassembly

RTW 34CLF000901
Reassembly Steps
▲ 1. W heel pin
▲ 2. Bolt
▲ 3. ABS sensor rotor
▲ 4. Inner bearing and outer race
▲ 5. Oil seal
▲ 6. Hub and disc assembly
7. Outer bearing


8. Lock washer
▲ 9. Hub nut
10. Nut retainer
11. Split pin
▲ 12. Hub cap
13. Brake caliper
▲ 14. Bolt



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-43


Important Operations
1. Wheel Pin
(1) Place hub on a wood workbench or a block of wood, approx. 6” by 6” to protect the wheel stud ends and threads.
(2) Install wheel stud using a hammer.
Be sure wheel stud is started squarely and seats completely.



(3) Align index marks and install hub to disc.



2. Bolt
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
103 (10.5/76)


3. ABS sensor rotor
(1) Set a new ABS sensor rotor, if replacement is required.
(2) Install the ABS sensor rotor in the hub, using special tools.
Installer : 5-8840-2789-0
Grip : 5-8840-0007-0
Refer to the section Brake.


RTW 74CSH000201
4. Inner Bearing and Outer Race
5. Oil Seal
• Outer Bearing Outer Race
(1) Install the bearing outer race by driving into the hub.
Installer (Outer) : 5-8840-2852-0
Installer (Inner) : 9-8522-1270-0
Grip : 5-8840-0007-0


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-46 FRONT WHEEL DRIVE
FRONT HUB AND DISC
(4×4, 4×2 High Ride Suspension, 4×4 Rigid Hub, 4×4 Shift On the Fly Model)
Disassembly
Refer to SECTION 3E “WHEELS AND TIRES” for wheel removal procedure
411R300011

Disassembly Steps
1. Bolt
2. Hub cap
3. Snap ring and shim (4×4 model only)
4. Flange (4×4 model only)
5. Lock washer
▲ 6. Hub nut
▲ 7. Hub and disc assembly


8. Outer bearing
9. Oil seal
10. Inner bearing
11. ABS sensor rotor
▲ 12. Bolt
▲ 13. W heel pin



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007