2007 HUMMER H2 battery replacement

At times you may notice a decrease in operating
range. This is normal for any RKE system. If
the transmitter does not work or if you have to
stand closer to your vehicle for the transmitter to
work, try this:
Check the distance. You may be too far from
your vehicle. You may need to stand closer
during rainy or snowy weather.
Check the location. Other vehicles or objects
may be blocking the signal. Take a few steps
to the left or right, hold the transmitter
higher, and try again.
Check to determine if battery replacement is
necessary. See “Battery Replacement”
underRemote Keyless Entry (RKE) System
Operation on page 97.
If you are still having trouble, see your dealer
or a qualied technician for service.
Remote Keyless Entry (RKE)
System Operation
You can lock and unlock your doors from about
3 feet (1 m) up to 100 feet (30 m) away using the
Remote Keyless Entry (RKE) transmitter
supplied with your vehicle.
K(Unlock):Press this
button once to unlock
the driver’s door.
The interior lamps will
come on. Pressing
unlock again within
three seconds will cause
the remaining doors
to unlock.
You can choose different feedback options for
each press of the unlock button. See “Lock
Feedback” and “Unlock Feedback” underDIC
Vehicle Customization on page 234for more
information.
97

Q(Lock):Press this button once to lock all of the
doors. Pressing lock again within three seconds
may cause the horn to chirp for lock conrmation.
You can choose different feedback options for each
press of the lock button. See “Lock Feedback” and
“Unlock Feedback” underDIC Vehicle
Customization on page 234for more information.
L(Panic):Press this button to sound the horn
and ash the headlamps and taillamps for up
to 30 seconds. Panic can be turned off by pressing
the button again, by waiting for 30 seconds, or
by starting the vehicle.
Matching Transmitter(s) to Your Vehicle
Each RKE transmitter is coded to prevent another
transmitter from unlocking your vehicle. If a
transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring
any remaining transmitters with you when you go to
your dealer. When the dealer matches the
replacement transmitter to your vehicle, any
remaining transmitters must also be matched. Once
your dealer has coded the new transmitter, the lost
transmitter will not unlock your vehicle. Each
vehicle can have a maximum of four transmitters
matched to it.
Battery Replacement
Under normal use, the battery in your
RKE transmitter should last about two years.
You can tell the battery is weak if the transmitter
will not work at the normal range in any location.
If you have to get close to your vehicle before the
transmitter works, it is probably time to change
the battery.
Notice:When replacing the battery, use
care not to touch any of the circuitry. Static
from your body transferred to these surfaces
may damage the transmitter.
98

ENGINE COOLANT HOT
This message displays if the cooling system
temperature gets hot. Turn off the air conditioning.
If the message is still on, or if the engine coolant
temperature gage continues to rise, pull the vehicle
over when it is safe to do so. SeeEngine
Coolant Temperature Gage on page 213for more
information. Stop the vehicle and let the engine
idle in PARK (P) for a few minutes to allow
the coolant to reach a safe temperature. This
message clears when the coolant temperature
drops to a safe operating temperature. Press any
of the DIC buttons, or the trip stem, to
acknowledge this message and clear it from the
DIC display.
ENGINE OVERHEATED
This message displays and a chime sounds if the
engine cooling system reaches unsafe
temperatures for operation. Stop and turn off the
vehicle as soon as it is safe to do so to avoid
severe damage. This message clears when the
engine has cooled to a safe operating temperature.
FUEL LEVEL LOW
This message displays and a chime sounds if the
fuel level is low. Refuel as soon as possible.
Press any of the DIC buttons, or the trip stem, to
acknowledge this message and clear it from
the DIC display. This message also clears itself
after 10 seconds. The low fuel light near the
fuel gage still remains on in either case. SeeLow
Fuel Warning Light on page 221,Fuel Gage on
page 221, andFuel on page 394for more
information.
KEYFOB X BATTERY LOW
This message displays if a Remote Keyless
Entry (RKE) transmitter battery is low. Replace
the battery in the transmitter. See “Battery
Replacement” underRemote Keyless Entry (RKE)
System Operation on page 97. Press any of the
DIC buttons, or the trip stem, to acknowledge this
message and clear it from the DIC display.
228

Headphones
Wireless Headphones
The RSE system might include two sets of
wireless headphones. Each headphone has an
L marked on the left-side, for the left ear and an
R marked on the right-side, for the right ear. The
L and R marks are to show how the headphones
should be worn.
OFF/ON (Power):The wireless headphones have
an OFF/ON power switch located on the
earpiece. To use the headphones, turn the switch
to ON. An indicator light on the earpiece of the
headphones illuminates. If the light does not
illuminate, the batteries might need to be replaced.
See “Battery Replacement” later in this section.
Switch the headphones to OFF when not in use.
The headphones shut off automatically to save the
battery power if the RSE system is shut off or if
the headphones are out of range of the transmitter
window for more than three minutes. The
transmitter window is located on the bottom edge
of the monitor. If you move too far forward or
step out of the vehicle, the headphones could lose
the audio signal.Channel Selector:The wireless headphones
have a channel selector switch located on the right
earpiece. The channel selector switches between
Channel A and Channel B. Since each monitor
can function as two independent sources through
auxiliary input, it is necessary to transmit audio
signals on separate channels. The driver’s
side monitor is designated as Channel A, and the
passenger’s side as Channel B. The Headphone
channel selector switch must be set to the
correct channel according to the monitor being
viewed. When the head restraint monitor is initially
turned on, the message, “To listen to this
monitor tune your headphones to channel A
(or B)” displays for ve seconds then disappears.
VOL
0(Volume):To adjust the volume
on the wireless headphones, use the volume
control.
Notice:Do not store the headphones in heat
or direct sunlight. This could damage the
headphones and repairs will not be covered by
your warranty. Keep the headphones stored
in a cool, dry place.
272

If there is a decreased audio signal during CD,
MP3, or DVD play, there could be a soft hissing
noise through the speakers and/or headphones.
If the hissing sound in the wireless headphones
seem excessive, make sure the headphone
batteries are fully charged. A small amount of
hissing is normal.
Battery Replacement
To change the batteries, do the following:
1. Press down on the left earpiece and slide the
battery compartment panel down to expose
the battery compartment.
2. Replace the two AAA batteries in the
compartment. Make sure they are installed
correctly using the diagram on the inside
of the battery compartment.
3. Slide the battery compartment panel back and
then down until the panel closes into the
headphone ear piece.
If the headphones are to be stored for a long
period of time, remove the batteries, and keep
them in a cool, dry place.
Wired Headphones
There is a headphone jack on the left lower side
of the video screen. Use this jack with universal
wired headphones. To adjust the volume, do
the following:
1. Press the power button on the monitor to turn
the video screen on. Briey press the power
button again to toggle between monitor and
DVD control buttons. The appropriate toggle is
monitor. Main menu function icons display.
2. Plug the headphone into the corresponding
jack, located on the bottom left of the video
screen, next to the auxiliary jack.
3. Press the soft key buttons on the monitor,
located under the up and down arrow icons,
to increase or to decrease the volume.
Audio Output
Audio from the DVD player or auxiliary devices
can be heard through the vehicle speakers or the
wireless/wired headphones. The FM Modulator
control has to be set to one of eight frequencies in
order for these devices to be heard through the
vehicle’s speakers. See “FM Modulator Control”
later in this section.
273

Remote Control
The system’s remote control combines the control
of all monitor and DVD player functions. To use
the system’s remote control, aim at the remote
sensor located on the upper right side of the
monitor and press the desired button on the
remote control. The remote works best when held
at a comfortable distance from the monitors.
Direct sunlight or very bright light can affect the
ability of the transmitter to receive signals from the
system’s remote control. If the remote control
does not seem to be working, the batteries might
need to be replaced. See “Battery Replacement”
later in this section. Objects blocking the
line-of-sight affects the function of the system’s
remote control.
Notice:Storing the remote control in a hot
area or in direct sunlight may damage it,
and the repairs will not be covered by your
warranty. Keep the remote control stored in a
cool, dry place.
Remote Control Buttons
(Monitor Control Functions)
P(Power/Monitor):Press this button to turn
the monitor on and off.
PICTURE:Press this button to adjust the basic
monitor control functions such as: CONTRAST,
BRIGHTNESS, COLOR, TINT, RESET, MODE,
and SHARPNESS.
280

Battery Replacement
To change the remote control batteries, do the
following:
1. Slide the battery door, located on the back of
the remote control, down.
2. Replace the two AAA batteries in the
compartment. Make sure they are installed
correctly, using the diagram on the inside
of the battery compartment.
3. Close the battery door.
If the remote control is to be stored for a long
period of time, remove the batteries and keep them
in a cool, dry place.
Using the RSE On-Screen
Display (OSD) Menu
To use the RSE OSD menu while using the DVD
player or an auxiliary device, do the following:
1. Press the SETUP button on the system’s
remote control to access the general setup
menu, see “Remote Control” earlier in
this section.
2. Once this menu is on the screen, press the
directional arrows and then the ENTER
button to navigate the screen.
This menu lets you select default preferences
for language, video, audio, and ratings.
Not all DVDs support all of the feature defaults
in the setup menus. If a feature is not
supported, the defaults are provided by the
DVD media.
The default language selection applies to all
future DVDs.
3. Press the RETURN button on the system’s
remote control to exit this menu, or wait for
the menu to time out.
284

This harness may be included with your vehicle as
part of the heavy-duty trailer wiring package.
{CAUTION:
Be sure to use only the correct trailer
brake harness, the one intended for use
on your vehicle. If you use some other
trailer brake harness, even if it seems to
t, your trailer brakes may not work at all.
You could have a crash in which you or
others could be injured. Use only the
trailer brake harness intended for your
vehicle. If it is no longer available to you,
be sure to get a proper replacement from
your dealer.
This harness is for an electric brake controller and
includes a trailer battery feed fuse. It should be
installed by your dealer or a qualied service
center.
387