2007 HUMMER H2 key battery

At times you may notice a decrease in operating
range. This is normal for any RKE system. If
the transmitter does not work or if you have to
stand closer to your vehicle for the transmitter to
work, try this:
Check the distance. You may be too far from
your vehicle. You may need to stand closer
during rainy or snowy weather.
Check the location. Other vehicles or objects
may be blocking the signal. Take a few steps
to the left or right, hold the transmitter
higher, and try again.
Check to determine if battery replacement is
necessary. See “Battery Replacement”
underRemote Keyless Entry (RKE) System
Operation on page 97.
If you are still having trouble, see your dealer
or a qualied technician for service.
Remote Keyless Entry (RKE)
System Operation
You can lock and unlock your doors from about
3 feet (1 m) up to 100 feet (30 m) away using the
Remote Keyless Entry (RKE) transmitter
supplied with your vehicle.
K(Unlock):Press this
button once to unlock
the driver’s door.
The interior lamps will
come on. Pressing
unlock again within
three seconds will cause
the remaining doors
to unlock.
You can choose different feedback options for
each press of the unlock button. See “Lock
Feedback” and “Unlock Feedback” underDIC
Vehicle Customization on page 234for more
information.
97

To replace the battery in the RKE transmitter, do
the following:
1. Insert a thin object, such as a coin, in the slot
between the covers of the transmitter housing
near the key ring hole. Remove the bottom
by twisting the coin.
2. Remove and replace the battery with a
three-volt CR2032 or equivalent battery,
positive (+) side up.3. Align the covers and snap them together.
4. Resynchronize the transmitter. See
“Resynchronization” following this information.
5. Check the operation of the transmitter.
Resynchronization
Resynchronization may be necessary due to the
security method used by this system. The
transmitter does not send the same signal twice to
the receiver. The receiver will not respond to a
signal that has been sent previously. This prevents
anyone from recording and playing back the
signal from the transmitter.
To resynchronize your transmitter, stand close to
your vehicle and press and hold the lock and
unlock buttons on the transmitter at the same time
for 15 seconds. The door locks should cycle to
conrm synchronization. If the locks do not cycle,
see your dealer for service.
99

Content Theft-Deterrent
Your vehicle is equipped with a content
theft-deterrent alarm system.
With this system, the
security light in the
instrument panel cluster
will ash as you open
the door if your
ignition is off.
This light reminds you to activate the
theft-deterrent system. Here is how to do it:
1. Open the door.
2. Lock the door with the power door lock switch
or the remote keyless entry transmitter. The
security light will illuminate to inform the driver
the system is arming. If a door is open when
the doors are locked, the security light
will ash.3. Close all doors. The security light should go
off after about 30 seconds. The alarm is not
armed until the security light goes off.
If the delayed locking feature is turned on,
the theft-deterrent system will not start
the arming process until the last door is
closed and the delay timer has expired.
SeeDelayed Locking on page 102.
If a locked door is opened without the key or
the remote keyless entry transmitter, the alarm will
go off. The headlamps and parking lamps will
ash for two minutes, and the horn will sound for
30 seconds, then will turn off to save the battery
power. You can choose different feedback options
for the alarm. SeeDIC Vehicle Customization
on page 234.
Remember, the theft-deterrent system will not
activate if you lock the doors with the vehicle’s key
or use the manual door lock. It activates only if
you use a power door lock switch with the
door open, or with the remote keyless entry
transmitter. You should also remember that you
can start your vehicle with the correct ignition key if
the alarm has been set off.
116

Ignition Positions
Use the key to turn the ignition switch to
four different positions.
A (LOCK):This position locks the ignition and
transmission. It is a theft-deterrent feature. You will
only be able to remove the key when the ignition
is turned to LOCK.Notice:Using a tool to force the key from the
ignition switch could cause damage or break
the key. Use the correct key and turn the key
only with your hand. Make sure the key is all the
way in. If it is, turn the steering wheel left and
right while you turn the key hard. If none of this
works, then your vehicle needs service.
B (ACCESSORY):This position lets you use
things like the radio and the windshield wipers
when the engine is off.
Lengthy operation of features such as the radio in
the accessory ignition position and the RUN
position may drain the battery and prevent your
vehicle from starting. Do not operate your vehicle
in the accessory ignition position for a long
period of time.
C (RUN):This is the position for driving. It is the
position the switch returns to after the engine
starts, and you release the key.
The battery could be drained if you leave the key
in the ACCESSORY or RUN position with the
engine off. You may not be able to start your
vehicle if the battery is allowed to drain for
an extended period of time.
D (START):This position starts the engine.
120

Key In the Ignition
Never leave your vehicle with the keys inside, as it
is an easy target for joy riders or thieves. If you
leave the key in the ignition and park your vehicle,
a chime will sound, when you open the driver’s
door. Always remember to remove your key from
the ignition and take it with you. This will lock
your ignition and transmission. Also, always
remember to lock the doors.
The battery could be drained if you leave the key
in the ignition while your vehicle is parked.
You may not be able to start your vehicle after it
has been parked for an extended period of time.
Retained Accessory Power (RAP)
The Retained Accessory Power (RAP) feature will
allow certain features on your vehicle to continue to
work for up to 10 minutes after the ignition key is
turned to LOCK or until one of the doors is opened.
Starting the Engine
Place the transmission in the proper gear.
Move your shift lever to PARK (P) or
NEUTRAL (N). Your engine will not start in
any other position – this is a safety feature.
To restart when you are already moving, use
NEUTRAL (N) only.
Notice:Do not try to shift to PARK (P) if your
vehicle is moving. If you do, you could
damage the transmission. Shift to PARK (P)
only when your vehicle is stopped.
Starting Procedure
1. With your foot off the accelerator pedal, turn
the ignition key to START. When the engine
starts, let go of the key. The idle speed will go
down as your engine gets warm. Do not
race the engine immediately after starting it.
Operate the engine and transmission gently to
allow the oil to warm up and lubricate all
moving parts.
121

Your vehicle has a Computer-Controlled
Cranking System. This feature assists in
starting the engine and protects components. If
the ignition key is turned to the START position,
and then released when the engine begins
cranking, the engine will continue cranking for a
few seconds or until the vehicle starts. If the
engine does not start and the key is held in
START for many seconds, cranking will be
stopped after 15 seconds to prevent cranking
motor damage. To prevent gear damage, this
system also prevents cranking if the engine is
already running. Engine cranking can be
stopped by turning the ignition switch to the
ACCESSORY or LOCK position.
Notice:Cranking the engine for long periods
of time, by returning the key to the START
position immediately after cranking has ended,
can overheat and damage the cranking
motor, and drain the battery. Wait at least
15 seconds between each try, to allow
the cranking motor to cool down.2. If the engine does not start after 5-10 seconds,
especially in very cold weather (below 0°F
or−18°C), it could be ooded with too much
gasoline. Try pushing the accelerator
pedal all the way to the oor and holding it
there as you hold the key in START for up to
a maximum of 15 seconds. Wait at least
15 seconds between each try, to allow the
cranking motor to cool down. When the engine
starts, let go of the key and accelerator. If
the vehicle starts briey but then stops again,
do the same thing. This clears the extra
gasoline from the engine. Do not race the
engine immediately after starting it. Operate
the engine and transmission gently until the oil
warms up and lubricates all moving parts.
Notice:Your engine is designed to work with
the electronics in your vehicle. If you add
electrical parts or accessories, you could
change the way the engine operates. Before
adding electrical equipment, check with
your dealer. If you do not, your engine might
not perform properly. Any resulting damage
would not be covered by your vehicle’s
warranty.
122

Reading Lamps
Your vehicle has reading lamps located in the
overhead console. Press the button located next
to the lamp to turn it on. The lamps can be
adjusted to point in the direction you want.
Press the button again to turn the lamp off.
These lamps will also come on with the
dome lamps.
Battery Run-Down Protection
This feature shuts off the dome lamps if they are
left on for more than 10 minutes when the
ignition is in LOCK. This will help prevent the
battery from running down.
Rear Vision Camera
Your vehicle may be equipped with a rear vision
camera system. Read this entire section before
using the camera system.The rear vision camera system is designed to help
the driver when backing up by displaying a view
of the area behind the vehicle. When the
driver shifts the vehicle into REVERSE (R), the
video screen will automatically slide out from
the rear view mirror. Once the driver shifts out of
REVERSE (R), the video screen will slide back
into the rear view mirror after a delay.
To turn off the rear vision camera system, do the
following:
1. Place the vehicle shift lever in (P) PARK.
2. Turn the ignition key to the ACCESSORY
position.
3. Press the right mirror button briey; the right
green light indicator will turn off. The rear
camera vision display is now disabled.
To turn on the rear camera vision feature again,
press the right mirror button briey. The green light
indicator will illuminate. The rear camera vision
system is now enabled and the display will
slide out from the mirror normally.
192

ENGINE COOLANT HOT
This message displays if the cooling system
temperature gets hot. Turn off the air conditioning.
If the message is still on, or if the engine coolant
temperature gage continues to rise, pull the vehicle
over when it is safe to do so. SeeEngine
Coolant Temperature Gage on page 213for more
information. Stop the vehicle and let the engine
idle in PARK (P) for a few minutes to allow
the coolant to reach a safe temperature. This
message clears when the coolant temperature
drops to a safe operating temperature. Press any
of the DIC buttons, or the trip stem, to
acknowledge this message and clear it from the
DIC display.
ENGINE OVERHEATED
This message displays and a chime sounds if the
engine cooling system reaches unsafe
temperatures for operation. Stop and turn off the
vehicle as soon as it is safe to do so to avoid
severe damage. This message clears when the
engine has cooled to a safe operating temperature.
FUEL LEVEL LOW
This message displays and a chime sounds if the
fuel level is low. Refuel as soon as possible.
Press any of the DIC buttons, or the trip stem, to
acknowledge this message and clear it from
the DIC display. This message also clears itself
after 10 seconds. The low fuel light near the
fuel gage still remains on in either case. SeeLow
Fuel Warning Light on page 221,Fuel Gage on
page 221, andFuel on page 394for more
information.
KEYFOB X BATTERY LOW
This message displays if a Remote Keyless
Entry (RKE) transmitter battery is low. Replace
the battery in the transmitter. See “Battery
Replacement” underRemote Keyless Entry (RKE)
System Operation on page 97. Press any of the
DIC buttons, or the trip stem, to acknowledge this
message and clear it from the DIC display.
228