2007 HUMMER H3 radio

tSEEKu:Press and release the right or the
left arrow to go to the next or to the previous
station and stay there.
The radio only seeks stations with a strong
signal that are in the selected band.
Press and hold either arrow for more than
two seconds. SCAN displays and the radio
produces one beep. The radio goes to a station,
plays for a few seconds, then goes to the next
station. Press either arrow again or one of
the pushbuttons to stop scanning presets.
The radio only scans stations with a strong
signal that are in the selected band.
Press and hold this button until PSCN displays
and the radio produces two beeps. The radio
goes to a preset station, plays for a few seconds,
then goes to the next preset station. Press
either arrow again or one of the pushbuttons
to stop scanning presets.
The radio only scans preset stations with a strong
signal that are in the selected band.4(Information) (XM™ Satellite Radio Service):
If the current station has a message, the information
symbol appears on the display. Press this button to
see the message. The message may display the
artist, song title, call in phone numbers, etc.
If the entire message is not displayed, parts of the
message appears every three seconds. To scroll
through the message, press and release the
INFO button. A new group of words appears on the
display after every press of this button. Once the
complete message has displayed, the information
symbol disappears from the display until another
new message is received. The last message can
be displayed by pressing the INFO button. You
can view the last message until a new message
is received or a different station is tuned to.
When a message is not available from a station,
No Info displays.
1-6 (Preset Pushbuttons):Press this button
to play stations that are programmed on the
radio preset pushbuttons.
The radio only seeks preset stations with a
strong signal that are in the selected band.
213

Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be
programmed on the six numbered pushbuttons,
by performing the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM,
or XM1 or XM2.
3. Tune in the desired station.
4. Press AUTO EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until a beep sounds. Whenever
that numbered pushbutton is pressed,
the station that was set returns and the
equalization that was selected is stored for
that pushbutton.
6. Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
e
(Bass/Treble):Push and release this knob
until BASS or TREB displays. Turn this knob
to increase or to decrease. The display shows the
bass or the treble level. If a station is weak or
has static, decrease the treble.
To adjust the bass and the treble to the middle
position, while in bass or treble, push and hold the
tone knob. The radio produces one beep.
To adjust all tone and speaker controls to the
middle position, push and hold the tone knob
when no tone or speaker control is displayed.
ALL CENTERED displays and a beep sounds.
AUTO EQ (Automatic Equalization):Press this
button to select customized equalization settings
designed for country/western, jazz, talk, pop,
rock and classical.
The equalization one through seven options are
included only if your vehicle is equipped with
the Bose
®system. Press the AUTO EQ button
to select equalization settings designed for
equalization one through seven.
To return the bass and treble to the manual mode,
push and release the tone knob until BASS and
TREB displays.
214

Adjusting the Speakers (Balance/Fade)
e
(Balance/Fade):To adjust the balance
between the right and the left speakers, push and
release this knob until BAL displays. Turn the
knob to move the sound toward the right or the
left speakers.
To adjust the fade between the front and the rear
speakers, push and release the tone knob until
FADE displays. Turn the knob to move the sound
toward the front or the rear speakers.
To adjust the balance and the fade to the
middle position, push the tone knob, then push
it again and hold it until one beep sounds.
To adjust all tone and speaker controls to the
middle position, while in fade or balance, push
and hold the tone knob when no tone or speaker
control is displayed. ALL CENTERED displays
and a beep sounds.
Finding a Category (CAT) Station
(XM™ Satellite Radio Service Only)
To select and nd a desired category perform
the following:
1. Press the CAT button to activate category
select mode. The current category appears
on the display.
2. Turn the tune knob to select a category.
3. Once the desired category is displayed,
press either SEEK arrow to take you to
that category’s rst station.
4. To go to another station within that category
and the category is displayed, press either
SEEK arrow again. If CAT times out and is
no longer on the display, go back to Step 1.
5. Press CAT to exit category select mode or
wait for CAT to time out.
If the radio cannot nd the desired category,
NOT FOUND displays and the radio returns to
the last station you were listening to.
215

Radio Messages
CAL ERR (Calibration Error):The audio system
has been calibrated for your vehicle from the
factory. If CAL ERR displays it means that
the radio has not been congured properly for
your vehicle and it must be returned to your
dealer for service.
LOC (Locked):This message is displayed
when the THEFTLOCK
®system has locked up.
Take your vehicle to your dealer for service.
If any error occurs repeatedly or if an error cannot
be corrected, contact your dealer.
Radio Messages for XM™ Only
SeeXM Radio Messages on page 228later in
this section for further detail.
Playing a CD
If the ignition or radio is turned off, with a CD in the
player, it stays in the player. When the ignition or
radio is turned on, the CD starts playing where it
stopped, if it was the last selected audio source.When a CD is inserted, READING and the CD
symbol appears on display. As each new
track starts to play, the track number appears
on the display.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
If playing a CD-R, the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There may be an increase in skipping,
difficulty in nding tracks, and/or difficulty in loading
and ejecting. If these problems occur, check the
bottom surface of the CD. If the surface of the CD
is damaged, such as cracked, broken, or
scratched, the CD will not play properly. If the
surface of the CD is soiled, seeCare of Your CDs
on page 231for more information.
If there is no apparent damage, try a known
good CD.
216

Do not add any label to a CD, it could get caught
in the CD player. If a CD is recorded on a
personal computer and a description label is
needed, try labeling the top of the recorded CD
with a marking pen.
Notice:If you add any label to a CD, insert
more than one CD into the slot at a time, or
attempt to play scratched or damaged CDs,
you could damage the CD player. When using
the CD player, use only CDs in good condition
without any label, load one CD at a time, and
keep the CD player and the loading slot free
of foreign materials, liquids, and debris.
If an error appears on the display, see
“CD Messages” later in this section.
LOAD:Press this button to load CDs into the
CD player. This CD player holds up to six CDs.
To insert one CD, do the following:
1. Turn the ignition on.
2. Press and release the LOAD button.
3. Wait for the indicator light, located to the
right of the slot, to turn green.
4. Load a CD. Insert the CD partway into the slot,
label side up. The player pulls the CD in.To insert multiple CDs, do the following:
1. Turn the ignition on.
2. Press and hold the LOAD button for
two seconds.
A beep will sound and the indicator light,
located to the right of the slot, begins to ash
and LOAD # displays.
3. Once the light stops ashing and turns green,
INSERT CD # displays, load a CD. Insert the
CD partway into the slot, label side up.
The player pulls the CD in.
Once the CD is loaded, the indicator light
begins ashing again. Once the light stops
ashing and turns green, you can load another
CD. The CD player takes up to six CDs.
Do not try to load more than six.
To load more than one CD but less than six,
complete Steps 1 through 3. When nished
loading CDs, press the LOAD button to cancel
the loading function. The radio begins to play
the last CD loaded.
If more than one CD has been loaded, a number
for each CD displays.
217

To use repeat, do the following:
To repeat the track you are listening to, press
and release the repeat button. RPT ON
displays. Press this button again to turn off
repeat play. RPT OFF displays.
To repeat the CD you are listening to, press
and hold the repeat button for two seconds.
RPT ON displays. Press this button again
to turn off repeat play. RPT OFF displays.
y(Random):With random, you can listen to the
tracks in random, rather than sequential, order,
on one CD or on all of the CDs. To use random,
do one of the following:
To play the tracks on the CD you are listening
to in random order, press and release the
random button. RANDOM ONE displays.
Press this button again to turn off random play.
To play the tracks on all of the CDs that
are loaded in random order, press and
hold this button for more than two seconds.
A beep sounds and RANDOM ALL displays.
Press this button again to turn off random play.
tSEEKu:Press the left arrow to go to the
start of the current track, if more than ten seconds
have played. Press the right arrow to go to the
next track. If either arrow is held or pressed more
than once, the player continues moving backward
or forward through the CD.
To scan one CD, press and hold either arrow for
more than two seconds until SCAN displays
and a beep sounds. The radio goes to the next
track, plays for 10 seconds, then goes to the next
track. Press either arrow again, to stop scanning.
To scan all loaded CDs, press and hold either arrow
for more than four seconds until CD SCAN displays
and a beep sounds. Use this feature to listen to
10 seconds of the rst track of each loaded CD.
Press either arrow again, to stop scanning.
DISP (Display):Press this knob to see how long
the current track has been playing. The elapsed
time of the track appears on the display. To
change the default on the display, track or elapsed
time, press this knob until you see the desired
display, then hold the knob for two seconds.
The radio produces one beep and the selected
display becomes the default.
219

BAND:Press this button to listen to the radio
when a CD is playing. The inactive CD(s) remains
safely inside the radio for future listening.
B(CD):Press this button to play a CD while
listening to the radio. The CD symbol appears on
the display when a CD is loaded.
AUTO EQ (Automatic Equalization):Press
AUTO EQ to select an equalization setting while
playing a CD. The equalization is set whenever a
CD is played. See “AUTO EQ” listed previously for
more information. If you select an EQ setting for
your CD, it is activated each time you play a CD.
Using Song List Mode
R
(Song List):The six-disc CD changer has a
feature called song list. This feature is capable
of saving 20 track selections.
To save tracks into the song list feature, perform
the following steps:
1. Turn the CD player on and load it with at least
one CD. See “LOAD CD” listed previously in
this section for more information.
2. Check to see that the CD changer is not in
song list mode. S-LIST should not appear on
the display. If S-LIST is present, press the
song list button to turn it off.3. Select the desired CD by pressing the
numbered pushbutton and then use the SEEK
SCAN right arrow to locate the track to be
saved. The track begins to play.
4. Press and hold the song list button to save
the track into memory. When the song list
button is pressed, one beep sounds. After
two seconds of continuously pressing the song
list button, two beeps sounds to conrm the
track has been saved.
5. Repeat Steps 3 and 4 for saving other
selections.
S-LIST FULL displays if you try to save more than
20 selections.
To play the song list, press the song list button.
One beep sounds and S-LIST displays. The
recorded tracks begins to play in the order they
were saved.
Seek through the song list by using the SEEK
SCAN arrows. Seeking past the last saved track
returns to the rst saved track.
220

CD Messages
CHECK CD:If this message appears on the
display and/or the CD comes out, it could be for
one of the following reasons:
It is very hot. When the temperature returns
to normal, the CD should play.
You are driving on a very rough road. When the
road becomes smoother, the CD should play.
The CD is dirty, scratched, wet, or
upside down.
The air is very humid. If so, wait about an
hour and try again.
There may have been a problem while
burning the CD.
The label may be caught in the CD player.
If the CD is not playing correctly, for any other
reason, try a known good CD.
If any error occurs repeatedly or if an error
cannot be corrected, contact your dealer. If the
radio displays an error message, write it down
and provide it to your dealer when reporting
the problem.
Using an MP3
MP3 CD-R Disc
MP3 Format
If you burn your own MP3 disc on a personal
computer:
Make sure the MP3 les are recorded on
a CD-R disc.
Do not mix standard audio and MP3 les
on one disc.
Make sure playlists have a .mp3 or .wpl
extension, other le extensions may not work.
Files can be recorded with a variety of xed or
variable bit rates. Song title, artist name, and
album are available for display by the radio
when recorded using ID3 tags version 1 and 2.
Create a folder structure that makes it easy to
nd songs while driving. Organize songs by
albums using one folder for each album. Each
folder or album should contain 18 songs or less.
Make sure to nalize the disc when burning an
MP3 disc, using multiple sessions. It is usually
better to burn the disc all at once.
222