2007 Hyundai Coupe headlight bulb

1FEATURES OF YOUR HYUNDAI
56MULTI-FUNCITION LIGHT SWITCH
B340A01A-AAT Combination Turn Signal, Headlight and High-beamSwitchTurn Signal Operation Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the levercauses the turn signals on the right side of the car to blink. As the turn is completed, the lever will automaticallyreturn to the center position and turn off the turn signals at the same time. If either turn signal indicator light blinksmore rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system.Check for a burned-out fuse or bulb or see your Hyundai dealer. B340B01A-AAT Lane Change Signal To indicate a lane change, move the lever up or down to a point where it begins flashing.The lever will automatically return to the center position when released.
B340C03E-AAT Headlight Switch To operate the headlights, turn the bar- rel on the end of the multi-function switch. The first position turns on theparking lights, sidelights, tail lights and instrument panel lights. The second position turns on the headlights. NOTE: The ignition must be in the "ON" position to turn on the headlights. Parking light auto cut (If installed)
o The purpose of this feature is to
prevent the battery from being dis- charged.
HGK2079
HGK2074

Engine Compartment .................................................... 6-2
General Checks ........................................................... 6-5
Checking the Engine Oil .............................................. 6-6
Checking and Changing the Engine Coolant ............... 6-9
Changing the Air Cleaner Filter ...................................6-11
Checking the Transaxle Oil (Manual) ......................... 6-15
Checking the Transaxle Fluid (Automatic) .................6-15
Checking the Brakes .................................................. 6-17
Checking the Clutch Fluid ........................................... 6-18
Air Conditioning Care .................................................. 6-18
Changing the Climate Control Air Filter .. ....................6-19
Checking and Replacing Fuses ..................................6-21
Checking the Battery .................................................. 6-23
Checking Electric Cooling Fans .................................6-24
Power Steering Fluid Level ......................................... 6-25
Headlight Aiming Adjustment ...................................... 6-26
Replacement of Light Bulbs ........................................6-27
Bulb Wattage ............................................................... 6-36
Fuse Panel D escription ............................................... 6-37
DO-IT-YOURSELF MAINTENANCE
6
6

6
DO-IT-YOURSELF MAINTENANCE
27
G290B02GK-GAT
Adjustment After Headlight As- sembly Replacement
If the vehicle has had front body repair and the headlight assembly has been replaced, the headlight aiming should be checked using an aiming screen asshown in the illustration. Turn on the headlight switch.
1. Adjust headlights so that main axis of light is parallel to center line of the body and is aligned with point"P" shown in the illustration.
2. Dotted lines in the illustration show the center of headlights. SPECIFICATION:
"H" Horizontal center line of headlights
from ground:
Low Beam: 690 mm (27.2 in.) High Beam: 674 mm (26.5 in.) "W" Distance between each headlight cen-
ter :
Low Beam: 1,336 mm (52.6 in.) High Beam: 1,098 mm (43.2 in.) "L" Distance between the headlights and
the wall that the lights are tested against : 3,000 mm (118 in.)
G290B01HR-1
H
Ground line
30mm (1.18 in.)
L
Cut-off line "P"
Horizontal line
H
W
Vertical line
REPLACEMENT OF LIGHT BULBS
G260A01MC-AAT Before attempting to replace a light
bulb, be sure the switch is turned to the "OFF" position.
The next paragraph shows how to
reach the light bulbs so they may bechanged. Be sure to replace the burned- out bulb with one of the same number and wattage rating.
See page 6-36 for the wattage descrip-
tions.
CAUTION:
o Keep the lamps out of contact with petroleum products, such asoil, gasoline, etc.
o If you don't have necessary tools, the correct bulbs and the exper- tise, consult your authorized Hyundai dealer.
!

6 DO-IT-YOURSELF MAINTENANCE
28
OGK076048
8. Remove the protective cap from
the replacement bulb and install the new bulb by matching the plas-
G270A01GK-AAT
Headlight and Front Turn Signal Light
1. Allow the bulb to cool. Wear eye
protection.
2. Open the engine hood.
3. Always grasp the bulb by its plastic base, avoid touching the glass.
OGK076047
5. Turn the plastic cover counterclock- wise and remove it.
4. Disconnect the power cord from the bulb base in the back of the head- light. OGK076066N
6. Disconnect the connector from thebulb base in the back of the head- light. 7. Push the bulb spring to remove the
headlight bulb.
OGK076050
OGK076049

6
DO-IT-YOURSELF MAINTENANCE
29
!WARNING:
This halogen bulb contains gas under pressure and if impacted could shatter, resulting in flying fragments. Always wear eye pro-tection when servicing the bulb. Protect the bulb against abrasions or scratches and against liquidswhen lighted. Turn the bulb on only when installing in a head- light. Replace the headlight if dam-aged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb with care.
11. To replace the front turn signal light
bulb, remove from the bulb holderand install the new bulb. OGK076052
tic base with the headlight hole.Reattach the bulb spring and re-connect the connector.
9. Use the protective cap and carton
to promptly dispose of the old bulb.
10.Check for proper headlight aim.
G270A03OG270B01GK-GAT Rear Combination Light (Without woofer speaker)
1. Open the tail gate. OGK076037
(1)
(2)
(3)
G270K01CM-GAT Front Fog Light (If Installed) NOTE: It is recommended that the front fog light bulb be replaced by an autho- rized Hyundai dealer.
(1)

6
Engine Compartment .................................................... 6-2
Daily Operating Checks ............................................... 6-5
Maintenance Precautions ............................................. 6-5
Engine Oil ..................................................................... 6-6
Engine Coolant Checking and Replacing .................... 6-9
Changing the Air Cleaner Filter ...................................6-11
Manual Transaxle Lubricant .................... ....................6-14
Automatic Transaxle Fluid ........................................... 6-14
Brake System Checking ............................................. 6-16
Checking the Clutch Fluid ........................................... 6-17
Air Conditioning System Maintenance ........................ 6-17
Changing the Climate Control Air Filter .. ....................6-18
Fusible Links ............................................................... 6-20
Battery Mai ntenance ................................................... 6-21
Electric Cooling Fans .................................................. 6-23
Power Steering Fluid Level ......................................... 6-23
Headlight Aiming Adjustment ...................................... 6-24
Replacing Light Bulbs ................................................. 6-25
Bulb Wattage ............................................................... 6-33
Fuse Panel D escription ............................................... 6-34
OWNER MAINTENANCE
6

6
OWNER MAINTENANCE
25
SPECIFICATION: "H" Horizontal centre line of headlights from ground: Low Beam: 27.2 in. (690 mm) High Beam: 26.5 in. (674 mm) "W" Distance between each headlight cen- tre : Low Beam: 52.6 in. (1,336 mm) High Beam: 43.2 in. (1,098 mm) "L" Distance between the headlights and the wall that the lights are tested against : 118.11 in. (3,000 mm)REPLACING LIGHT BULBS
G260A01MC-EAT In the event of bulb failure being expe-
rienced, ensure that the relative light- ing circuit is turned off prior to attempt-ing to replace the bulb. The illustra- tions on the following page will assist in locating and removing the various
bulbs. Ensure that the replacement bulb has the same cap configuration and wattage as the original.
See page 6-33 for the wattage descrip-
tions.
CAUTION:
o Keep the lamps out of contact with petroleum products, such as oil, petrol, etc.
o If you don't have necessary tools, the correct bulbs and the exper- tise, consult your Hyundaiauthorised repairer.
!
G270A01GK-EAT
Headlight and Front Turn Signal Light
1. Allow the bulb to cool. Wear eye
protection.
2. Open the engine bonnet.
3. Always grasp the bulb by its plastic base, avoid touching the glass.
4. Disconnect the power cord from the
bulb base in the back of the head- light. OGK076066N

6OWNER MAINTENANCE
26
8. Remove the protective cap from
the replacement bulb and install the new bulb by matching the plas- tic base with the headlight hole.Reattach the bulb spring and re- connect the connector.
9. Use the protective cap and carton to promptly dispose of the old bulb.
10.Check for proper headlight aim.
7. Push the bulb spring to remove the
headlight bulb.
OGK076050OGK076049
OGK076048
OGK076047
5. Turn the plastic cover counterclock- wise and remove it.
6. Disconnect the connector from the bulb base in the back of the head- light.