2007 HONDA PILOT remote control

If it takes several pushes on the
button to operate the rear
entertainment system, have your
dealer replace the batteries as soon
as possible.
The rear control panel can be
detached f rom the ceiling unit and
used as a remote control. To remove
it f rom the ceiling unit, press the
release button. The control panel will
swing down partway. Pivot it down
f urther past the detent until it
detaches f rom the hinge. To reinstall
it, reverse the procedure.
Battery type: BR3032
As required by the FCC: This device
complies with Part 15 of the FCC rules.Operation is subject to the f ollowing twoconditions: (1) This device may notcause harmf ul interf erence, and (2) thisdevice must accept any interf erencereceived, including interf erence thatmay cause undesired operation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210. Operation issubject to the f ollowing two conditions:(1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.Remote Control Replacing the Remote Control
Batteries
Rear Entertainment System
Features
169
COVER
RELEASE BUTTON

µ
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected. The HomeLinkuniversal
transceiver built into your vehicle
canbeprogrammedtooperateupto
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program
HomeLink to operate it. They do not have the safety feature that causes
the motor to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury.
Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this inf ormation,
contact the manuf acturer of the
equipment.
For quick and accurate training,
make sure the remote transmitter
for the device (garage door,
automatic gate, security system, etc.)
has a fresh battery.
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver fo r about 25 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
If you are training the second or
third buttons, go directly to step 1.
Unplug the garage door opener
motor f rom the electrical outlet.
Holdtheendof thegaragedoor
opener remote transmitter 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red indicator in
HomeLink.
1.
2.
If equipped
CONT INUED
General Inf ormation T raining HomeL ink
Important Saf ety Precautions
Bef ore you begin
HomeL ink Universal Transceiver
Features
181

Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. Press
and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds.
If
the red indicator in HomeLink
continues to flash slowly (does
not flash rapidly), your remote
transmitter may stop
transmitting after a short time.
Go to step 4.
PushandholdtheHomeLink
button for a few seconds, then
watch the red indicator on
HomeLink. If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
If the indicator flashes rapidly
for 2 seconds then stays on, you
have a rolling code transmitter:
go to ‘‘Training with a Rolling
Code System’’ (see page ).
If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5. If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5.
If the red indicator in HomeLink
continues to f lash slowly (does
not begin to f lash rapidly),
repeat steps 2 thru 4.
Plug in the garage door opener
motor, then test the HomeLink
button by pushing it f or about 1 second.
If the button works,
programming is complete.
If the button does not work go
to step 6.
Repeat these steps to train the
other two HomeLink buttons to
operate any other compatible
remotely controlled device around
your home (lighting, automatic
gate, security system, etc.).
3.
4.
5.6.
7.
183
HomeL ink Universal Transceiver
182

Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer.Press and hold the button on
HomeLink f or 3 to 4 seconds.
Press and hold the HomeLink
button again f or 3 to 4 seconds.
This should turn of f the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
Press the HomeLink button again
f or about 1 second. It should
operate the garage door.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes. For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.6.
2. 4.
5.
1. 3.
T raining With a Rolling Code
System
HomeL ink Universal Transceiver
Features
183
TRAINING BUTTON

...................
Radiator Overheating .274
.............
Radio/CD Sound System .115
...........................
Readiness Codes .298
...............................
Rear A/C Unit .113
............
Rear Audio Control Panel .147
........
Rear Entertainment System .142
..
Rear Lights, Bulb Replacement .252
.
Rear View Camera and Monitor .180
............................
Rear View Mirror .92
.................
Rear Window Def ogger .77
.
Rear Window Wiper and Washer .74
..........
Reclining the Seat Backs .87-91
.............................
Reminder Lights .61
................
Remote Audio Controls .138
.................
Remote Control (RES) .169
.......................
Remote Transmitter .83
Replacement Inf ormation
................
Engine Oil and Filter .240
.................................
Floor Mats .254
..........................................
Fuses .279
................................
Light Bulbs .248
........................................
Minder .235
................................
Timing Belt .245
...........................................
Tires .259 .............................
Wiper Blades .255
Replacing Seat Belts Af ter a ............................................
Crash .23
...
Reserve Tank, Engine Coolant .190
...............................
Restraint, Child .38
..................
Reverse Gear Position .201
................................
Rotation, Tire .260
......................................
Saf ety Belts .10
............
Safety Defects, Reporting .304
.................................
Saf ety Features .9
.........................................
Airbags .11
.....................................
Seat Belts .10
.............
Saf ety Labels, Location of . 58
..............................
Saf ety Messages .iii
.........................................
Seat Belts .10
...............
Additional Information . 21
Automatic Seat Belt ...............................
Tensioners .23
.....................................
Cleaning .254
......................
Lap/Shoulder Belt .22
................................
Maintenance .23
Reminder Light and ................................
Beeper . 21, 62 ...................
System Components . 25
...............
Use During Pregnancy . 19
...
Wearing a Lap/Shoulder Belt . 15
....................................
Seat Heaters .86
.................................................
Seats .87
............
Folding the Second Seat . 89
...............
Folding the Third Seat . 90
..........................
Head Restraints .91
.........
Reclining the Second Seat . 89
............
Reclining the Third Seat . 90
.......................
Third Seat Access .90
...................
Se ats, Adjusting the . 87-91
............................
Security System .174
...............................
Serial Number .286
...........................
Service Intervals .229
.............................
Service Manual .305
.........
Service Station Procedures . 187
..........................
Setting the Clock .140
Shif ting the Automatic .............................
Transmission .200
.....
Shif t Lever Position Indicator . 200
........................
Shif t Lock Release .203
Side Marker Lights, Bulb .........................
Replacement in .249
..............................
Side Airbags . 11, 31
..........................
Off Indicator . 34, 63
Index
R
S
VI