2007 ISUZU KB P190 lock

ELECTRICAL-BODY AND CHASSIS 8A-237


RUW 580SH000801
3. Turn the blade of the screwdriver 90 degrees to separate
the parts (1).



RUW 580SH000901
4. Use an ordinary screwdriver inserted into the inner groove
(1) of the outside mirror case to pry off the outside panel (it
pasts up on butyl tape). Do this at 5 points around the
groove.



RUW 580SH001001
5. Insert an ordinary screwdriver into the inner groove (1) of
the door mirror - turn signal light. Pry the light free.
6. Disconnect the connector (2).





Installation
Follow the removal procedure in the reverse order to install the
door mirror - turn signal light.
Pay close attention to the important points mentioned in the
following paragraphs.

SIDE TURN LIGHT
Removal
1. Remove the lens 1.
• Pull the light/bulb toward you while pushing the light
housing in the rear direction of the vehicle to release its
lock.
• Remove the socket by turning it counterclockwise.
2. Pull the bulb
2 to remove it.


Installation
Follow the removal procedure in the reverse order to install the
side turn light.
Pay close attention to the important points mentioned in the
following paragraphs.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-238 ELECTRICAL-BODY AND CHASSIS

Bulb
Be absolutely sure that the side turn light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.




A Type
RTW 780SH002101















REAR COMBINATION LIGHT
Turn Signal Light
Removal
1. Open the tail gate.
2. Remove the screws.
3. Remove the rear combination light assembly.



B Type
RTW 580SH000401



A Type
RTW 780SH001301

4. Turn the bulb 1 counterclockwise to remove it.




B Type
RTW 78ASH002501

Installation
Follow the removal procedure in the reverse order to install the
rear combination light.
Pay close attention to the important points mentioned in the
following paragraphs.

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-240 ELECTRICAL-BODY AND CHASSIS


B Type
RTW 580SH000401



A Type
RTW 780SH001401

4. Turn the bulb 1 counterclockwise to remove it.




B Type
RTW 78ASH002601



Installation
Follow the removal procedure in the reverse order to install the
rear combination light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulbs
Be absolutely sure that each bulb is correctly installed.
This will prevent a poor contact and an open circuit.




RTW 780SH001501
This illustration is based on RHD model

HAZARD WARNING FLASHER SWITCH
Removal
1. Disconnect the battery ground cable.
2. Instrument Panel Cluster Assembly • Refer to Section 10 “BODY” for instrument panel cluste
r
assembly removal steps.
3. Hazard W arning Switch • Disconnect the switch connector.
• To remove the switch, push the lock from the back side
of the cluster assembly.

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-242 ELECTRICAL-BODY AND CHASSIS

HORN SWITCH
Removal
1. Disable the SRS (Refer to “Disabling the SRS” in Section
9A).
2. Insertion hole for pin push bar at below the steering wheel indicated arrow.




RTW 78ASH001901
3. Check the position of the pins in the holes before insert the
pin push bar. Push the pin in the direction of the arrow.

4. Push the four pins using the φ5 ∼6 bar for cancel the lock on
the four pins.


RTW 78ASH002201
5. Disconnect the SRS air bag connector 1 and horn lead
connector
2 and remove the air bag assembly.
6. Remove the horn switch.




RTW 78ASH002401
Installation
1. Connect the SRS bag connector and horn lead connector.
2. Align each snap stud of the driver air bag to the hole in the steering wheel.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-261

DOOR SWITCH
Removal
1. Disconnect the battery ground cable.
2. Loosen the screw
1.
3. Remove the door switch
2.
4. Disconnect the door switch connector
3.





Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the door switch connector is securely
connected.
This will prevent a poor contact and an open circuit.


SPOTLIGHT (MAP Light)
Removal
1. Grasp the spotlight housing 1 with both hands.
Pull the housing straight down.
This will release the clip.
2. Disconnect the connector
2.
3. Turn socket
3 counterclockwise to remove it.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-262 ELECTRICAL-BODY AND CHASSIS



Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the spot light connector is securely
connected.
This will prevent a poor contact and an open circuit.



Bulb
Be absolutely sure that the spot light bulb is correctly installed.
This will prevent a poor contact and an open circuit.





RUW 580SH001501



RUW 580SH001601

OVER HEAD CONSOLE (MAP Light)
Removal
1. Open the lid (1) and remove the fastener (2).
2. A steel scale equivalent article is inserted in a lens side hook part and the crevice A section with roof lining, a metal
clip (5) is pushed in, and a over head consol (3) is removed
3. Disconnect the connector.
4. Push the bulb socket (4) in and turn it counterclockwise to remove it.







Installation
Follow the removal procedure in the reverse order to install the
front map light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the front map light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-263
INSPECTION AND REPAIR



R9 R10

R1 R6





DOOR SWITCH
Door Switch Connections
Connector
SW No.
R9
R10

R1 R6
position Terminal No.
1 Body Ground
PUSHED
RELEASED

W arning function Operational conditions
Key left in starter switch The buzzer sounds when both the key remind switch and the front door
switch-driver side are turned on.
To stop the sound of the buzzer, turn OFF the starter switch and remove the
key from the starter switch.
Lighting switch left on The buzzer sounds when the starter switch is turned from the “ON” to “OFF”
position while the lighting switch is ON position.
To stop the sound of the buzzer, turn OFF the lighting switch.


B62 B63


KEY REMIND SWITCH (STARTER
SWITCH)
Switch Connections
Connector
No. B63
Starter Terminal

switch key position No.
2 4
Removed

OFF

ACC Inserted
ON
START
LOCK




BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-386 ELECTRICAL-BODY AND CHASSIS
POWER DOOR LOCK
PARTS LOCATION (RHD)







RTW 78AXF039301 & RTW 78AXF045501

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007